• 해양환경안전학회:학술대회논문집
• /
• 해양환경안전학회 2018년도 공동국제학술발표회
• /
• pp.190-190
• /
• 2018

• Journal of Chest Surgery
• /
• 제24권12호
• /
• pp.1225-1227
• /
• 1991

Pneumomediastinum and subcutaneous emphysema produced by air turbine dental drills, although widely reported in dental publications, are rarely reported in the thoracic journals. We report a case of 38-year-old man with pneumomediastinum and subcutaneous emphysema after use of a air turbine dental drill for dental extraction.

• 한국지능시스템학회:학술대회논문집
• /
• 한국퍼지및지능시스템학회 1997년도 추계학술대회 학술발표 논문집
• /
• pp.37-40
• /
• 1997

This paper presents a performance improvement of distributed fuzzy control system by changing the triangular membership function widths according to the input variables. The control region consists of 4 parts according to the sign of error and change of error terms. Each control part is operated by the suitable nonuniform triangular membership function. Through the simulation for the boiler-turbin model of a fossil power plant using decentralized contol, it is verified this proposal

• 전기학회논문지
• /
• 제63권4호
• /
• pp.445-450
• /
• 2014

Jeju power system is connected to the mainland power system through HVDC, and receives about half of required electricity through the HVDC lines. Jeju power system already experienced black out when a generator tripped at the moment of the HVDC line faults. But, UFR operated as was expected when HVDC line fault occurred at that time. As the penetration level of wind turbines increases, it is required to set UFR again considering intermittent wind turbin outputs. In this paper, we address a new way of UFR setting through computer simulation.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 A
• /
• pp.354-356
• /
• 2000

This paper describes the strategy of a daily optimal operational scheduling on cogeneration systems with each other generation mode. The cogeneration systems consists of three generators. auxiiiary devices which are three auxiliary boilers, two waste boilers and three sludge incinerators. One unit that using the back pressure turbin generates the electrical and the thermal energy. The other two units that using the extraction condensing turbine generate the energy. Auxiliary devices operate to supplement the thermal energy to the thermal load with three units. The cogeneration system has a large capacity which is able to supply enough the thermal energy to the thermal load, however the electric power generated is insufficient to satisfy the electrical load. Therefore the insufficient electric energy is supplemented by buying electrical energy from the utility. Simulation was carried out using optimization toolbox. The result reveals that the proposed modeling and strategy can be effectively applied to cogeneration systems with each other generation mode.

• 한국해양공학회지
• /
• 제7권2호
• /
• pp.37-43
• /
• 1993

The simplest vibrtion absorber is the impact damper which consists of a small mass allowed to impact between two gaps sp that energy is dissipated by conversion into noise and heat. Impact damping is a passive vibration control technique to attenuate the vibrations of lightly damped. It has been investigated to reduce the excessive vibrations of turbin blades, radar antennas, machine tools and tall light poles. In this paper, the efficiency of impact vibration absorber was investigated. A steady state vibration of two equispaced impacts per cycle was assumed. The analysis based on the assumption has been considered and the theory is examined experimentally.

• 대한기계학회논문집
• /
• 제18권9호
• /
• pp.2413-2422
• /
• 1994

The effects of compressor design conditions on the off-design performance of a single-shaft gas turbine engine have been studied. Three different geometric design conditions are considered and three different values for the specific mass flow rate at the inlet to the compressor are assumed. For each of nine compressor design, the off-design performance of the gas turbine engine is predicted using the method previously proposed by present authors. Results show that the predicted off-design performances are quite different from each other even though they have the same performance at design point: it means that compressor design conditions should be determined in consideration of the off-design performance of the engine. The specific mass flow rate at the inlet to the compressor is also shown that it might be optimized with respect to the net power of the engine.

• 대한기계학회논문집A
• /
• 제20권5호
• /
• pp.1458-1467
• /
• 1996

A direct differentiationmethod is presented for the shape design sensitivity analysis of axisymmeetric elastic solids. Based on the exisymmetric boundary integralequaiton formulation, a new boundary ntegral equatio for sensitivity analysis is derived by taking meterial derivative to the same integral identity that was used in the adjoint variable melthod. Numerical implementation is performed to show the applicaiton of the theoretical formulation. For a simple example with analytic solution, the sensitivities by present method are compared with analytic sensitivities. As an application to the shape optimization, an optimal shape of a gas turbine disc toinimize the weight under stress constraints is found by incorporating the sensitivity analysis algorithm in an optimizatio program.

• 제어로봇시스템학회논문지
• /
• 제6권4호
• /
• pp.254-260
• /
• 2000

This paper deals with the development of fault tolerant control for a nonlinear boiler system with noise and disturbance. The MCMBPC(Multivariable Constrained Model Based Predictive Control) is adopted for the control of the specific boiler turbin model. The fault detection and diagnosis are accomplished with the Kalman filter and two bias estimators. Once a fault is detected, two Bias estimators are driven to estimate the fault and to discriminate Process fault and sensor fault. In this paper, a fault tolerant control scheme combining MCMBPC with a fault compensation method based on the bias estimator is proposed. The proposed scheme has been applied to the nonlinear boiler system and shown a satisfactory performance through some simulations.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2006년도 춘계 학술대회 개요집
• /
• pp.274-276
• /
• 2006

Weldability of high Cr ferritic steel for $620^{\circ}C$ grade turbin casing were investigated. The effect of carbon content on the cold and hot cracking susceptibility and HAZ softening was determined. The cast steel with higher carbon content showed higher HAZ hardness because of the dissolution of cabonitrides during welding thermal cycle. Moreover, it showed higher solidification cracking sensitivity because of the little S-ferrite formation in weld metal. Both steels showed HAZ softening at $900^{\circ}C$ peak temperature after PWHT.