• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.416-418
• /
• 2008

Dye-sensitized solar cell using transparent conducting oxide as electrode has large resistance such as surface resistance, charge transportation impedance in counter electrode and electrolyte, impedance between each interface. Among that resistances, surface resistance of transparent conducting oxide is relatively large. So the change of transparency has a large effect on internal resistance of dye-sensitized solar cell. Consequently, that change cause to increase or decrease the conversion efficiency. We tried to reduce the surface resistance by laser-scribing. The active area is seperated from total transparent conducting oxide by Nd:YAG laser-scribing. As a result, we achieved the improvement of efficiency about 7% and 11% in case of $0.25cm^2$ and $1.00cm^2$ dye-sensitized solar cells.

• Current Photovoltaic Research
• /
• v.5 no.4
• /
• pp.135-139
• /
• 2017

We fabricated two different transparent conducting oxide thin films of ZnO doped with Ga ($Ga_2O_3$ 0.9 wt%) as well as Al ($Al_2O_3$ 2.1 wt%) (GAZO) and ZnO doped only with Al ($Al_2O_3$ 3 wt%) (AZO). It was investigated how it affects the moisture resistance of the transparent electrode. In addition, $Cu(In,Ga)Se_2$ thin film solar cells with two transparent oxides as front electrodes were fabricated, and the correlation between humidity resistance of transparent electrodes and device performance of solar cells was examined. When both transparent electrodes were exposed to high temperature distilled water, they showed a rapid increase in sheet resistance and a decrease in the fill factor of the solar cell. However, AZO showed a drastic decrease in efficiency at the beginning of exposure, while GAZO showed that the deterioration of efficiency occurred over a long period of time and that the long term moisture resistance of GAZO was better.

• Journal of Information Display
• /
• v.5 no.3
• /
• pp.18-24
• /
• 2004

Voltage-dependent transmittance characteristics associated with various cell parameters have been studied in-plane switching liquid crystal display when both common and pixel electrodes are transparent. When both electrodes are opaque, the transmittance is related to only the distance (I) between electrodes. However, where transparent electrode is used, it is influenced not only the 1but also an electrode width (w) and rubbing angle. In addition, these factors are related to operating voltage which shows maximal transmittance. To maximize the light efficiency of the cell and obtain low operating voltage, the above-mentioned cell parameters need to be optimized.

• Current Photovoltaic Research
• /
• v.6 no.3
• /
• pp.74-80
• /
• 2018

Recently, perovskite solar cells have shown tremendous improvement in power conversion efficiencies. Moreover, they have potential in semitransparent solar cell applications due to their high absorption coefficients. In order to fabricate semitransparent perovskite solar cells with good performance, it is essential to consider the suitability of transparent electrode materials in various aspects, such as transparency, conductivity and fabrication process. In this review, candidate materials for transparent electrodes in perovskite solar cells including carbon-based nanomaterials, conductive polymers and metallic nanostructures are discussed.

• Korean Journal of Microbiology
• /
• v.10 no.1
• /
• pp.29-34
• /
• 1972

The present study is of ultra-fine structure of Cryptococcus neoformans by means of electron microscopy and reveals the following : 1) In constrast to the bacteria, the normal Cryptococcus neofrmans contains nuclear enveloped with nuclear menbrane, mitochondria, endoplasmic reticulum, distinct cell wall and cell membrane, vacuoles and storage granules as observed in the eucaryotic cells. 2) In apparent cell walls and cell membrane with the appearance of electron transparent area (ETA) and changes of cell morphology were observed in the ultra-violet ray irradiated cell. 2) In apparent cell walls and cell membrance with the appreance of electron transparent area (ETA) and changes of cell morphology were observed in the ultra-violet ray irradiated cell. 3) Morphology changes and cytoplasmic element abnormality was increased with irradiated time. 4) Increase of electron transparent area was thought to be associated with degradation of cell.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.510-514
• /
• 1997

The thin film that is electrically conductive and optically transparent is called conductive transparent thin film. ITO(Indium-Tin Oxide) which is a kind of conductive transparent thin film has been widely used in solar cell, transparent electrical heater, selective optical filter, FDP(Flat Display Panel) such as LCD(Liquid Crystal Display), PDP(Plasma Display Panel) and so on. Especially in PDP, ITO films is used as a transparent electrode in order to maintain discharge and decrease consumption power through the improvement of cell structure. In this study, we prepared ITO by reactive r.f. sputtering with indium-tin(Sn 10wt%) alloy target instead of indium-tin oxide target. The ITO films deposited at low temperature 15$0^{\circ}C$ and 8% $O_2$. Partial pressure showed about 3.6 Ω/$\square$. At the end of firing, the resistance of ITO was decreased, the optical transparence was improved above 90%.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.296-296
• /
• 2016

ITO films doped with a small amount of high-permittivity materials not only retain the basic properties of ITO films but also improve some of their properties. We report the highly conductive and transparent (ITO:Zr) films with various substrate (RT to 300oC) temperatures on glass substrate for the HIT solar cell applications. We observed a decrease in sheet resistance from 36 to $11.8{\Omega}/{\Box}$ with the increasing substrate temperature from RT to 300oC, respectively. The ITO:Zr films showed also lowest resistivity of $1.38{\times}10-4{\Omega}.cm$ and high mobility of 42.37cm-3, respectively. The surface and grain boundaries are improved with the increase of substrate temperature as shown by SEM and AFM surface morphologies. The highly conductive and transparent ITO:Zr films were employed as front electrode in HIT solar cell and the best performance of device was found to be Voc = 710 mV, Jsc = 33.70 mA/cm2, FF = 0.742, ${\eta}=17.76%$ at the substrate temperature of $200^{\circ}C$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.99-99
• /
• 2014

Transparent oxide semiconductors (TOSs) are. currently attracting attention for application to transparent electrodes in optoelectronic devices and active channel layers in thin-film transistors. One of the key issues for the realization of next generation transparent electronic devices such as transparent complementary metal-oxide-semiconductor thin-film transistors (CMOS TFTs), transparent wall light, sensors, and transparent solar cell is to develop p-type TOSs. In this talks, I will introduce issues and status related to p-type TOSs such as LnCuOQ (Ln=lanthanide, Q=S, Se), $SrCu_2O_2$, $CuMO_2$ (M=Al, Ga, Cr, In), ZnO, $Cu_2O$ and SnO. The growth and properties of SnO and Cu-based oxides and their application to electronic devices will be discussed.

• Journal of Electrochemical Science and Technology
• /
• v.2 no.2
• /
• pp.68-75
• /
• 2011

In this review, we have investigated the effect of $TiO_2$-based blocking layers (t-BLs), deposited on a transparent conductive oxide (TCO)-coated glass substrate, on the photovoltaic performance of dye-sensitized solar cells (DSSCs). The t-BL was deposited using spin-coating or sputtering technique, and its thicknesses were varied to study the influence of the thin $TiO_2$ layer in between transparent conducting glass and nanocrystalline $TiO_2$ (nc-$TiO_2$). The DSSC with the t-BL showed the improved adhesion and the suppressed charge recombination at a TCO glass substrate than those without the t-BL, which led to the higher conversion efficiency.

• Proceedings of the KIEE Conference
• /
• 2005.07c
• /
• pp.1948-1950
• /
• 2005

In the recent years, much interests and attraction has been paid on the plasma display panel. To achieve high performance display panel, there has been a strong demands for studies on the transparent conducting films such as ITO and ZnO. In this study, we propose PDP cell with ZnO transparent conducting electrode. The electrical and optical characteristics of PDP cell with ZnO transparent electrode were studied and compared with that of conventional ITO electrode.