• Nuclear Engineering and Technology
• /
• 제52권12호
• /
• pp.2771-2788
• /
• 2020

Experiments are conducted to study bubble flow behavior during the instability of subcooled boiling under uniform and non-uniform transverse heating. The non-uniform heat distribution introduces nonuniform bubble generation and condensation rates on the heated surface, which is different from the uniform heating. These bubble generation and condensation characteristics introduce a non-uniform local pressure distribution in the transverse direction, which creates an extra non-uniform pressure on the flowing bubbles. Therefore, different bubble flow behavior can be observed between uniform and non-uniform heating conditions. In the uniform heating, bubble velocity fluctuations are low, and the bubbles travel straight along the axial direction. In the non-uniform heating, more fluctuation in the bubble velocity occurs at low mass flow rate and high subcooled inlet temperatures, and reverse flow is observed. Additionally, the bubbles show a zigzag trajectory when they pass through the channel, which indicates the existence of cross flow in the transverse direction.

• 상하수도학회지
• /
• 제19권6호
• /
• pp.758-766
• /
• 2005

This study was conducted to evaluate the effect of the transverse troughs on hydrodynamic behavior within the a certain full-scale sedimentation basin (flow rate/one basin; $10,000m^3/d$) using CFD simulation and ADV technique. In order to verify the CFD simulation, we measured the factual velocity at 36 points in the full-scale sedimentation basin, whose outlet structure is inadequate, with ADV technique. Both the CFD simulation and the ADV measurement results were in good accordance with each other. From the CFD simulation results of the existing basin, it was investigated that extreme upward flow occurs in the near of two transverse troughs. It was suspected that since the transverse troughs converted the open channel flow into the local closed pipe flow, the increased pressure in this local closed pipe flow region made the extreme upward flow. For solving this problems, it was suggested to modify transverse-typed launder into finger-typed launder and to install a longitudinal baffle in the center in this study. The CFD simulation results of all suggested amendments told us that the extreme upward flow, had occurred especially in the beneath of transverse troughs, was much less in the case of finger typed launder basin than that in the existing basin. Also, it was predicted that installing a longitudinal baffle made the fully developed flow which is more effective for sedimentation.

• Korea-Australia Rheology Journal
• /
• 제19권1호
• /
• pp.17-25
• /
• 2007

In liquid composite molding (LCM), composites are produced by impregnation of a dry preform with liquid resin. The resin flow through the preform is usually described by Darcy's law and the permeability tensor must be obtained for filling analysis. While the resin flow in the thickness direction can be neglected for thin parts, the resin flow in the transverse direction is important for thicker parts. However, the transverse permeability of the preform has not been investigated frequently. In this study, the transverse permeability was measured experimentally for five different fiber preforms. In order to verify the experimental results, the measured transverse permeability was compared with numerical results. Five different fiber mats were used in this study: glass fiber woven fabric, aramid fiber woven fabric, glass fiber random mat, glass fiber braided preform, and glass/aramid hybrid braided preform. The anisotropic braided preforms were manufactured by using a three dimensional braiding machine. The pressure was measured at the inlet and outlet positions with pressure transducers.

• 한국터널지하공간학회 논문집
• /
• 제20권2호
• /
• pp.305-315
• /
• 2018

본 연구에서는 도로터널의 횡류환기 및 반횡류환기 방식의 설계 방안을 도출할 목적으로 수치해석적인 방법에 의해서 환기특성을 고찰하고 소요환기량과 환기 시스템 용량의 관계를 검토하였으며, 다음과 같은 결과를 얻었다. 급 배기 횡류환기방식에서 환기시스템의 급 배기풍량은 이론적으로 소요환기량과 자연환기량의 차가 되나, 해석결과에 의하면 환기시스템 용량은 소요환기량과 자연환기량의 차보다 약 10%정도 증가하는 것으로 나타나고 있다. 또한 제트팬을 설치하여 종방향 풍속을 증가시키는 경우, 환기시스템의 급배기 풍량은 감소하나, 터널풍속이 증가할 수록 터널 내 농도가 감소하기 때문에 오염물질에 대한 배기효과가 감소하여, 횡류 환기시스템의 용량 감소효과는 감소하는 것으로 나타나고 있다. 급기만 하는 반횡류식에서는 터널입구 풍향이 차량진행방향과 반대인 경우에는 환기시스템의 급기풍량은 소요환기량과 동일하나, 해석결과에서는 약 13.3% 이내의 범위에서 증가하는 것으로 나타나고 있으며, 터널입구 풍속이 음수인 상태에서는 제트팬 댓수를 증가하여 도 환기효과는 기대할 수 없는 것으로 나타났다.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2001년도 춘계학술발표대회 논문집
• /
• pp.176-179
• /
• 2001

When the preform is composed of more than two layers with different in-plane permeability in resin transfer molding, effective average permeability should be determined for the flow analysis in the mold. The most frequently used averaging scheme is the weighted average scheme, but it does not account for the transverse flow between adjacent layers. A new averaging scheme is proposed predicting the effective permeability of the multi-layered preform, which accounts for the transverse flow effect. The new scheme is verified by measuring the effective permeability of the multi-layered preforms and the difference in each flow front position.

• Journal of Mechanical Science and Technology
• /
• 제18권12호
• /
• pp.2258-2264
• /
• 2004

This article described the numerical investigation of shear-thinning blood flow characteristics when subjected to longitudinal and transverse vibrations and delineated the underlying mechanisms of the flow rate enhancements, respectively. In order to fully consider the mechanical vibrations of the capillary, a moving wall boundary condition was adopted. The present numerical results showed that the longitudinal vibration caused a significant increase of wall shear rates, which resulted in a decrease of viscosity and the subsequent increase of flow rates. However, the shear rate for the transverse vibration was slightly increased and the calculated flow rate was underestimated comparing with the previous experimental results.

• 대한기계학회논문집B
• /
• 제33권7호
• /
• pp.495-505
• /
• 2009

A two-dimensional circular cylinder freely falling in a channel has been simulated by using immersed boundary - lattice Boltzmann method (IB-LBM) in order to analyze the characteristics of motion originated by the interaction between the fluid flow and the cylinder. The wide range of the solid/fluid density ratio has been considered to identify the effect of the solid/fluid density ratio on the motion characteristics such as the falling time, the transverse force and the trajectory in the streamwise and transverse directions. In addition, the effect of the gap between the cylinder and the wall on the motion of a two-dimensional freely falling circular cylinder has been revealed by taking into account a various range of the gap size. As the cylinder is close to the wall at the initial dropping position, vortex shedding in the wake occurs early since the shear flow formed in the spacing between the cylinder and the wall drives flow instabilities from the initial stage of freely falling. In order to consider the characteristics of transverse motion of the cylinder in the initial stage of freely falling, quantitative information about the cylinder motion variables such as the transverse force, trajectory and settling time has been investigate.

• 물과 미래
• /
• 제24권1호
• /
• pp.99-107
• /
• 1991

본 연구는 만곡 충적수로의 거친하상(재료의 입경이 2mm이상)에 있어 횡방향 하상경사와 흐름특성을 해석하기 위한 모형을 개발하는데 있다. 질량 보존법칙, 운동량 방정식 및 하상 안정식을 적용하여 만곡 수로의 흐름특성을 수로 중심선에서의 횡방향 하상경사에 관한 일반식으로 유도하고, 그 해를 Sine-generated curve method(SCM)에 의해 구하였으며, 실측치와 비교, 분석하였다. 최대 횡방향 하상경사와 유속분포에 의한 지체 거리(lag distances)는 홍수시 제방의 위협단면을 예측할 수 있을 것이다.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2003년도 추계 학술대회논문집
• /
• pp.126-131
• /
• 2003

A series of computational simulations have been carried out for supersonic flows in a scram jet engine with and without a cavity. Transverse injection of hydrogen, a simplest form of fuel supply, is considered in the present study with the injection pressure varying from 0.5 to 1.5 MPa. The corresponding equivalence ratios are 0.167 - 0.50. The work features detailed resolution of the flow dynamics in the combustor, which was not typically available in most of the Previous studies. In particular, oscillatory flow characteristics are captured at a scale sufficient to identify the underlying physical mechanisms. Much of the flow unsteadiness is related not only to the cavity, but also to the intrinsic unsteadiness in the flowfield. The interactions between shock waves and shear layer may cause a large excursion of flow oscillation. The role of the cavity and injection pressure are examined systematically.

• The Journal of Korean Physical Therapy
• /
• 제29권2호
• /
• pp.69-73
• /
• 2017

Purpose: This study was conducted to investigate the effects of blood flow restriction and different support surfaces for bridge exercises on the thickness of the transverse abdominis and multifidus, which are trunk-stabilizing muscles. Methods: The study's subjects were 45 adults who were divided into three groups that performed bridge exercises over a six-week period on their respective support surfaces after blood flow restriction. Changes in the thickness of the subjects' transverse abdominis and multifidus muscles were measured using ultrasonography before the experiment, then three and six weeks after the experiment. The changes in each variable over time were analyzed using a repeated-measures analysis of variance (ANOVA). Results: The transverse abdominis showed significant differences in muscle thickness with regard to time and the interaction between time and each group (p<0.05), but no significant differences with regard to changes among groups (p>0.05). The multifidus showed significant differences in muscle thickness with regard to time, the interaction between time and each group, and changes between groups (p<0.05). Conclusion: Blood flow restriction and different support surfaces for bridge exercises led to significant differences in the thickness of the transverse abdominis and multifidus. This study's results may be used as the basis for future studies and for rehabilitation in clinical practice.