• Journal of Korean Society of Transportation
• /
• v.26 no.3
• /
• pp.145-153
• /
• 2008

This study proposes a facility location model in consideration of spatial coverage and travel cost as an effort to make objective and effective decisions of natural gas filling stations. The proposed model is developed for fixed stations and consists of two stages. The first stage employs a heuristic algorithm to find a set of locations which satisfy the spatial coverage constraints determined by the maximum travel distance between the filling stations and bus depots. In the second stage, the optimal location of filling stations is determined based on the minimum travel cost estimated by using a modified transportation problem as well as the construction and maintenance costs of the filling stations. The applicability of the model is analyzed through finding the optimal location of filling stations for the city of Anyang, a typical medium-sized city in metropolitan Seoul, based on the demand of natural gas buses. This study is expected to help promote the spread of natural gas buses by providing a starting point of a objective and reasonable methodological perspective to address the filling station location problem.

• Journal of the Korean Society of Safety
• /
• v.32 no.4
• /
• pp.129-136
• /
• 2017

This study investigated the probability of possible accident through qualitative and quantitative analysis of the pressure safety valve types installed in facilities using high pressure gas to compare the installation domestic and foreign pressure safety valve standards sought the safety characteristics and safety improvement direction accordingly. The three types are the case where the shut-off valve is not installed at the front of the PSV (Case A), If a shut-off valve is installed at the front of the PSV for inspection (Case B) and If a shut-off valve is installed in front of PSV (C.S.O), PSV is installed in parallel (Case C). Three types of cases were compared with FTA and HAZOP. The results of study of the possible accidents due to over-pressure safety valve installation type, used in a high-pressure gas facilities was shows in the following order Case B > Case A > Case C. The results of analysis through FTA was in order to protect the reservoir for the possible occurring of accident the safety valve installation is depend on its type. In the FTA analysis, defects in the device itself which attached to the storage tank as a substitute for analysis of the probability of operator mistakes was Case B with as high as $2.01{\times}10^{-6}$. Depending on the type of installation analysis of Case B in order to ensure safety is prohibited to install shut-off valve and believes that mandatory regulations are needed. Rationally installing of pressure safety valve in the high pressure using facilities will be expected to improve the industrial safety from severe accidents such as high-pressure gas fire explosion.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.20 no.2
• /
• pp.76-88
• /
• 2012

In this study, the treatment flow of the recyclables(paper, plastic, metal, etc.) collected and separated from MSW was investigated throughout entire phase from separation and collection to final disposal. Based on the site survey, most recyclables came into six material recovery facilities were comparatively managed well. However, some of recyclables showed irrelatively transportation flow. Because the main income source of the recyclables transportation companies is profit margin between treatment and transportation cost based on economics only therefore, it occurs an unnecessary route and long distance transportation while going to final destination. This unreasonable system should be a serious problem relating establishment of the resource recycling system. As a result of this study, in order to establish the reasonably resource recycling system, recycling center including material recovery facility has to manage the recyclables generated in close range preferentially. Also integrated its treatment system over a wide area will need to be considered as a basic step for the reasonable reasonably resource recycling system.

• Journal of The Korea Institute of Healthcare Architecture
• /
• v.22 no.2
• /
• pp.7-14
• /
• 2016

Purpose: Caring for weak person in society, which increases the population of the elderly and people with disabilities is essential. By increasing along with the increase of the use of passenger facilities for travelers and pedestrian is increasing the demand for convenient and secure facilities for everyone. The emerging importance of the passenger-related facilities, but a representative study of the bus terminal facilities is lacking. Bus terminals are the most popular passenger facility. Thus, the bus terminal can be conveniently used by anyone in everyday life, however, the applied elements considering the use of the transportation Poor are not sufficient. Methods: This study was conducted to evaluate BF certification standards targeting bus terminals across the country to determine the availability of the transportation Poor in bus terminal. Result: As a result of the bus Terminal possibility BF certified it appeared to be very low. Also, items received the lowest rating of each item was evaluated in the informative facilities and items. Bus terminal is a facility used by the unspecified individuals, the proportion of first-time user is high, but there is a lack of consideration for the transportation Poor bus terminals. Implications: In the future, this study can guide the next research on the application of BF certification standards in bus terminal. Further studies can be presented to the improvement of the BF certification indicator in bus terminal.

• Journal of Korean Society of Transportation
• /
• v.27 no.5
• /
• pp.189-194
• /
• 2009

Transfer impedance is one of the most critical factors decreasing the competitive power of public transportation. Therefore, it is necessary to improve transfer impedance of KTX and rail station users in order to increase the usage of public transportation. Important factors influencing transfer decisions include exterior walking distance, interior walking distance, steps, and escalators. However, their comparative impedances are different. This study constructed a model for calculating transfer impedance based on bodily sensational transfer time in KTX and rail stations and calculated transfer impedance on major KTX and rail stations in Korea. The study results show that the addition of one escalator decreases travel time by one to three minutes. The calculated transfer impedance based on bodily sensational transfer time in this study can be utilized as objective criteria to compare transfer conditions of different KTX and rail stations and to prioritize them for facility improvement. The calculated transfer impedance also can be used as facility guidelines for designing a new transit center.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.19 no.6
• /
• pp.134-143
• /
• 2020

With the worldwide spread of African swine fever, interest in livestock epidemics is growing. Livestock transport vehicles are the main cause of the spread of livestock epidemics, but no empirical quarantine procedures and standards related to the mobility of livestock transport vehicles in South Korea. This study extracted livestock-related vehicles' trajectory by utilizing the facility visit history data from the Korea Animal Health Integrated System and the DTG (Digital Tachograph) data from the Korea Transportation Safety Authority and presented them as exposure indexes aggregating the link-time occupancy of each vehicle. As a result, a total of 274,519 livestock-related vehicle trajectories were extracted, and exposure values by link and zone were quantitatively derived. Through this study, it is expected that prior monitoring of livestock transport vehicles and the establishment of post-disaster prevention policies would be provided.

• International Journal of Internet, Broadcasting and Communication
• /
• v.7 no.2
• /
• pp.109-112
• /
• 2015

The Korean electric railway is growing rapidly such as speed of 300km/h in high speed section and 230km/h in the conventional railway section. But, power supply failure occurs because of loss of contact, defective catenary system and high speed vehicle. Therefore preventive maintenance way based reliability has been applied. Typical example is the facility inspection method using trolley inspection system. But it is required differentiated inspection method to prevent problem such as inspection errors. In this paper, a study on the trolley sliding condition inspection system using monitoring techniques is performed for performance enhancement of inspection system. It proposed the efficient maintenance method through monitoring the deviation and height of contact wire after installing inspection system on the top of train which operates in the metropolitan area. Inspection errors were decreased by virtually monitoring the video of faulty facilities. Also those facilities were identified through the impact sound analysis and tests at the main catenary section.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.30 no.4 s.247
• /
• pp.306-313
• /
• 2006

Automated material handling system is being used as a method to reduce manufacturing cost in the semiconductor and flat panel displays (FPDs) manufacturing process. Those are considering switch-over from the traditional cassette system to single-substrate transfer system to reduce raw materials of stocks in the processing line. In the present study, the wafer transportation speed has been evaluated by numerical and experimental method for three propulsion nozzle array (face, front, rear) in an air levitation system. Test facility for 300 mm wafer was equipped with two control tracks and a transfer track of 1,500mm length. The diameter of propulsion nozzle is 0.8mm and air velocity of wafer propulsion is $50\sim150m/s$. We found that the experimental results of the wafer transportation speed were well agreed with the numerical ones. Namely, the predicted values of the maximum wafer transportation speed are higher than those values of experimental data by 16% and the numerical result of the mean wafer transportation speed is higher than the experimental result within 20%.

• Journal of Nuclear Fuel Cycle and Waste Technology
• /
• v.1 no.1
• /
• pp.29-35
• /
• 2013

The United States Department of Energy (US DOE) is conducting research and development (R&D) activities under the Used Fuel Disposition Campaign (UFDC) to support storage, transportation, and disposal of used nuclear fuel (UNF) and wastes generated by existing and future nuclear fuel cycles. R&D activities are ongoing at nine national laboratories, and are divided into storage, transportation and disposal. Storage R&D focuses on closing technical gaps related to extended storage of UNF. Transportation R&D focuses on ensuring transportability of UNF following extended storage, and addressing data gaps regarding nuclear fuel integrity, retrievability, and demonstration of subcriticality. Disposal R&D focuses on identifying geologic disposal options and addressing technical challenges for generic disposal concepts in mined repositories in salt, clay/shale, and granitic rocks, and deep borehole disposal. UFDC R&D goals include increasing confidence in the robustness of generic disposal concepts, reducing generic sources of uncertainty that may impact the viability of disposal concepts, and developing science and engineering tools to support the selection, characterization, and licensing of a repository. The US DOE has also initiated activities in the Nuclear Fuel Storage and Transportation (NFST) Planning Project to facilitate the development of an interim storage facility and to support transportation infrastructure in the near term.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.5
• /
• pp.2724-2731
• /
• 2014

As the future national defense plan of government focus on advanced weapon system, military maintenance facility becomes more important. However, military maintenance facility has been managed by director's experience and simple mathematical calculation until now. Thus, the optimization for the management of military maintenance facility is suggested by more scientistic and logical methods in this study. The study follows the procedure below. First, simulation is designed according to the analysis of military maintenance facility. Second, independent variable and dependent variable are defined for optimization. Independent Variable includes the number of maintenance machine, transportation machine, worker in the details of military maintenance facility operation, and dependent variable involves total maintenance time affected by independent variable. Third, warmup analysis is performed to get warmup period, based on the simulation model. Fourth, the optimal combination is computed with evolution strategy, meta-heuristic, to enhance military maintenance management. By the optimal combination, the management of military maintenance facility can gain the biggest effect against the limited cost. In the future, the multipurpose study, to analyze the military maintenance facility covering various weapon system equipments, will be performed.