• Corrosion Science and Technology
• /
• 제8권3호
• /
• pp.126-131
• /
• 2009

The interaction between wear and corrosion can significantly increase total material losses in water chemistry environment. The corrosive wear tests of a PWR steam generator tube material (Alloy 690) against the anti vibration bar material (409 SS) were performed at room temperature. The tests were performed in alkaline water chemistry conditions. NaOH solution was selected for test condition to investigate the corrosive wear effect of steam generator tube material in alkaline pH condition without other factors. The flow induced vibration can caused tube damage and the corrosion can be occurred by water chemistry. The test results showed that, in the alkaline solution at pH 13.9, the corrosion current density was increased about ten times than that in the distilled water. And wear rate at pH 13.9 was increased about ten times from that at neutral condition. However, the wear rate was decreased with time. The decrease would be attributed to the change in roughness of specimen or sub-layer of the worn surface with time. From microstructure observation, severe abrasive shape and several wear debris were found. From those results, it could infer that the oxide film on Alloy 690 changed to easily breakable one in the alkaline water, and then abrasion with corrosion became the main wear mechanism.

• Steel and Composite Structures
• /
• 제12권3호
• /
• pp.261-273
• /
• 2012

This study proposes and examines a circular composite bridge pier for seismic resistance. The axial and flexural strengths of the proposed bridge pier are provided by the longitudinal reinforcing bars and the concrete, while the transverse reinforcements used in the conventional reinforced concrete pier are replaced by the steel tube. The shear strength of this composite pier relies on the steel tube and the concrete. This system is similar to the steel jacketing method which strengthens the existing reinforced concrete bridge piers. However, no transverse shear reinforcing bar is used in the proposed composite bridge pier. A series of experimental studies is conducted to investigate the seismic resistant characteristics of the proposed circular composite pier. The effects of the longitudinal reinforcing bars, the shear span-to-diameter ratio, and the thickness of the steel tube on the performance of strength, ductility, and energy dissipation of the proposed pier are discussed. The experimental results show that the strength of the proposed circular composite bridge pier can be predicted accurately by the similar method used in the reinforced concrete piers with minor modification. From these experimental studies, it is found that the proposed circular composite bridge pier not only simplifies the construction work greatly but also provides excellent ductility and energy dissipation capacity under seismic lateral force.

• 대한치과보철학회지
• /
• 제54권1호
• /
• pp.41-48
• /
• 2016

치아 상실에 이어 심각한 치조골 소실을 보이는 무치악 환자들은 전통적인 방식의 총의치를 사용하는데 어려움이 많다. 이러한 문제를 보완할 수 있도록 임플란트를 이용한 피개의치가 사용되고 있다. SFI-bar$^{(R)}$는 진료실에서 직접 조정이 가능한 기성품으로 복잡한 기공과정을 필요로 하는 기존의 바 시스템보다 간결하여 시간과 비용을 절감할 수 있다. 첫 번째 증례는 55세 남자 환자로 기존 하악 임플란트-지지 피개의치가 파절되었다는 주소로 내원하였고 내구성이 있으며 통증이 없는 의치를 원하였다. 파절된 Locator$^{(R)}$ 어태치먼트를 제거 후 바를 이용한 피개의치로 치료하였다. 두 번째 증례는 파킨슨병을 앓고 있는 77세 여자 환자로 하악 치조골이 심각하게 흡수되어 의치가 자주 탈락한다는 주소로 내원하였고 통증이 없고 유지력이 있는 의치를 원하였다. 하악 전치부에 두개의 임플란트를 식립한 후 임플란트에 연결된 어댑터에 바를 연결하였다. 그 후 바에 맞는 여성부를 새로운 의치에 장착하여 치료하였다. 2년의 추적 관찰 결과 상기 환자 모두 심미적, 기능적으로 만족할만한 결과를 보였으므로 증례를 보고하고자 한다.

• 한국식품과학회지
• /
• 제28권3호
• /
• pp.475-481
• /
• 1996

초임계유체를 이용하여 간단하고, 신속하고, 저렴하게 식품 중의 잔류농약을 추출, 정제하는 방법을 개발하기 위하여 10종의 유기염소계 농약에 대하여 ppm수준의 농도에서 초임계 이산화탄소를 이용하여 추출 온도 및 압력 등 추출조건을 달리하여 추출수율을 측정하였다. 초임계 이산화탄소 추출에 의한 유기염소계 잔류농약 표준용액의 회수율은 103bar에서 추출온도가 증가할수록 증가하였다. 유기염소계 잔류농약 표준용액의 최대 평균 회수율은 $40^{\circ}C/172\;bar.$에서 98.3%였다. 대구, 넙치, 오징어에 첨가한 유기염소계 농약의 평균 첨가회수율은 $40^{\circ}C/172\;bar.$에서 각각 85.6, 74.6, 83.0%였다.

• 한국공작기계학회논문집
• /
• 제14권4호
• /
• pp.69-74
• /
• 2005

Nowadays CFC and HCFC refrigerants are restricted because they causes to depletion of ozone layer. Accordingly, an experiment is apply to the $NH_3$ gas for refrigerant to study the performance characteristic and to improve the energy efficiency. An experiment are carried out for the condensed pressure in a range from 14.5bar to 16bar and for degree of superheat in a range from 0 to $10^{\circ}C$ at each condensed pressure. As the result of experiment, when degree of superheat is $1^{\circ}C$ and condensed pressure is 14.5bar, the refrigeration system showed the high performance.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1996년도 춘계학술발표회논문집(2)
• /
• pp.82-87
• /
• 1996

To find the effects of pressure on critical heat flux (CHF) for the conditions of low pressures (especially up to 10 bar) and low mass flux (~300 kg/$m^2$s), a series of experiments have been accomplished by using uniformly heated Inconel-625 tube. The experimental ranges are as follows: pressure (from 1.2 to 8 bar). mass velocities (from 100 to 250 kg/$m^2$s) and the inlet subcooling ($\Delta$h$_{i}$ ＝ 350 kJ/kg). According to the experimental data, it is found that the CHF is nearly independent of the pressure and increases with mass flux. From the results of the CHF correlation assessment for this experimental data, we could find somewhat different tendency of CHF behavior from every other CHF prediction correlation and table.ation and table.

• Steel and Composite Structures
• /
• 제21권1호
• /
• pp.73-91
• /
• 2016

The use of box columns has been increased due to the rigidity in rigid orthogonal moment resisting frames. On the other hand, the installation and welding of necessary horizontal continuity plates inside the columns are both labor-consuming and costly tasks. Accordingly, in this paper, a new beam-to-box column connection by trapezoidal external stiffeners and horizontal bar mats is presented to provide seismic parameters. The proposed connection consists of eight external stiffeners in the level of beam flanges and five horizontal bar mats in Concrete Filled Tube (CFT) columns. The new connection effectively alleviates the stress concentration and moves the plastic hinge away from the column face by horizontal external stiffeners. In addition, the result shows that proposed connection has provided the required strength and rigidity of connection, so that the increased strength, 8.08% and rigidity, 3.01% are compared to connection with internal continuity plates, also the results indicate that this connection can offer appropriate ductility and energy dissipation capacity for its potential application in moment resisting frames in seismic region. As a result, the proposed connection can be a good alternative for connection with continuity plates.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2005년도 동계학술발표대회 논문집
• /
• pp.579-584
• /
• 2005

Nowadays heat exchangers that have been applied for freon refrigerating systems, a shell and tube type condenser and a flooded evaporator have been used, but because of their large size, large space for installation and amount of refrigerants are needed. In this study, we will find the most suitable operating condition of shell and disk type optimum heat exchanger which can minimize the amount of a refrigerant and allow its minimum leakage. The condensing pressure of refrigeration system is increased from 15.0bar to 16.0bar and degree of superheat is increased from 0 to $10^{\circ}C$ at each condensing pressure. As a result of study, It revealed that shell and disk type heat exchanger was applicable to the freon refrigeration system

• 한국항공우주학회지
• /
• 제44권6호
• /
• pp.484-491
• /
• 2016

본 연구의 목적은 항공기 메커니즘 구조물에 사용되는 금속 소재 토크바를 복합소재를 이용하여 무게절감이 가능한 구조물을 개발 하는것에 있다. 토크바에 주어진 하중조건 및 구조물의 설계 경계조건에 부합하는 유한요소모델을 이용하여 구조해석을 수행 하였다. 이를 바탕으로 최적화된 복합소재의 적층 조건 및 토크바의 두께 요건을 설정하였다. 설계요건에 맞게 제작된 시제품을 이용하여 복합소재 토크바의 비틀림 시험을 실시하였으며, 동구조 시험을 통해서 토크바의 강도 및 강성 요구조건을 만족한다는 것을 증명하였다.

• Steel and Composite Structures
• /
• 제34권1호
• /
• pp.53-73
• /
• 2020

A novel all-steel miniature bar-type structural fuse (MBSF) with cold formed bolted connections is developed in this study, which consists of a central energy dissipation core cut from a smooth round bar, an external confining tube and nuts. Three types of cross sections for the central energy dissipation core, i.e., triple-cut, double-cut and single-cut cross sections, were studied. Totally 18 specimens were axially tested under either symmetric or asymmetric cyclic loading histories, where the parameters such as cut cross sectional area ratio, length of the yielding portion and cross sectional type were investigated. Numerical simulation of 2 representative specimens were also conducted. An analytical model to evaluate the bending failure at the elastic portion was proposed, and a design method to avoid this failure mode was also presented. The experimental results show that the proposed MBSFs exhibit satisfactory hysteretic performance under both the two cyclic loading histories. Average strain values of 8% and 4% are found to be respectively suitable for designing the new MBSFs as the ultimate strain under the symmetric and asymmetric cyclic loadings.