• Journal of Surface Science and Engineering
• /
• v.53 no.5
• /
• pp.257-264
• /
• 2020

Anodization of Fe and Fe alloys is one of the most promising techniques to obtain iron oxide films applying to the various electrochemical devices due to their electrochemical catalytic properties. In this study, we investigate on the preparation of anodic iron oxide composite incorporated with WO₃ through a single-step anodization of stainless steel type-304 (STS304) as a substrate. The effects of applied voltage and tungsten precursor on the structural characteristics of iron oxide composite with different amount of incorporated WO₃ were observed. It is demonstrated that when the voltage of 60 V applied with 20 mM of Na₂WO₄ as a precursor, anodic iron oxide composite with a large pore diameter and a thick oxide length in which WO₃ is uniformly incorporated is obtained.

• Transactions of Materials Processing
• /
• v.27 no.6
• /
• pp.370-378
• /
• 2018

Cold forging, carried out at room temperature, leads to high dimensional accuracy and excellent surface integrity as compared to other forging methods such as warm and hot forgings. In the cold forging process, WC-Co (Tungsten Carbide-Cobalt) alloy is the mainly used material as a core dies because of its superior hardness and strength as compared to other structural materials. For cold forging, die life is the most significant factor because it is directly related to the manufacturing cost due to periodic die replacement in mass production. To investigate die life of WC-Co alloy for cold forging, mechanical properties such as strength and fatigue are essentially necessary. Generally, uniaxial tensile test and fatigue test are the most efficient and simplest testing method. However, uniaxial tension is not efficiently application to WC-Co alloy because of its sensitivity to alignment of the specimen due to its brittleness and difficulty in thread machining. In this study, shape of specimen, tools, and testing methods, which are appropriate for uniaxial tensile test for WC-Co alloy, are proposed. The test results such as Young's modulus, tensile strength and stress-strain curves are compared to those in previous literature to validate the proposed testing methods. Based on the validation of test results it was concluded that the newly developed testing method is applicable to other cemented carbides like Titanium carbides with high strength and brittleness, and also can be utilized to carry out fatigue tests for further investigation on die life of cold forging.

• Journal of Welding and Joining
• /
• v.28 no.4
• /
• pp.73-80
• /
• 2010

In this work, the effect of welding variables on weldability of gas tungsten arc(GTA) welding was investigated with experimental analysis for a commercial pure(CP) titanium (Grade.1). The GTA welding tests on sheet samples with 0.5mm in thick were carried out at different process variables such as arc length, welding speed and electrode shape. In order to search an optimum arc length with full penetration, bead- on-plate welding before butt-welding were performed with different arc length conditions. From the bead- on-plate welding results, the optimum condition considering arc stability and electrode loss was obtained in the arc length of 0.8mm. Butt-welding tests based on the arc length of 0.8mm were carried out to achieve the optimum conditions of welding speed and electrode shape. Optimum conditions of welding speed and electrode shape were suggested as 10 mm/s and truncated electrode shape, respectively. It was successfully validated by the microstructural observation, tensile tests, micro-hardness tests and formability tests.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.10
• /
• pp.206-211
• /
• 2020

Tungsten alloys are used widely in general industrial fields, but they are difficult to cast, so products are manufactured using powder metallurgy. In this study, a mixed powder of tungsten, nickel, and iron homogenized using a ball mill was added to pure water as a solvent, and PVA as a binder was added to prepare a spray drying mixture. The mixed liquid was prepared using a spraying machine. A study was carried out to produce a granular powder that can reduce the variations between products during the molding and sintering process of the powder metallurgy method. A preliminary experiment was conducted to confirm the influence of the variables in the granulation process. Through the preliminary test results, this experiment was performed with the volume of solvent of the spray drying the mixture as an independent variable, and granular powder having a mean particle size similar to that of the existing mass-production conditions and an increased apparent density was prepared. In addition, a pilot test was conducted for the molding and sintering process. The improved granular powder reduced the characteristic variation (weight variation) of the mass-produced product.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.3 no.2
• /
• pp.3-9
• /
• 2004

The main objectives of this paper are to determine optimum cutting conditions using experimental design method to manufacture pedicle screws. Generally, titanium alloys are known as difficult-to cut materials. In the machining of titanium alloy, high cutting temperature and strong chemical affinity between the tool and the work material are generated because of Its low thermal conductivity and chemical reactivity. Such phenomenon cause increase of tool wear and deterioration of surface quality. Thus, in this paper, required experimental investigations are performed to evaluate the machinability of titanium materials With tungsten carbide tools Required simulation and experiments are performed, and the results are investigated.

• Proceedings of the KWS Conference
• /
• 2004.05a
• /
• pp.176-178
• /
• 2004

Gas tungsten arc welds on Al-4 wt% Cu alloys were investigated to determine effects of gravitational orientation on the weld solidification behavior. Outward convection flows in the parallel-down weld might be inhibited because of its reverse direction with respect to the gravity vector. This resulted in abnormal 'S' shape of the trailing s-1 interface and the solidification rate (Vs), which was receded toward the weld pool center. Significant influence of gravitational orientation resulted in the variation on the weld pool shape associated with convection flows, which in turn affected solidification orientation/morphology and the primary dendrite spacing(λ$_1$).

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1120-1125
• /
• 2004

Welding characteristics of STS304 stainless steel and Inconel 600 using a continuous wave Nd:YAG laser are experimentally investigated. Alloy 600 being used in steam generator tubing of pressurized water reactor(PWR) exposed to some corrosion environment, stress corrosion cracking can occur on this material. Presented here are the results from a series of experiments in which dissimilar metal welds were made using the gas tungsten arc welding process with pure argon shielding gas. But It is well known that solidification cracking susceptibility of austenitic alloys depends on the solidification temperature range and amount/distribution of solute rich liquid that exists at the terminal stages of solidification. An experimental study was conducted to determine effects of welding parameters and to optimize those parameters that have the most influence on eliminating or reducing the extent welding zone formation at dissimilar metal welds.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.62-63
• /
• 2006

Both densification and grain growth are driven by the reduction of the interfacial area, kinetics of which depends strongly on the interface structure. Abnormal grain coarsening in the system of singular solid/liquid interface such as WC-Co alloys was explained by the growth mechanism of 2-dimensional nucleation. Based on this concept, the marked inhibition of coarsening of WC grains by VC addition can be approached by the increase in the step free energy, which increases the barrier of 2-dimensional nucleation. The activated sintering in tungsten powders can be approached by the interface structure change induced by the addition of a small amount of nickel.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.66-67
• /
• 2006

The master sintering curve (MSC) is derived from densification data over a range of heating rates and temperatures. To improve the accuracy, several modifications were proposed: multi-phase MSC for solid state sintering with phase changes, MSC for liquid phase sintering, and MSC with consideration of grain growth. The developed MSC models were applied to several material systems such as molybdenum, stainless steels, and tungsten heavy alloys (WHA), in order to evaluate the effect of compaction pressure, phase change, grain growth, and composition on densification, to classify regions having different sintering mechanism, and to help engineer design, optimize, and monitor sintering cycles.

• Journal of the Korean Society of Safety
• /
• v.23 no.6
• /
• pp.1-6
• /
• 2008

Machine operator and quality are affected by chip during cutting process to product machine parts. This paper presents a study of the influence of cutting conditions on the surface roughness obtained by turning using Taguchi method for safety of turning operator. In the machining of titanium alloy, high cutting temperature and strong chemical affinity between the tool and the work material are generated because of its low thermal conductivity and chemical reactivity. Therefore titanium alloys are known as difficult-to materials. An orthogonal array, the signal-to-noise ratio, the analysis of variance are employed to investigate the cutting characteristics of implant material bars using tungsten carbide cutting tools of throwaway type. Also Experimental results by orthogonal array are compared with optimal condition to evaluate advanced reliability. Required simulations and experiments are performed, and the results are investigated.