• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.30A no.12
• /
• pp.69-76
• /
• 1993

The statistical methodology using RSM (response surface method) was used too ptimize the deposition conditions of selective CVD tungsten process for improving the deposition rate and the adhesion property. Temperature, flow rate of SiH$_4$ and WF$_6$ and H$_2$ and Ar carrier gases were chosen for the deposition variables and process characteristics due to carrier gas were intensively investigated. It was observed that temperature was the main factor influencingthe deposition rate in the case of H$_2$ carrier gas while the reactant ratio, $SiH_{4}/WF_{6}$, had the principal effect on the deposition rate in the case of Ar carrier gas. The increased deposition rate and the good adhesion to Si were obtained under Ar carrier gas compared to H$_2$ carrier gas. The optimum conditions for deposition rate and antipeeling property were found to be the temperature range of 300~32$0^{\circ}C$ and the reactant ratio, $SiH_{4}/WF_{6}$, of 0.5~0.6.

• Transactions on Electrical and Electronic Materials
• /
• v.15 no.6
• /
• pp.344-347
• /
• 2014

This study was carried out on DLC thin film deposition technology used in infrared optical system production as a method of reducing the shape changes of the molding core and the consequent loss of life. Experiments on the deposition on silicon wafer and tungsten carbide used as a substrate for molding core were conducted at each processing condition using a filtered arc system, and it was found that the surface and mechanical properties were of the greatest quality when the substrate bias voltage of -150 V was used. In addition, it was confirmed that the PV and Ra characteristics were improved by the deposition of the DLC thin film.

• Economic and Environmental Geology
• /
• v.18 no.1
• /
• pp.11-22
• /
• 1985

The Daehwa and Donsan tungsten-molybdenum deposits are composed of numerous fissure-filling veins developed in Precambrian gneiss and Cretaceous granite and quartz porphyry. K-Ar age of biotite in granite and that of muscovite in ore veins are $105{\pm}5\;Ma$ and 88.2~88.6 Ma respectively. Occurrence of ore deposits shows that relevant igneous rock is possibly quartz porphyry rather than above mentioned granite in temporal view point. Vein structure and mineralogy suggest that ore veins were formed by continuous vein filling, not by repeated mineralization. Three distinct depositional stages with decreasing age can be devided on the basis of mineral paragenesis and fluid inclusion studies: Stage I, deposition of oxides and silicates; stage II, deposition of base-metal sulfides and sulfosalts with carbonates; stage III, deposition of barren calcite and fluorite. Tungsten, molybdenum and tin mineralization occurred in stage I.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.8
• /
• pp.2416-2418
• /
• 2010

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.1225-1226
• /
• 2006

Particles of high strength material when coated with silver offer a means of obtaining desirable electrical properties and high strength. The coating process employed aqueous ammoniacal silver-nitrate electrolytes with a formaldehyde solution as the reductant. Modifying additives were also applied. The reduction and subsequent deposition of silver occurred selectively on the surface of the tungsten particles. The morphologies of the coated particles were assessed by SEM imaging. The silver was uniformed coated on tungsten powder and its thickness was estimated to be approximately 100nm on the basis of a mass account.

• Korean Journal of Materials Research
• /
• v.26 no.9
• /
• pp.486-492
• /
• 2016

Tungsten (W) thin film was deposited at $400^{\circ}C$ using pulsed chemical vapor deposition (pulsed CVD); film was then evaluated as a nucleation layer for W-plug deposition at the contact, with an ultrahigh aspect ratio of about 14~15 (top opening diameter: 240~250 nm, bottom diameter: 98~100 nm) for dynamic random access memory. The deposition stage of pulsed CVD has four steps resulting in one deposition cycle: (1) Reaction of $WF_6$ with $SiH_4$. (2) Inert gas purge. (3) $SiH_4$ exposure without $WF_6$ supply. (4) Inert gas purge while conventional CVD consists of the continuous reaction of $WF_6$ and $SiH_4$. The pulsed CVD-W film showed better conformality at contacts compared to that of conventional CVD-W nucleation layer. It was found that resistivities of films deposited by pulsed CVD were closely related with the phases formed and with the microstructure, as characterized by the grain size. A lower contact resistance was obtained by using pulsed CVD-W film as a nucleation layer compared to that of the conventional CVD-W nucleation layer, even though the former has a higher resistivity (${\sim}100{\mu}{\Omega}-cm$) than that of the latter (${\sim}25{\mu}{\Omega}-cm$). The plan-view scanning electron microscopy images after focused ion beam milling showed that the lower contact resistance of the pulsed CVD-W based W-plug fill scheme was mainly due to its better plug filling capability.

• Korean Journal of Materials Research
• /
• v.1 no.4
• /
• pp.177-183
• /
• 1991

Change of the properties of selective CVD-W by $SiH_4$ reduction with the variation of deposition time and pressure has been investigated. The lime required for covering the who)to Si substrate by tungsten at $300^{\circ}C$ under the pressure of 100mtorr is approximately 30 seconds. The film thickness tends to increase linearly in the early stage of deposition process and parabolically later, sheer resistance of the film tends to decrease rapidly initially, and slowly later with deposition time. Tungsten grain size does not change much, but grain boundary becomes hazy in the pressure range of 50-300mtorr. Also no ${\beta}-W$ but only ${\alpha}-W$ was found in this pressure range. The deposition rate and electrical resistivity of tungsten tend to increase wish increasing pressure. The results of AES analysis show that pressure does not much affect Si/W ratio of the tungsten film and silicidation at the W/Si interface.

• Korean Chemical Engineering Research
• /
• v.43 no.4
• /
• pp.495-502
• /
• 2005

Copper was plated on the tungsten substrate by use of a direct copper electroless plating. The optimum deposition conditions were found to be with a concentration of $CuSO_4$ 7.615 g/L, EDTA of 10.258 g/L, and glyoxylic acid of 7 g/L, respectively. The solution temperature was maintained at $60^{\circ}C$. The pH was varied from 11.0 to 12.8. After the deposition, the properties of the copper film were investigated with X-ray diffractometer (XRD), Field emission secondary electron microscope (FESEM), Atomic force microscope (AFM), X-ray photoelectron spectroscope (XPS), and Rutherford backscattering spectroscope (RBS). The best deposition condition was founded to be the solution pH of 11.8. In the case of 10 min deposition at the pH of 11.8, the grain shape was spherical, Cu phase was pure without impurity peak ($Cu_2O$ peak), and the surface root mean square roughness was about 11 nm. The thickness of the film turned out to be 140 nm after deposition for 12 min and the deposition rate was found to be about 12 nm/min. Increase in pH induced a formation of $Cu_2O$ phase with a long rectangular grain shape. The pH control seems to play an important role for the orientation of Cu in electroless deposition. The deposited copper concentration was 99 atomic percent according to RBS. The resulting Cu/W film yielded a good adhesive strength, because Cu/W alloy forms during electroless deposition.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.05b
• /
• pp.54-56
• /
• 2001

The $SiH_4$ soak step is widely used during the CVD Tungsten(W) plug deposition process on the Ti/TiN barrier metal to prevent the $WF_6$ attack to the underlayer metal. We tried to reduce or skip the time of $SiH_4$ soak process to optimize W-plug deposition process on Via. The electrical characteristics including Via resistance and the structure of W film are affected according to $SiH_4$ soak time. The elimination possibility of $SiH_4$ soak process was confirmed in the case of that the CVD W film grows on the stable Ti/TiN underlayer.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.39 no.7
• /
• pp.692-701
• /
• 1990

New selective tungsyen deposition deposition on silicon process is described which makes use of a previously unreported, alternating cyclic,