• 열처리공학회지
• /
• 제7권4호
• /
• pp.233-243
• /
• 1994

Constitutive relation of thermoelasto-plastic material undergoing phase transformation during quenching process were developed on the basic of continuum thermodynamics. The metallic structure, temperature and residual stresses distributions were numerically calculated by the finite element technique. The metallic structure were defined by transformation from austenite to pearlite and characterized as a fuction of thermal history and mixture rule of phase. On the distribution of thermal stress along the radial direction, axial and tangential stresses are compressive in the surface, and tential in the inner part. Radial stress is tensile in the whole body. The reversion of residual stress takes plase at 11.5~15.5mm from the center.

• 한국세라믹학회지
• /
• 제29권5호
• /
• pp.341-346
• /
• 1992

The effects of CaO addition on the low temperature degradation behavior of 2.5Y-TZP ceramics were investigated. Y2O3-CaO-ZrO2 ceramics were prepared from the commercial Y-TZP powder added within 1 mol% of CaO. Fully tetragonal phase could be obtained at each composition under sintering condition of 1500$^{\circ}C$ for 1 hour. As the amount of CaO increased, grain size was decreased. From the result of heat treatment at 200$^{\circ}C$, volume fraction of monoclinic phase formed on the surface of each specimen was decreased with higher CaO amount. Stability of tetragonal ZrO2 phase for low temperature heat treatment was increased by CaO addition without the degradation of mechanical properties.

• 한국환경과학회지
• /
• 제1권2호
• /
• pp.105.1-113
• /
• 1992

The present study was performed to develop the removal system of the offensive gases, including hydrogen sulfide of acid gas, ammonia or amice of base gas, from the nightsoil treatment plant. In order to remove the offensive gases, the Fe-EDTA system liquid phase catalytic oxidation method with the bubble lift column reactor was employed. From the results obtained, it was confirmed that the offensive gases can be deodorized simultaneously and also hydrogen sulfide of acid gas, ammonia of base gas completely removed at pH 6.45. In addition, as input gases feed rate the efficiency of acid gas did not change but the efficiency of base gases decreased to approximately 90 % at pH 6, 0. From the result of particle size analyzer, it was found that the particle sizes including sulfur and other impurites grew up to $21{\mu}m$ over 72hour reaction time.

• 한국세라믹학회지
• /
• 제43권1호
• /
• pp.1-3
• /
• 2006

Well-shaped NaA zeolite cubic crystals of a large size of $5-7{\mu}m$ were synthesized by a hydrothermal method in a mother solution having a $3.55Na_2O:Al_2O_3:1.6SiO_2:593\~2000H_2O$ composition. Thermal treatment of NaA zeolite crystals resulted in the formation of a crystalline phase of $NaAlSiO_4-Camegeite$ between 800 and $900^{\circ}C$. Even at $1000^{\circ}C,\;NaAlSiO_4$ phase was found as a major product. Environmental Scanning Electron Microscopy (ESEM), High Resolution Transmission Electron Microscopy (HRTEM), X-Ray powder Diffraction (XRD), Fourier Transform Infrared (FT-IR) spectroscopy, and DTA/TGA and BET analyses were used to characterize the initial materials and the obtained products after various heat treatments.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2001년도 The 6th International Symposium of East Asian Resources Recycling Technology
• /
• pp.173-178
• /
• 2001

The materials processing factors such as remelting and casting, heat treatment and microstructure, sheet rolling and can body forming in the aluminum can-to-can recycling procedure have been investigated. Aluminum used beverage can(UBC) was remelted together with virgin aluminum. The ceramic filter was used during casting to remove large impurities. As-cast microstructure was composed of large intermetallic compound (mainly $\beta$ -phase) distributed in the aluminum matrix. By heat treatment, $\beta$ -phase was transformed to $\alpha$ -phase which was also formed from $Mg_2$Si particles. The heat treated ingots were hot-rolled at 48$0^{\circ}C$ and cold-rolled to thin sheets. Can making from this thin sheets was successful and earing was measured after can making. There was a critical cold reduction rate for minimum earing. Some cracks were initiated from the impurity particles which was not removed during filtering.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2010년도 춘계학술발표대회
• /
• pp.40.1-40.1
• /
• 2010

Recently high strength steel sheets with high formability for automotive parts have been being developed to meet the demands for passenger safety and weight reduction of car body. Among these high strength steels, dual-phase steels are regarded as one of the attractive steels due to their excellent mechanical properties including high strength and ductility. However, to be successfully applied to automotive parts they should be corrosion resistant enough to satisfy the required quality of car maker. This also requires their feasibility for galvannealed production including hot dip galvanizability. In this study has been placed on understanding the effects of heat-treatment(austenizing and isothermal treatment) on the microstructures and mechanical properties of a 0.06C-0.03Si-2.0Mn high strength steel for cold forming. The microstructure and phase distribution were examined with eth aids of SEM, EBSD, TEM etc.. Through the study the production of 590MPa grade DP GA steels with good formability and galvaniability were shown to be possible.

• 한국정보처리학회논문지
• /
• 제7권5호
• /
• pp.1351-1360
• /
• 2000

The hand acupuncture, called Sujichim, is mostly conducted at home. Many people try to learn and apply the Sujichim treatment to the health care of their family. This paper proposes a mixed reality scheme for the hand acupuncture supporting system. Using our system, a novice can easily perform the acupuncture by himself to improve his body condition. Our system has two major phases: learning phase and operation phase. In learning phase, we extract the finger joint lines from the real world image, where the lines are very important for finding the acupuncture spots on a hand. In operation mode, user can easily make Sujichim treatment by the knowledge provided by the computer. According to the experiments, our system is proved to be very effective and easy to use.

• Progress in Superconductivity
• /
• 제1권1호
• /
• pp.56-60
• /
• 1999

Ultra fine MgO particles added BSCCO tapes were fabricated by tape casting using Doctor Blade Method and enclosed by silver foil for different starting compositions (that is, 2223 major, 2212 major). In order to obtain optimum microstructure, thermomechanical treatment was done. Microstructure and phase were analyzed by XRD, SEM and DTA. The critical current density was measured under magnetic field at 77K. The tapes fabricated from the precursor powder with BSCCO-2223 phase (>90%) result in a microstructure with a larger grain size and higher transport critical current density value under magnetic field at given thermomechanical treatment conditions.

• 센서학회지
• /
• 제18권6호
• /
• pp.441-448
• /
• 2009

Magnesia partially stabilized zirconia(Mg-PSZ) solid electrolytes for an improvement of thermal shock resistance, which is suitable for the measurement of oxygen activity in a molten steel, were prepared by post-thermal aging treatment. The steelmaking oxygen sensor elements were formed by an injection molding method, sintered at $1650^{\circ}C$, and then thermal aged ranged from 1250 to $1400^{\circ}C$. Sintered density and porosity were decreased as increasing the magnesia content in a zirconia-magnesia solid solution. Fractions of cubic phase to the synthesized Mg-PSZ solid electrolytes were ranged from 13.13 to 79.54.% after post-thermal aging treatment. Very dense microstructure without voids in the grains was obtained by the post-thermal aging process. Fine tetragonal phase crystallites precipitated on the cubic surface during post-thermal aging up to $1300^{\circ}C$ improve a thermal shock resistance and reappearance of electro motive force(EMF) curve.

• Corrosion Science and Technology
• /
• 제5권1호
• /
• pp.1-4
• /
• 2006

Martensitic stainless steel is used when mechanical properties such as high tensile strength and hardness are required. Medium carbon-contained martensitic stainless steel which contains more than 0.2 wt% of carbon should be heat-treated and quenched at the temperature where undissolved carbides are totally dissolved into the matrix. In particular, the dissolution and reprecipitation behaviors of various forms of carbides are affected by such parameters as heating rate, heating temperature, duration time and cooling rate. This study is to investigate the effects of heat treatment parameters of 14Cr-3Mo martensitic stainless on corrosion resistance and phase transformation in relation to the dissolution and reprecipitation of carbides.