• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2016.05a
• /
• pp.239-241
• /
• 2016

The success or failure of businesses affected by the decision makers, when good decisions go in the direction of social development, the ability to be more successful, while one bad decision away contrary to the trend of social development are less likely to succeed. Today AHP method is widely used to solve critical problems in many areas of life. Analytic Hierarchy Process (AHP) is a quantitative comparison method is used to select a preferred solution using comparable pairs of solutions based on their relative effectiveness against criteria. The purpose of this study is provide an overview of the application of hierarchical analysis methods to solve many different important issues in the field of supply chain management.

• Journal of Information Display
• /
• v.12 no.3
• /
• pp.129-134
• /
• 2011

The universal current reversal method is used for the simultaneous measurement of response time (${\tau}$), azimuthal angle (${\varphi}_o$), spontaneous polarization ($P_S$), and rotational viscosity (${\gamma}_{\varphi}$) of two ferroelectric liquid crystals (FLCs). The application of AC field in FLCs results in reorientational current, which is further analyzed to obtain various parameters. The variation in the parameters with temperature follows the typical trend predicted by the theory. The theoretical curve fits well into the experimental data. Its comparison with traditional current reversal method is confirmed to address certain limitations of that method.

• Korean Management Science Review
• /
• v.32 no.1
• /
• pp.133-145
• /
• 2015

Motion picture industry in Korea has been growing constantly and aroused various kinds of research attention. Particularly, the introduction of official box-office database service brought quantitative studies. However, approaches based on diffusion models have been rarely found with domestic film markets. In addition to the fundamental statistical review on Korea and US film markets, we applied a diffusion model to daily box-office revenue. Unlike conventional preference of Gamma distribution on the film markets, estimation results proved that BMIC can also explain the trend of daily revenue successfully. The comparison with BMIC showed that there is a distinctive difference in diffusion patterns of Korea and US film markets. Generally, word-of-mouth effect appeared more significant in Korea.

• Journal of Korean Society for Quality Management
• /
• v.24 no.1
• /
• pp.110-125
• /
• 1996

Since 1975, Korean defence quality system has been operated by adopting defence specifications, 0050-0015, 0050-0029 and 0050-0030, which were based on the American specifications, MIL-Q-9858, MIL-Q-45208 and MIL-STD-45662. The trend that the ISO certification is intensively required for the international trade, and the need for modernization of the Korean military forces, however, provide motivation to revise the defence quality system. In this study, an improved defence quality system has been proposed by the comparison study among the requirements prescribed in ISO 9000, AQAP 100 series, MIL-Q-9858.

• Proceedings of the KIEE Conference
• /
• 1992.07b
• /
• pp.633-636
• /
• 1992

The need for more efficient transformer core materials, due to increased recognition by the loss reduction of electric utilities, has spurred the development of amorphous metal usage in transformer. The loss of amorphous core is one third to one fourth that of silicon steel at equivalent inductions 15KG and below. Thus, the substitution of amorphous metal for conventional silicon steel in a transformer core can reduce core loss by 75%. This paper describes the development trend, the manufacturing processes of amorphous core transformer and the characteristics of amorphous core transformer in comparison with those of silicon core transformer.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.10
• /
• pp.44-51
• /
• 2006

According to global trend of the expanding need of high-quality automobiles, the usage of small precise worm consisting of gearing part for motors to actuate convenience modules has increased rapidly. Precision of those worms has very sensitive characteristic to motor performance and noise. Forming process has been generally used to manufacture worms because of its mass productivity. However, it has problems such as deformation due to residual stress and wear of dies. Planetary milling and side milling are among alternatives using cutting tools. To overcome those problems the two machining methods have some contrast features in the sense of tool numbers and cutting mechanism. In this paper, machinability of both methods was compared in terms of cutting force, precision and cycle time.

• Journal of the Korean Society of Industry Convergence
• /
• v.3 no.1
• /
• pp.3-8
• /
• 2000

This paper describes a development of self tuning scheme for PI and PO type fuzzy controllers. The output scaling factor(SF) is adjusted on-line by fuzzy rules according to the current trend of the controlled process. The rule-base for tuning the output SF is defined on error and change of error for the controlled variable using the most natural and unbiased membership functions. Simulation results demonstrate the better control performance can be achieved in comparison with Ziegler-Nichols(Z-N) PID controllers.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.19 no.6
• /
• pp.1149-1157
• /
• 1994

In this case of the mobile communication of vehicles with satellite, the signal at attenuation is due to roadside trees. To analyze this signal attenuation, a roadside tree was modeled as different obstacles of rectangular type and then using Fresnel and Kirchhoff diffraction theory, a formula was derived for signal intensity variation caused by the roadside tree model. The signal attenuation of a roadside tree model was obtained by numerical analysis with variation of the elevation angle, the position and distance between a receiver and a transmitter, and these were compared with experimental results. The results of comparison between theoretical and experimental values show, as expected, the good agreement of the signal attenuation trend.

• Journal of Communications and Networks
• /
• v.8 no.1
• /
• pp.106-115
• /
• 2006

The current trend toward the utilization of the Internet as a common means for the offer of heterogeneous services imposes to address the issues related to end-to-end service assurance in the inter-domain scenario. In this paper, we first present an architecture for service management in networks based on service level specifications (SLS). The architecture is designed to be independent both of the specific network technology adopted and of the high level service semantics. Then, we focus on a specific functionality of the proposed architecture: Resource allocation in the multi-domain scenario. A distributed admission control algorithm is introduced, its complexity is evaluated and a comparison with related solutions is provided.

• Journal of Welding and Joining
• /
• v.19 no.5
• /
• pp.540-547
• /
• 2001

This study has evaluated the wear behavior of PTA (Plasma Transferred Arc) Inconel 625 and Stellite 6 overlays on Nimonic 80A substrate. Nimonic 80A alloy was also included for comparison. In order to evaluate the wear performance, three-body abrasive wear test and pin-on-disk dry sliding wear test were performed. Microstructural development during the solidification of deposits is also discussed. Wear test results show that the wear rate of Stellite 6 deposit is lower than that of Inconel 625 deposit and Nimonic 80A. The sliding wear resistance of overlay deposits follows a similar trend to the abrasive wear resistance, but for Nimonic 80A. The main wear mechanisms were abrasive wear for Inconel 625 deposit, adhesive wear and delamination for Stellite 6 deposit in pin-on-disk dry sliding wear test and ploughing in three-body abrasive wear test. Cross sectional examinations of the worn surface of pin specimens after pin-on-disk dry sliding wear test implies that the plastic deformation near worn surface has occurred during the wear testing.