• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.262-267
• /
• 2007

In this paper, we study about wear properties for the metal matrix composites fabricated by low pressure infiltration process. Metal fiber preform reinforced aluminum alloy composite were fabricated by low pressure casting process under 0.4MPa. Infiltration condition was changed the pressure infiltration time of 1 s, 2 s and 5 s under a constant pressure of 0.4MPa. The molten alloy completely infiltrated the FeCrSi metal perform regardless of the increase in the pressure acceleration time. However, the infiltration time at the pressure acceleration time of 1s was shorter than at the pressure acceleration time of 2s or 5s. The FeCrSi/A366.0 composite was investigated the porosity. The porosity is reducing as the pressure acceleration time compared with the pressure acceleration time of 2s and 5s. The FeCrSi/A366.0 composites were investigated the wear resistance. FeCrSi/A366.0 composite at pressure acceleration time of 1s has excellent wear resistance.

• 한국철도학회논문집
• /
• 제12권1호
• /
• pp.72-80
• /
• 2009

소형 다이나모 시험기를 이용하여 4종류의 금속계 소결마찰재와 내열합금 디스크간의 마찰특성을 평가하였다. 고속철도용 소결마찰재는 항공기용 소결마찰재 보다 높은 마찰계수와 마찰계수 안정성을 나타내며, 마모량도 적었다. 또한, 동합금 기지 마찰재는 철계 기지 마찰재보다 마찰면의 온도가 급격히 상승하면 냉각도 빨리 이루어졌다. 시험 후 모든 마찰면에서 Fe 기지의 산화피막이 형성되었고, 산회피막에 따라 마찰특성이 달라졌으며, 마찰면에서는 정상마 모분이 일부가 마찰면 단차부에서 트랩되는 것을 확인하였다.

• Tribology and Lubricants
• /
• 제11권5호
• /
• pp.40-46
• /
• 1995

This study concerns the design and development of the non-vibrating capacitance probe which could be used as a non-contact sensor for tribological wear. This device detects surface charge through temporal variation in the work function of a material. Experiments are performed to demonstrate the operation of the probe on a roating aluminum shaft. The reference electrode of the probe, made of lead, is placed adjacent (< 1.25-mm distance) to the shaft. Both surfaces which are electrically connected, form a capacitor. An artificial spatial variation in the work function is imposed on the shaft surface by coating a segment along the shaft circumference with a colloidal silver paint. As the shaft rotates, the reference electode senses changing contact potential difference with the shaft surface, owing to compositional variation. Temporal variation in the contact potential difference induces a current through the electrical connection. This current is amplified and converted to a voltage signal by an electoronic circuit with an operational amplifier. The magnitude of the signal decreases asymptotically with the electrode-shaft distance and increases linearly with the rotational frequency. These results are consistent with the theoretical model. Potential applications of the probe on wear monitoring are proposed.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2001년도 제34회 추계학술대회 개최
• /
• pp.96-102
• /
• 2001

plasma-sprayed Cr$_2$O$_3$-based coatings containing MoO$_3$ were studied to gain a better understanding of the influence of MoO$_3$ composition in the coatings on their tribological behaviour. A reciprocal type tribo-tester was employed to examine friction and wear behavior of the specimens at high temperature(450。C). The physical characteristics of worn surfaces were investigated by scanning electron microscopy and chemical composition of the coating surfaces was analyzed using a X-ray photoelectron spectrometer. The results showed that friction coefficient of the MoO$_3$-added coatings were lower than those without MoO$_3$ addition. The larger protecting layers were observed at the worn surface of plasma spray coated specimens with MoO$_3$ addition. XPS analysis of the protecting layer indicated that MoO$_3$ composition was dominantly formed at the surface. MoO$_3$ composition in the protecting layer appears to be more favorable in reducing the friction.

• Journal of Welding and Joining
• /
• 제18권5호
• /
• pp.98-104
• /
• 2000

Aluminum alloys are being employed in automobile parts as strive to reduce overall vehicle weight to meet demands for improved fuel economy and reduction in vehicle emissions. Al-based composites reinforced with ceramic ($Al_2O_3,\;SiC,\;TiC\;and\;B_4C$) applications in a variety of components in automotive engines, such as liners, where the tribological properties of the material are important. In this study, Al-base composites reinforced with TiC particle powders has been developed for producing plasma spray coatings. The composite plasma spray powders were prepared Al-13Si-3Mg(wt%) alloy with TiC(40, 60 and 80wt%) particles ($0.2~5{\mu}textrm{m}$) by drum type ball milling. The composite powders ($36~76{\mu}textrm{m}$) were sprayed with plasma torch. Plasma sprayed coatings were heat-treated at $500^{\circ}C$ for 3 hours. The wear resistances of the plasma sprayed coatings were found to decrease with increasing TiC content and improved with heat treatment. AlSiMg-40% TiC heat-treated coatings were showed the best wear resistance in this study.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.1
• /
• pp.231-234
• /
• 2004

Chemical mechanical polishing(CMP) process was studied in terms of tribology in this paper. CMP performed by the down force and the relative motion of pad and wafer with the slurry is typically tribological system composed of friction, wear and lubrication. The piezoelectric quartz sensor for friction force measurement was installed and the friction force was detected during CMP process. Various coefficient of friction was attained and analyzed with the kind of pad, abrasive and the abrasive concentration. The lubrication regime is also classified with ${\eta}v/p(\eta,\;v\;and\;p;$ the viscosity, relative velocity and pressure). Especially, the co-relation not only between the friction force and the removal per unit distance but also between the coefficient of friction and within-wafer-nonuniformity was estimated.

• Tribology and Lubricants
• /
• 제27권6호
• /
• pp.321-325
• /
• 2011

Nanodiamond was dispersed in paraffin liquid oil to investigate the effects of nanodiamond at the marginally lubricated condition. Scuffing test and immediate loading sliding wear test were conducted using the fabricated nanodiamond oil. As a result, dispersion of nanodiamond in oil leads to increase in scuffing life, and nanodiamond contents affects the scuffing life. In case of immediate loading sliding wear test, the result was different according to hardness of specimen. If hardness of specimen was low, abrasion of nanodiamond occurred actively. If hardness of specimen was increased, however, nanodiamond can act as a spacer or rolling between contacting surfaces.

• International Journal of Ocean System Engineering
• /
• 제3권3호
• /
• pp.147-151
• /
• 2013

This study was to correctly estimate the friction and wear behavior of carbon fiber and PEEK sheet composites, and the validity of using them as alternatives to the metal-based materials used for artificial hip joints. Moreover, this work evaluated the friction coefficient according to the fiber ply orientation, along with the fractured surfaces of the carbon/PEEK composites. The unidirectional composites had higher friction coefficients than those multidirectional composites. This was caused by the debonding between the carbon fiber and the PEEK sheet, which was proportional to the contact area between the sliding surface and the carbon fiber. The friction test results showed that there was no significant differences in relation to the fiber ply orientation. However, in a case where the speed was 2.5 m/s, the friction coefficient was relatively large for configuration I. The friction surface of the specimen was analyzed using an electron microscope. In all cases, the debonding of the fiber and PEEK could be confirmed.

• 대한기계학회논문집A
• /
• 제37권2호
• /
• pp.219-225
• /
• 2013

본 연구에서는 무전해 도금 코팅방법을 이용하여 생성한 Ag 박막의 기계적 특성을 고찰하였다. 이 코팅방법은 화학적 반응을 통해 금속박막을 기판 위에 형성할 수 있는 공정으로써 비교적 간단하고 경제적이며 전기도금과 비교했을 때 도체뿐만 아니라 부도체에도 적용할 수 있다는 유리한 장점이 있다. 따라서 반도체에서부터 기계부품에 이르기까지 산업전반에 걸쳐 다양하게 적용되고 있는 코팅방법이다. 본 연구에서는 무전해 도금 공정의 변수에 따라 형성되는 Ag 박막의 기계적 특성을 파악하는데 중점을 두었다. 특히, 무전해 도금방법을 이용해 제작한 코팅 시편에 대해 도금시간에 따른 거칠기 및 두께에 대한 분석을 실시하였으며 AFM, SEM, Tribotester 와 같은 장비를 이용하여 트라이볼로지적 특성을 규명하였다.

• 한국결정성장학회지
• /
• 제13권1호
• /
• pp.36-40
• /
• 2003

$CH_4/(C_2H_5O)_4Si/H_2$/Ar가스 혼합물을 출발 반응원료로 하여 플라즈마 화학기상증착법으로 Si 기판 위에 유사 다이아몬드 나노복합체(diamond-like nanocomposite, DLN) 박막을 증착하였다. 성장된 막의 화학구조와 미세구조를 확인하였으며 막의 마모특성을 평가하였다. 증착된 DLN 막은 다이아몬드와 유사한 a-C:H 구조와 실리카와 유사한 a-Si:O 구조가 네트워크 형태로 구성되어 있음을 확인하였으며 극도로 낮은 마모계수와 마모속도를 나타내어 내마모 코팅용 보호막으로 의 응용에 적합한 것으로 나타났다.