• Applied Chemistry for Engineering
• /
• v.10 no.4
• /
• pp.603-607
• /
• 1999

The polarization characteristics of poly(vinyl alcohol)-iodine complex, (PVA-KI system) prepared by the oxidation process of PVA film containing a potassium iodide (KI) were investigated. The UV-visible spectrum of the PVA-KI system polarizing film showed avsorption bands corresponding to $I^{-}$, $I{_3}{^-}$ and $I{_5}{^-}$ chromophoric species at 220 nm, 290~360 nm, respectively. The polarization efficiency and transmittance of PVA-KI system film were significantly influenced by oxidation time, stretching ratio and concentration of KI. The prepared polarizing film exhibited a high polarization efficiency(99.5%) and transmittance(45%). Especially, the heat resistance of the polarizing film was higher than that of a commercial PVA-$I_2$ polarizing film. It may be argued that the result should come from a difference in oxidation process of PVA polarizing film.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.4
• /
• pp.303-308
• /
• 2011

The Gallium-doped ZnO(GZO) film deposited at a temperature of $200^{\circ}C$ and a pressure of 10 mtorr has an optical transmittance of 89.0% and a resistivity of $2.0\;m{\Omega}{\cdot}cm$ because of its high crystallinity. Effect of $Al_2O_3$ oxide buffer layers on the optical and electrical properties of sputtered ZnO films were intensively investigated for developing the electrodes of opto-electronic devices which demanded high optical transmittance and low resistivity. The use of $Al_2O_3$ buffer layer could increase optical transmittance of GZO film to 90.7% at a wavelength of 550 nm by controlling optical spectrum. Resistivity of deposited GZO films were much dependent on the deposition condition of $O_2/(Ar+O_2)$ flow rate ratio during the buffer layer deposition. It is considered that the $Al_2O_3$ buffer layer could increase the carrier concentration of the GZO films by doping effect of diffused Al atoms through the rough interface.

• Korean Journal of Materials Research
• /
• v.17 no.10
• /
• pp.516-520
• /
• 2007

Indium tin oxide, which is used as transparent conducting layer in flexible device, is deposited on PET film by a magnetron sputtering in 300 mm wide roll-to-roll process (vacuum web coating). Sheet resistance, specific resistance and transmittance is differed by sputtering parameters such as working pressures, oxygen partial pressure, and thickness of ITO layer. ITO layer is deposited about 90 nm at roll speed of 0.24 m/min and its sputtering power is 3 kW. From the XRD spectrum deposited ITO layer is verified as amorphous. Under working pressure varied from $3{\times}10^{-4}\;Torr$ to $2{\times}10^{-3}\;Torr$, sheet resistance is lowest at the working pressure of $1{\times}10^{-3}\;Torr$ and its value is from $110\;{\Omega}/{\square}$ to $260\;{\Omega}/{\square}$ at the thickness of 90 nm. Oxygen partial pressure also varies sheet resistance and is optimized at the regime from 0.2% ($1.8{\times}10^{-6}\;Torr$) to 0.6% ($6{\times}10^{-6}\;Torr$). In this oxygen partial pressure sheet resistance is lower than $150\;{\Omega}/{\square}$. As ITO layer thickness increases, sheet resistance decreases down to $21\;{\Omega}/{\square}$ and specific resistance is about $7.5{\times}10.4{\Omega}cm$ in 340 nm thickness ITO layer. Transmittance is measured at the wavelength of 550 nm and is about 90% for 180 nm thickness ITO/PET.

• Journal of the Korean Solar Energy Society
• /
• v.22 no.4
• /
• pp.44-50
• /
• 2002

Photosynthesis of plants is effective in the range of 550 to 700 nm of the wavelength of solar irradiation. If the conversion of ultraviolet to the above mentioned region is possible, the photosynthesizing ability is expected to be enhanced. $Eu^{3+}$ doped soda-lime bulk and $TiO_2-SiO_2$ sol-gel coated glasses were prepared and their spectroscopic properties were studied. The absorption and emission spectra for the specimens were measured with the changes of wavelength and Eu ion concentration in the range of the wavelength of 300 to 700nm. The transmittance intensity of visible light through the bulk glass and the coated one was unchanged with the addition of Eu element. The emission spectrum intensity of $Eu^{3+}$ was found to be the maximum at 618 nm which is a transition of $^5DO{\rightarrow}^7F_2$. Additionally, it was shown that the intensity was linearly increased up to 10% of the Eu concentration.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.438-440
• /
• 2005

At present, characteristic of high color reproduction for LCD TV is needed in Display market according to start mass production of LCD TV. Therefore development target for LCD is focused on improvement of color reproduction. The improving methods of high color reproduction are alteration of color Filter or Red, Green, Blue phosphor alteration of CCFL. But decrease of luminance and panel transmittance is caused by alteration of Color Filter. Accordingly, we completed LCD with high color reproduction by the most suitable emission spectrum of CCFL phosphor at panel with conventional color filter. In this experiment, we knew that LCD applied to CCFL with high color rendering characteristic had color reproduction range of 81% compared with NTSC in CIE color coordinate. According to increase of intensity peak and alteration of Red, Green, Blue phosphor spectrum, we made LCD with high color reproduction characteristic. In conclusion we achieved improvement of color reproduction ratio by alteration of CCFL phosphor without changing color filter.

• Composites Research
• /
• v.24 no.1
• /
• pp.45-50
• /
• 2011

Transparent and conductive carbon nanotube on polyethylene terephthalate (PET) were prepared by dip-coating method for self-sensing multi-functional nanocomposites. The changes in the electrical and optical properties of CNT coating mainly depended on the number of dip-coating, concentration of CNT solution. Consequently, the surface resistance and transmittance of CNT coating were sensitively controlled by the processing parameters. Surface resistance of CNT coating was measured using four-point method, and surface resistance of coated CNT could be better calculated by using the dual configuration method. Optical transmittance of PET film with CNT coating was evaluated using UV spectrum. Surface properties of coated CNT investigated by wettability test via static and dynamic contact angle measurement were consistent with each other. As dip-coating number increased, surface resistance of coated CNT decreased seriously, whereas the transmittance exhibited little lower due to the thicker CNT networks layer. Interfacial microfailure properties were investigated for CNT and indium tin oxide (ITO) coatings on PET substrates by electrical resistance measurement under cyclic loading fatigue test. CNT with high aspect ratio exhibited no change in surface resistance up to 2000 cyclic loading, whereas ITO with brittle nature showed a linear increase of surface resistance up to 1000 cyclic loading and then exhibited the level-off due to reduced electrical contact points based on occurrence of many micro-cracks.

• Korean Journal of Optics and Photonics
• /
• v.32 no.5
• /
• pp.220-229
• /
• 2021

The optical characteristics of high-power direct-lit white light-emitting diode (LED) lighting were investigated, where a quantum dot (QD) film was adopted to enhance the color-rendering index (CRI). The transmittance of the diffuser plate and the concentration of the QD film were varied in this study. The color coordinates and the correlated color temperature (CCT) did not show any appreciable change, while the CRI values increased slightly as the transmittance of the diffuser plate decreased. The investigated optical properties were nearly independent of the viewing angle, and the luminance distribution was close to Lambertian. The CCT decreased from approximately 6000 K to approximately 4000 K as the concentration of the QD film increased from 0 to 7.5 wt%, which was due to the enhanced red component in the emission spectrum. The CRI increased to approximately 95 for some optical configurations of the lighting. These results demonstrate that glare-free, color-changeable, high-rendering LED lighting can be realized by using a combination of a diffuser plate of appropriate transmittance and a red QD film.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.63-66
• /
• 2004

Transparent MgO thin films were deposited on glass substrates by electron beam evaporation of MgO (99.99%) under $O_2$ atmosphere at 150-250 $^{\circ}C$. These films were characterized for their useful properties such as thickness, transmission, and refractive index using ultraviolet / visible (UV/VIS) spectrophotometer, scanning electron microscopy (SEM), and Spectroscopic Ellipsometry. The thickness of MgO films were measured by alpha step instrument and found to be 600 nm to 1000 nm and are meeting the stoichiometry. The transmission spectrum of these films shows transmittance values ${\sim}$92%..

• Current Photovoltaic Research
• /
• v.8 no.1
• /
• pp.1-5
• /
• 2020

The most important factor in enhancing the performance of an optical device is to minimize reflection and increasing transmittance of light for a broad wavelength range. The choice of appropriate coating material is crucial in decreasing reflection losses at the substrate. The purpose of this review is to highlight anti-reflection coating (ARC) materials that can be applied to silicon solar cell and glass substrate for minimizing reflection losses. The optical and electrical behavior of ARC on a substrate is highly dependent on thickness and refractive index (RI) of ARC films that are being deposited on it. The coating techniques and performance of single and multi-layered ARC films after coated on a substrate in a wide range of wavelength spectrum will be studied in the paper.

• Proceedings of the Optical Society of Korea Conference
• /
• 2007.02a
• /
• pp.221-222
• /
• 2007

The UV laser trimming can be useful to have an accurate performance specification of the passive waveguide devices. In order to measure the change of the refractive index of polymer overclad layer under the irradiation of uv light in a high precision Bragg grating is fabricated on the silica core of planar waveguide and the corresponding transmittance spectrum was analyzed. An effective refractive index change of $4.7x10^{-5}$ was obtained for a straight waveguide when its $60{\mu}m$-thick overclad was irradiated by UV laser pulses of its total fluence 24 $J/cm^2$.