• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.1
• /
• pp.39-45
• /
• 2009

The CRT(Cathode Ray Tube) displays have been substituted for FPDs(Flat Panel Displays) such as LCD(Liquid Crystal Display) and PDP(Plasma Display Panel) because they have a convex surface, large volume and heavy weight. The productivity of FPDs is greatly dependent on the area of thin glass panel with $0.6{\sim}0.8mm$ thickness because FPDs are manufactured by cutting a large-scaled thin glass panel with patterns to the required product dimensions. So FPD's industries are trying to increase the area of thin glass Panel. Through FEM(Finite Element Method) analysis and fluid analysis, we developed an non-contact and air-floating conveyor system which consists of transport-module, distributor, horizontal/vertical changer and controller for the 7th generation glass panel (2,200mm in width, 1,870mm in length and 0.7mm in thickness). The design technology developed in this study can be effectively applied to a conveyor system for a larger-scaled thin glass panel.

• Journal of Korea Water Resources Association
• /
• v.49 no.4
• /
• pp.347-359
• /
• 2016

Flow input from the basin will not remain the same as before due to climate changes. Since the predictions on river discharge due to climate change is given by scenarios, various discharge scenarios were prepared in this study. For a long term and reach prediction, semi-two dimensional sediment transport model, GSTARS, was used. The flood water surface elevations predicted by GSTARS model were analysed statistically and it was concluded that the model is applicable for the South Han River. Three stream tubes is the most suitable to simulate two dimensional river geometric change River geometric changes. For sediment load computation, Ackers and White equation and Yang equation were resonable. River will become narrower regardless of discharge variation, more discharge results in deeper channel.

• Journal of the Korean Institute of Gas
• /
• v.2 no.4
• /
• pp.53-59
• /
• 1998

Flow pattern of air-water two phase flow depends on the conditions of pressure drop, void fraction, and channel geometry. Drag reduction in the two phase flow can be applied to the transport of crude oil, phase change systems such as chemical reactor, pool and boiling flow, and to present cavitation which occurs in pump impellers. But the research on drag reduction in two phase flow is not intensively investigated. Therefore, experimental investigations have been carried out to analyze the drag reduction produced and void fraction by Co-polymer(A611p) addition in the two phase flow system. We find that the maximum point position of local void friction moves from the wall of the pipe to the center of the pipe when polymer concentration increases. Also we find that the polymer solution changes the characteristics of the two phase flow. And then we predict that it is closely related with the drag reduction.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.9
• /
• pp.969-974
• /
• 2011

A carbon nanotube (CNT) is a cylindrical carbon nanostructure with good transport properties along the tube's axis. As an approach for realizing the practical use of CNTs, CNT networks are fabricated and their applications in many fields are investigated. To fabricate thin CNT-based films, several methods have been proposed and used. Among these methods, the spray coating method is a robust method for fabricating a large area. However, it is difficult to achieve uniformity in the CNT network. To solve this problem, it is necessary to understand the effect of the sprayprocess parameters on the deposition thickness distribution. In this study, a numerical model for predicting the deposition thickness distribution during the spray process was developed. The spatial deposition thickness distributions obtained according to various nozzle paths were analyzed using the developed numerical model.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2010.05a
• /
• pp.5.1-5.1
• /
• 2010

One of the most important environmental problems is global warming. Global warming is caused by increase in the amounts of water vapor, methane, carbon dioxide and other gases being released into the atmosphere as a result of the burning of fossil fuels. It has thus become important to reduce fossil fuel use. Environmentally friendly preparation of functional materials has, therefore, attracted much interest for environmental problems. Furthermore, nature mimetic processes are recently been of great interest as environmentally friendly one. There have been many studies on fabrication of various functional nanocrystals. Among various nanocrystal fabrication techniques, flux growth is an environmentally friendly, very convenient process and can produce functional nanocrystals at temperatures below the melting points of the solutes. Furthermore, this technique is suitable for the synthesis of crystals having an enhedral habit. In flux growth, the constituents of the materials to be crystallized are dissolved in a suitable flux (solvent) and crystal growth occurs as the solution becomes critically supersaturated. The supersaturation is attained by cooling the solution, by evaporation of the solvent or by a transport process in which the solute is made to flow from a hotter to a cooler region. Many kinds of oxide nanocrystals have been grown in our laboratory. For example, zero- (e.g., particle), one- (e.g., whisker and tube) and two-dimensional (e.g., sheet) nanocrystals were successfully grown by flux method. Our flux-growth technique has some industrial and ecological merits because the nanocrystal fabrication temperatures are far below their melting points and because the used reagents are less harmless to human being and the environment.

• Journal of Chest Surgery
• /
• v.19 no.3
• /
• pp.421-428
• /
• 1986

From January 1981 through December 1985, 481 thoracic civilian injuries were reviewed in the Department of Thoracic Surgery, Paik Hospital in Seoul. Sixty two percent of the injuries were caused by traffic accident, 18% fall down, 15% blunt trauma, 2% crushing injury, 2% stab wound, and 0.4% gunshot wound. Peak incidence of the trauma victim was fourth and fifth decades revealing 22% and 27% respectively. Sex ratio was 3.5:1 with male predominance. Elapsed time before admission was less than one hour in 36% and one to six hour in 30%. The types of the injuries were as follows: Non-penetrating injuries were the most part of the wounded, 97.6%. Rib fracture was the most common lesion occupying 292 patient out of 481 [61%]. Of these 292 patients, 72% was multiple rib fracture. The incidence of hemothorax or hemopneumothorax was 19% [102 patients] [Table 4]. Most common associated condition was head injuries, 98 patients [14%]. Thoracoabdominal injuries were seen in 31 patients [0.6%]. Tube thoracostomy was the definitive measures in the 20% of the wounded. Open thoractomy was performed in 5%. Additional procedures for the associated condition were done in the 16% of the cases, for example, reduction of long bone fracture and trephination for the head injury. Among 481 wounded, fatal complication occurred in 13 patients [2.7%]. This paper has also compared two series of patients according to period; one from 1970 to 1980 and the present series [Table 8]. Conclusively, the fatal complications or trauma death may be reduced by the effort 1] rapid transport of the victim, 2] initial correction or resuscitative measures of the circulatory and ventilatory deficit 3] early decision of definitive thoracostomy or thoracotomy and 4] proper prioritizing for the care of the multiple critically injured patient.

• Nuclear Engineering and Technology
• /
• v.43 no.3
• /
• pp.301-308
• /
• 2011

The diametral creep of pressure tubes (PTs) in CANDU (CANada Deuterium Uranium) reactors is one of the principal aging mechanisms governing the heat transfer and hydraulic degradation of the heat transport system (HTS). PT diametral creep leads to diametral expansion, which affects the thermal hydraulic characteristics of the coolant channels and the critical heat flux (CHF). The CHF is a major parameter determining the critical channel power (CCP), which is used in the trip setpoint calculations of regional overpower protection (ROP) systems. Therefore, it is essential to predict PT diametral creep in CANDU reactors. PT diametral creep is caused mainly by fast neutron irradiation, temperature and applied stress. The objective of this study was to develop a bundle position-wise linear model (BPLM) to predict PT diametral creep employing previously measured PT diameters and HTS operating conditions. The linear model was optimized using a genetic algorithm and was devised based on a bundle position because it is expected that each bundle position in a PT channel has inherent characteristics. The proposed BPLM for predicting PT diametral creep was confirmed using the operating data of the Wolsung nuclear power plant in Korea. The linear model was able to predict PT diametral creep accurately.

• Journal of Korean Society for Quality Management
• /
• v.47 no.3
• /
• pp.437-451
• /
• 2019

Purpose: The purpose of this study is to improve the quality of the PGM system by improving the structure and production process of slip-ring rotary joint for radar. Methods: The improvement measures for each cause are established through failure analysis of broken items. Specifically, changing in the housing to improve the heating system. Changing the transportation method to prevent damage to equipment during transport. Changing work process of the attenuator ring to prevent damage. etc. Results: The results of this study are as follows; improving the heating system reduces heat generated by the attenuator by about 7 degrees and obtain additional temperature margins. Reduction of defect rate because of adding X-band rotary joint run-out measurement test, ESS of slip-ring rotary joint and Transportation improvement(reinforced flight boxes, tube protection, etc). Getting stable VSWR values by improving work process of attenuator overheating due to a bad bonding process. Conclusion: Through this study, improvements were made to slip-ring rotary joint that failed repeatedly for various reasons. As a result of the application of the improvements, the same fault does not occur until now, so we can see that the quality of PGM has improved.

• Journal of the Korean Society of Radiology
• /
• v.16 no.5
• /
• pp.527-536
• /
• 2022

The radiation shielding characteristic of neutron shielding material has been studied as the preliminary study in order to design cosmic-ray shielding material. Specially, Soft Magnetic Material, known to be effective in EMP and radiation shielding, has been investigated to check if the material would be applicable to cosmic-ray shielding. In this work, thermal neutron shielding experiment was conducted and the Monte Carlo N-Particle(MCNP) was applied to employ skymap.dat, which is cosmic-ray data embedded in MCNP. As a result, polyethylene, borated polyethylene, and carbon nano tube, containing carbon or hydrogen, have been found to be effective in reduction of neutron flux below 20 MeV (including thermal, epithermal, evaporation). In contrast, the materials composed of iron such as SS316 and Soft Magnetic Material show a good shielding performance in the cascade energy range (above 20 MeV). Since Soft Magnetic Material is consisting of 13% of boron, it can also decrease thermal neutron flux, so it is expected that it would show a significant reduction on the entire range of neutron energy if the Soft Magnetic Material is used with hydrogen and carbon, so called low Z material.

• Journal of the Korean Geotechnical Society
• /
• v.37 no.12
• /
• pp.107-116
• /
• 2021

In this study, a set of laboratory liquefaction test has been conducted using undisturbed samples collected from Songlim-park, Pohang where liquefaction phenomenon had been observed in 2017. Soil samples were frozen right after tube sampling to minimize the disturbances during transport, storage, and test preparation. Cyclic triaxial test has been carried out to evaluate the liquefaction resistance ratio of undisturbed soil samples. As a result, the liquefaction resistance ratio of samples collected from 8.0~8.8 m and 11.0~11.8 m were almost similar, and these values were approximately 0.04~0.07 larger than values estimated by simplified assessment method using field test results. It is expected that the application of undisturbed sample for the evaluation of liquefaction resistance could contribute to the economical design of geotechnical structures.