• Journal of Biosystems Engineering
• /
• v.40 no.4
• /
• pp.409-416
• /
• 2015

Purpose: This study evaluates a new banana bulk packaging method under the real transport conditions of Sri Lanka. Methods: A field evaluation of optimized 8-mm thick Styrofoam sheets used as the cushioning material was applied. A trial transport was conducted from Thambuttegama to Colombo using a medium-sized open truck, with banana leaves as the control material. Data were recorded at the farmer, transporter, retailer, and consumer stages of the supply chain. Mechanical damage, physiological loss in weight, fruit firmness, total soluble solids, ripeness index, visual quality ratings, and the physical damage index of the bananas were measured at each stage. A cost-benefit analysis was also conducted for both packaging methods. Results: The 8-mm styrofoam sheets significantly reduced (p < 0.05) the mechanical damage from 26.3% to 12.9% compared to the conventional method for long-distance transport, and the physiological loss in weight showed a decrease of 2.88%. The loss of firmness of the fruits followed a simmilar pattern for both methods until reaching the retailer, but at the consumer was significantly higher (p < 0.05) for the control. However, the physical damage index at the retail stage for the control showed symptoms of physical injury, whereas the bananas transported using the cushioning materials exhibited only minor symptoms. Further, the visual quality of the fruits after transport from the farmer to the consumer was preserved, which is one of the main factors affecting consumer preference and retail price. The proposed method increases the profit margin by 51.2% for Embul bananas owing to the reduced postharvest losses. Conclusion: The 8-mm thick Styrofoam sheets reduced the physical damage to the bananas, with the quality parameters maintained at the prefered level. Moreover, profits may be increased.

• International Journal of Highway Engineering
• /
• v.17 no.6
• /
• pp.37-45
• /
• 2015

PURPOSES : The purpose of this study is to validate the design criteria of the concrete modular road system, which is a new semi-bridge-type concept road, through a comparison of numerical analysis results and actual loading test results under static axial loads. METHODS : To design the semi-bridge-type modular road, both the bridge design code and the concrete structural design code were adopted. The standard truck load (KL-510) was applied as the major traffic vehicle for the design loading condition. The dimension of the modular slab was designed in consideration of self-weight, axial load, environmental load, and combined loads, with ultimate limit state coefficients. The ANSYS APDL (2010) program was used for case studies of center and edge loading, and the analysis results were compared with the actual mock-up test results. RESULTS : A full-scale mock-up test was successfully conducted. The maximum longitudinal steel strains were measured as about 35 and 83.5 micro-strain (within elastic range) at center and edge loading locations, respectively, under a 100 kN dual-wheel loading condition by accelerating pavement tester. CONCLUSIONS : Based on the results of the comparison between the numerical analysis and the full-scale test, the maximum converted stress range at the edge location is 32~51% of the required standard flexural strength under the two times over-weight loading condition. In the case of edge loading, the maximum converted stresses from the Westergaard equation, the ANSYS APDL analysis, and the mock-up test are 1.95, 1.7, and 2.3 times of that of the center loading case, respectively. The primary reason for this difference is related to the assumption of the boundary conditions of the vertical connection between the slab module and the crossbeam module. Even though more research is required to fully define the boundary conditions, the proposed design criteria for the concrete modular road finally seems to be reasonable.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.309-313
• /
• 2006

Many researchers have studied on the lightness of automobile. These researches are such as a body shell, sub frame, fuel tank, engine etc. The transmission Part is a magnitude one in the aspect of weight. A drive shaft (propeller shaft) transmits the engine power to rear differential gear assembly. It is used in the compact car that is a single drive shaft. But in the case of long body cars such as SUV (Sports Utility Vehicle), truck and large vehicle, two or three divided drive shaft are used to prevent the vibration damage from a drive shaft that has been taken high torsion and rotation. This multi-divided drive shaft structure is so heavy because it is assembled by yoke, center bearing and solid spline axis. When the rear axle move up and down, the spline shaft adjust the variation of a length between the transmission and rear axle gearbox. In this paper, it is studied in the experimental method that is a bending vibration characteristic of slip in tube shaped propeller shaft. This type propeller shaft is developed to combine the spline axis with drive shaft and can be light in weight of transmission part.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.22 no.2
• /
• pp.8-15
• /
• 2018

Hollow Core Slab is a very efficient system that can reduce weight and its use has increased. Void slab is a concrete slab that has voids substituted with void material. Because of its saved volume of concrete, void slab can reduce weight of slabs. Also, it can't only save concrete but also can reduce carbon-emission. However, because of the unclear bearing strength at the part of void substituted with voiding material, several problems occur in constructing field. In this study, void slab including void material was built and local bearing strength test was carried out for 3 types of load(truck load, support load and Jack support load). As a result, bearing strength of void neck and upper void material is more than allowable load. And also, bearing strength of specimens with using deck and not using deck are also over allowable loads.

• Korean Journal of Agricultural Science
• /
• v.49 no.4
• /
• pp.927-936
• /
• 2022

The effects of seasonal differences and crating densities on the preslaughter losses, breast meat quality, and physiological indices of broilers were determined. A total of 600 broilers aged 35 days were divided into 10 treatment groups based on five crating densities (10.3, 11.5, 12.8, 14.1, 15.4 birds·m^-2) with two seasons (i.e., summer and winter) to give six replicates and were placed at various locations in the truck. The birds were transported in crates having dimensions of 1.0 m × 0.78 m × 0.26 m. The transportation distance was 20 km for 40 minutes (average 30 - 50 km·h^-1) during the early morning. The results revealed that broilers transported at densities of 14.1 and 15.4 birds·m^-2 recorded lower (p < 0.05) pH, water-holding capacity (WHC), and muscle redness compared to those at densities of 11.5 birds·m^-2. Furthermore, higher (p < 0.05) cooking loss was found in birds stocked at more than 14.1 birds·m^-2 compared to the other treatments. However, no effect (p > 0.05) with different crating densities on body weight loss, carcass traits, glucose, lactate, or muscle yellowness was observed. Crating density of 14.1 birds·m^-2 showed lower (p < 0.05) cortisol contents compared with birds at 10.3 and 15.4 birds·m^-2. Winter transportation had higher (p < 0.05) relative breast meat weight, cooking loss, muscle redness, and cortisol contents whereas summer transportation had higher (p < 0.05) glucose and lactate contents in the blood plasma of broilers. In conclusion, the stocking of 12.8 birds·m^-2 is recommended to minimize stress responses and undesirable changes that could negatively affect muscle quality.

• Journal of Korean Society of Transportation
• /
• v.24 no.5 s.91
• /
• pp.35-44
• /
• 2006

Acceleration and deceleration curves have been used for design purposes worldwide. The curve in design level has been regarded as an single deterministic curve to be used for design of climb lanes. It should be noted that the curve was originally made using ideal driving truck and that the curve is applied during design based on the assumption of no difference between ideal and real driving conditions. However. observations show that aged vehicles and lazy behavioring drivers nay make lower performance of vehicles than the ideal performance. The present paper provides the results of truck speeds at climbing lanes then probabilistic variation of acceleration and deceleration corves. For these purposes. a study about identification of vehicle makers, and weights for trucks at freeway toll gates and then observation of vehicle-following speed were performed. The 85%ile results obtained were compared with the deterministic performance curves of 180, 200, and 220 Ib/hp. It was identified that the performance of 85%ile results obtained from vehicle-following-speed observations were lower than one from deterministic performance curves. From these results, it may be concluded that at the beginning Point of climbing lanes additional $16.19{\sim}67.94m$ is necessary and that at the end point of climbing lanes $53.12{\sim}103.24m$ of extension is necessary.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.10 no.6 s.52
• /
• pp.1-8
• /
• 2006

This paper describes the procedures developing the algorithm for analyzing signals acquired from the Bridge Weigh-in-Motion (BWIM) system installed in Seohae Bridge as a part of the bridge monitoring system. Through the analysis procedure, information about heavy traffics such as weight, speed, and number of axles are attempted to be extracted from time domain strain data of the BWIM system. One of numerous pattern recognition techniques, artificial neural network (ANN) is employed since it can effectively include dynamic effects, bridge-vehicle interaction, etc. A number of vehicle running experiments with sufficient load cases are executed to acquire training and/or test set of ANN. Extracted traffic information can be utilized for developing quantitative database of loading effect. Also, it can contribute to estimate fatigue lift or current health condition, and design truck can be revised based on the database reflecting recent trend of traffic.

• International Journal of Safety
• /
• v.3 no.1
• /
• pp.27-31
• /
• 2004

Some of the petroleum products contain benzene which is well known as a confirmed human carcinogen. For example, gasoline products contain benzene ranging up to several percents by weight. High exposures to the benzene and other organic solvents would be likely to occur during intermittent tasks and or processes rather than continuous jobs such as sampling, repair, inspection, and loading/unloading jobs. The work time for these jobs is various. However, most of work time is very short and the representative time interval is 15 minutes. Thus, it is preferable to do exposure assessment for 15 minute time weighted average which is known as a short time exposure level(STEL) by ACGIH rather than for 8-hours TWA. It is particularly significant to the exposure monitoring for benzene since it has been known that the exposure rate plays an important role to provoke the leukemia. Due to the large variations, a number of processes/tasks, the traditional sampling technique for organic solvents with the use of the charcoal and sampling pumps is not appropriate. Limited number of samples can be obtained due to the shortage of sampling pumps. Passive samplers can eliminate these limitations. However, low sampling rates resulted in collection of small amount of the target analysts in the passive samplers. This is originated the nature of passive samplers. Field applications were made with use of passive samplers to compare with the charcoal tube methods for 15 minutes. Gasoline loading processes to the tank lorry trucks at the loading stations in the petroleum products storage area. Good agreements between the results of passive samplers and those of the charcoal tubes were achieved. However, it was found that special cautions were necessary during the analysis at very low concentration levels.

• Asian-Australasian Journal of Animal Sciences
• /
• v.22 no.8
• /
• pp.1124-1132
• /
• 2009

A trial was conducted to study the effect of supplemental chromium (Cr) levels from a Cr-yeast source on performance, digestibility and carcass characteristics of transport-stressed lambs. Forty-eight Naemi lambs (avg. BW 31.7 kg) were transported by truck for a distance of 1,450 km. On arrival day, the lambs were randomly allocated to four groups receiving diets supplemented with 0.0, 0.3, 0.6 or 0.9 ppm Cr. Each group consisted of four separately housed replicates of three lambs each. The lambs were fed their respective diets ad libitum for 84 d (21 d stress period, followed by 63 d growing period). Road transit of lambs resulted in a decreased (p<0.001) live body weight of 8.5%. Supplementation of Cr-yeast did not alter the performance of lambs during the stress period. Linear and quadratic increases (p<0.05) were observed in DMI and ADG, respectively, with increasing supplemental Cr levels in the diets during the growing period. Values were greater (p<0.05) by 14.7% and 20.8%, respectively, for lambs fed 0.3 ppm Cr compared to control, while those fed on the other two levels were intermediate. Over the 84-d feeding period, a trend was noted towards a slight increase in loin eye area and a decrease in body wall fat thickness for lambs fed Cr supplementation compared to the control group. This study suggests that the supplementation of Cr-yeast, especially at 0.3 ppm level, is beneficial for improving the performance of growing lambs whether the animals are stressed or not.

• Food Science and Preservation
• /
• v.14 no.1
• /
• pp.109-112
• /
• 2007

Precooling and improved packing of mushrooms were investigated with a view to prolonging their freshness. Harvested mushrooms were precooled by forced air cooling and then packed in an EPS container. Mushrooms were transported to customers by insulated truck and stored at either $10^{\circ}C\;or\;25^{\circ}C$. Conventionally packed mushrooms in cartons were also examined as controls. Mushroom respiration rate slowly fell 2- to 3-fold upon precooling. Weight loss was decreased by precooling and the use of the insulated pack. Also, the L-value of the mushroom surface remained high with precooling, and mushroom elongation was less than in the control. Summer market life was extended to 3-4 days (from 1-2 days) by the improved distribution method.