• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2004년도 제23회 추계학술대회 논문집
• /
• pp.62-67
• /
• 2004

이 논문에서는 메탄을 연료로 하는 에어터보램제트(ATR) 엔진의 아음속 영역에서의 탈설계점 성능 해석을 수행하였다 이를 위하여 ATR 엔진을 수치적으로 모델링하여 성능을 모사하였다. 각 구성품에 대해 탈설계점 성능을 계산할 수 있도록 모델을 작성하였다. 압축기 작동점은 노즐과의 유량매칭(matching)에 의하여, 터빈 작동점은 일 매칭에 의하여 결정하였다. 성능 해석 결과, ATR 엔진은 기존의 개스 터빈 엔진과 비교해 상당히 다른 탈설계점 특성을 가지고 있음을 보였다.

• 한국분무공학회지
• /
• 제27권1호
• /
• pp.36-41
• /
• 2022

In this study, the combustion instability characteristics according to the change in the hydrogen ratio in the fuel in the single nozzle system of the hydrogen-natural gas mixed gas turbine for power generation was analyzed using a three-dimensional finite element analysis-based Helmholtz solver. This combustor shows the instability characteristics in which mode transition occurs from a mode having a low amplitude near 70 Hz to a mode having a high amplitude of 250 Hz or higher as the hydrogen fraction in the fuel increases. The current modeling results are found to reasonably predict the main characteristics of the change in measured instability frequency and growth rate with the change in fuel composition.

• Tribology and Lubricants
• /
• 제12권4호
• /
• pp.28-34
• /
• 1996

The lubrication characteristics of high-speed ball bearings have been investigated empirically using 45mm bore split inner ring ball bearings employed in small industrial gas turbine engines with oil-jet lubrication method. For the close structural simulation, experiments carried out with bearing mounting supports of real engines, such as bearing housings and oil nozzle assemblies with squeeze film dampers. Thus the results of tests can be directly applied to the design and the development of gas turbine engines. Testing was done by varying operating speeds, axial load on bearings, and lubricant flow rates. During testing, the temperature of bearing at outer-ring face, the power consumption of the driving motor, and the rotating resistance of the bearing were measured. From this study, the representative factors for lubrication characteristics at high speed was found, and the most important one was not operating speed but axial load up to 1.95 million dmN speed and 2969 N axial load. Furthermore, the detailed variation of the rotational resistance of the bearing could be visualized by measuring the change of the radial load under the bearing supports. The rotational resistance consists of the frictional resistance and the bearing-cavity oil resistance.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2002년도 학술대회지
• /
• pp.279-282
• /
• 2002

Recently, gas turbines for power generation adopt multistage DLN(Dry Low NOx) type combustion, where diffusion combustion is applied at low load and, with increase in load, the combustion mode is changed to lean premixed combustion to reduce NOx emissive concentration. However, during the mode changeover from diffusion to premixed flame, unfavorable phenomena, such as flashback, high amplitude combustion oscillations, or thermal damage of combustor parts could frequently occur. In the present study, to apply for the analysis of such unfavorable phenomena, three-dimensional CFD investigations are carried out to compare the detailed flow characteristics and temperature distribution inside the gas turbine combustor before and after combustion mode changeover. The fuel considered here is pure methane gas. A standard $k-{\varepsilon}$ turbulence model with wall function and a P-N type radiation heat transfer model, have been utilized. To analyze the complex geometric effects of combustor parts on combustion characteristics, fuel nozzles, a swirl vane f3r fuel-air mixing, and cooling air holes on the combustor liner wall, are included in this simulation.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2017년도 제48회 춘계학술대회논문집
• /
• pp.881-888
• /
• 2017

일반적으로 다단 축류 터빈은 높은 압력비에서 유동 가속으로 인하여 특정 단에서 초킹 현상이 발생하게 된다. 초킹의 경우 유량 변화 없이 압력비만 증가하게 되며, 이러한 특성을 입구 유량 경계조건을 사용하는 일반적인 평균반경해석법을 이용하여 예측하는데 한계가 있다. 본 연구에서는 이러한 문제점을 해결하기 위해 초킹 영역에서의 성능을 예측하는 알고리즘을 재안하였다. 초킹 지점 이후에는 초킹이 발생하는 노즐 혹은 로터 출구 유동이 팽창하는 특성을 반영하여 고정된 유량 조건에서 압력비가 변할 수 있도록 알고리즘을 구성하였다. 이러한 결과를 다단 축류 터빈 전산해석 결과 및 실험결과와 비교하여 신뢰성을 확인하였다.

• 한국연소학회지
• /
• 제19권3호
• /
• pp.44-52
• /
• 2014

Solid oxide fuel cell(SOFC) makes electric power using hydrogen or reformed from methane and emits high temperature products that contain flammable species like hydrogen, carbon monoxide and methane which varies with operation condition. SOFC/gas turbine integrated system which uses thermal and chemical energy of the discharges is more efficient than SOFC itself. Burning character of the SOFC products will affect the efficiency and stability of the system. Experiments were conducted to know the characteristics of the flame for two typical composition of SOFC products, i.e. start-up and steady state composition. When coflowing air temperature was higher than $600^{\circ}C$, auto-ignitin occurred for both fuels. Though start-up fuel has higher contents of hydrogen, it makes longer flame than steady state composition. It was inferred that the amount of oxidizer necessary to burn makes this phenomenon. Steady state composition fuel was unstable since it contains lots of water. Nozzle that had 6 holes, distance between each hole was 16.7 times of hole diameter, improved the stability of the flame.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1996년도 제24회 춘계학술대회
• /
• pp.86-93
• /
• 1996

The lubrication characteristics of high-speed ball bearings has been investigated empirically using 45mm bore split inner ring ball bearings employed in small industrial gas turbine engines with oil-jet lubrication method. For the close structural simulation, experiments carried out with bearing mounting supports of real engines, such as bearing housings and oil nozzle assemblies with squeeze film dampers. Thus the results of tests can be directly applied to the design and the development of gas turbine engines. Testing was done by varying operating speeds, axial load on bearings, and lubricant flowrates. During testing, the temperature of bearing at outer-ring face, the power consumption of the driving motor, and the rotating resistance of the bearing were measured. From this study, the representative factors for lubrication characteristics at high speed was found, and the most important one was not operating speed but axial load up to 1.95 million dmN speed and 303 kgf axial load. Furthermore, the detailed variation of the rotational resistance of the bearing could be visualized by measuring the change of the radial load under the bearing supports. The rotational resistance consists of the frictional resistance and the bearing-cavity oil resistance.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 추계학술대회논문집 II
• /
• pp.1388-1392
• /
• 2001

In this paper, an experimental method of several modal analyses was devised to iify the vibration characteristics of G/T blade in power plants. Also, it is being applied this method to establish the standard category of natural frequency of new developed blades. So acceptance margin to avoid resonance due to nozzle waking force is being established for new blades. It is expected to improve the availability of G/T blades by using the result of this study.

• 한국항공우주학회지
• /
• 제35권2호
• /
• pp.143-148
• /
• 2007

액체 추진 로켓을 구동하는 충동형 터빈은 크기가 작고 가벼워야 하며 큰 출력을 발생시켜야 한다. 충동형 터빈은 초음속 조건에서 작동되기 때문에 유동 특성이 매우 복잡하여 성능 예측은 주로 수치해석에 의존해 왔다. 그러나 신뢰성을 확보하기 위하여는 해석결과를 실험으로 검증하는 과정이 필요하다. 본 연구에서는 설계에 사용되는 주요 변수들의 영향을 확인하기 위하여 회전하는 3차원 축류 터빈을 2차원 형상으로 모사하여 실험하였다. 먼저 노즐 출구에서의 마하수를 측정하였으며, 이론적인 노즐 추력식을 유도하여 터빈 블레이드에 작용하는 깃하중을 계산하였고 측정된 결과와 비교하였다. 또한 추력 계수를 구하고 이를 통해 터빈 출력을 예측하여 설계 요구 조건의 타당성을 확인하였다

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2009년도 춘계학술대회 논문집
• /
• pp.263-266
• /
• 2009

본 연구는 GE 7FA+e DLN 2.6 가스터빈 연소기를 축소 제작한 모형 가스터빈 연소기의 연소 동특성 및 연소불안정 현상을 알아보고 위해 진행되었다. 모형 연소기에 사용된 연료노즐은 1/3 크기로 상사하여 제작되었으며, 실제 연료노즐과 동일한 2단 스월러(swirl vane)를 가지고 있다. Plenum과 연소기의 형상은 실 가스터빈과 유사한 음향학적 특성을 가질수 있도록 설계되었다. 실험은 공기온도 $200{\sim}400^{\circ}C$, 대기압, 노즐출구 속도 $30{\sim}75\;m/s$, 당량비 $0.4{\sim}1.2$, 연소실 길이 $375{\sim}700\;mm$,에서 이루어졌으며, 그 결과 소염영역 근처의 저 당량비 영역과 당량비 1.1 이상인 연료 과농 상태에서 연소 불안정 현상이 관찰 되었다.