• Proceedings of the KSR Conference
• /
• 2005.05a
• /
• pp.776-781
• /
• 2005

In this paper, using received channel information, we analyze performance in MIMO multiuser system in low-to-medium mobile speed by selecting each user's constellations, powers, and transmit antennas. Given a target of symbol error, we determine each user's constellations, powers, selected tranprobability smit antennas such that the required signal-to-noise(SNR) is minimized for MMSE, V-BLAST receiver according to each user's information and channel estimation information. When we do power control with antenna selection technique through uplink channels of MIMO system in low-to-medium mobile speed, we analyze system performance with wireless channel information from Base-Station(BS) to Users. By simulation, it has been shown that the proposed antenna selection scheme for transmitting data offer better performance improvement than all transmit antennas for transmitting data.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.40 no.7
• /
• pp.273-281
• /
• 2003

This paper proposes a new time synchronization scheme for the Automatic Identification System(AIS). The proposed scheme utilizes a Temperature Compensated Crystal Oscillator(TCXO) as a local reference clock, and consists of a Digitally Controlled Oscillator(DCO), a divider, a phase comparator, and register blocks. Primary time reference is IPPS from GPS receiver that is synchronized to Universal Time Coordinated(UTC). And if GPS is unavailable, other station's signal is utilized as secondary time reference. The phase comparator measures time difference between the 1PPS and the generated transmit clock. The measured time difference is compensated by controlling the DCO and the transmit clock is synchronized to the Universal Time Coordinated(UTC). The synchronized transmit clock(9600Hz) is divided into the transmitting time slot(37.5Hz). The proposed scheme is tested in an experimental AIS transponder set. The experimental result shows that the proposed module satisfies the timing specification of the AIS technical standard, ITU-R M.1371-1.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.5
• /
• pp.47-54
• /
• 2016

In the underwater environment, high resolution can be achieved in the range direction by transmitting and receiving a signal of a particular band and/or waveform. The design of a transmit signal used in the active sonar is very important in order to detect a cylindrical object within a short distance less than 1 km, which is the detection distance of this paper. Designing a transmit signal optimal to a sonar requires appropriate selection of its center frequency and bandwidth, which allows the maximum detection distance of a sonar. In this paper, in terms of maximizing echo excess and signal to noise ratio (SNR), optimum frequency analysis is carried out under various conditions of diverse parameters. In addition, the investigation focused on the determinating a bandwidth is also performed for the purpose of satisfying the performance requirement of range resolution and azimuth resolution.

• Journal of Communications and Networks
• /
• v.7 no.2
• /
• pp.157-170
• /
• 2005

The combination of multiple antennas and multi-carrier code division multiple-access (MC-CDMA) is a strong candidate for the downlink of the next generation mobile communications. The study of such systems in scenarios that model real-life trans-missions is an additional step towards an optimized achievement. We consider a realistic MIMO channel with two or four transmit antennas and up to two receive antennas, and channel state information (CSI) mismatches. Depending on the mobile terminal (MT) class, its number of antennas or complexity allowed, different data-rates are proposed with turbo-coding and asymptotic spectral efficiencies from 1 to 4.5 bit/s/Hz, using three algorithms developed within the European IST-MATRICE project. These algorithms can be classified according to the degree of CSI at base-station (BS): i) Transmit space-frequency prefiltering based on constrained zero-forcing algorithm with complete CSI at BS; ii) transmit beamforming based on spatial correlation matrix estimation from partial CSI at BS; iii) orthogonal space-time block coding based on Alamouti scheme without CSI at BS. All presented schemes require a reasonable complexity at MT, and are compatible with a single-antenna receiver. A choice between these algorithms is proposed in order to significantly improve the performance of MC-CDMA and to cover the different environments considered for the next generation cellular systems. For beyond-3G, we propose prefiltering for indoor and pedestrian microcell environments, beamforming for suburban macrocells including high-speed train, and space-time coding for urban conditions with moderate to high speeds.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.11B
• /
• pp.1151-1168
• /
• 2009

Improving packet loss does not necessarily coincide with the improvement in user perceivable QoS because each frame carries different degree of importance. We propose Significance-aware packet scheduling (SAPS) to maximize user perceivable QoS. SAPS carries out two fundamental issues of packet scheduling: "What to transmit" and "When to transmit?" To adapt to the available bandwidth, it is necessarily to transmit the subset of the data packets if the entire set of packets can not be transmitted. "Packet Significance" quantifies the importance of the frame by elaborately incorporating frames' dependency. Greedy approach is used in selecting packets and transmission schedule is determined based on the Packet Significance. The proposed scheme is tested using publicly available MPEG-4 video clips. Decoding engine is embedded in the simulation software and user perceivable QoS is exposeed in termstermiSNR. Throughout the simulation based experiment, the performance of the proposed scheme is compared two other schemes: Size-based packet scheduling and Bit-rate based best effort packet scheduling. SAPS successfully incorporates the semantics of a packet and improves user perceivable QoS significantly. It successfully provides unequal protection to more important packets.

• Journal of Biomedical Engineering Research
• /
• v.23 no.6
• /
• pp.419-430
• /
• 2002

In this paper. we propose an efficient method for implementing hi-directional pixel-based focusing(BiPBF) based on a sparse array imaging technique. The proposed method can improve spatial resolution and frame rate of ultrasound imaging with reduced hardware complexity by synthesizing transmit apertures with a small number of sparsely distributed subapertures. As the distance between adjacent subapertures increases, however. the image resolution tends to decrease due to the elevation of grating lobes. Such grating lobes can be eliminated in conventional synthetic aperture imaging techniques. On the contrary, grating lobes arisen from employing sparse synthetic transmit apertures can not be eliminated, which has been shown analytically in this paper. We also propose the condition and method for suppressing the grating lobes below -40dB, which is generally required in practical imaging. by placing the transmit focal depth at a near depth and properly selecting the subaperture distance in Proportion to receive aperture size. The results of both the Phantom and in vivo experiments show that the proposed method implements two-wav dynamic focusing using a smaller number of subapertures, resulting in reduced system complexity and increased frame rate.

• Journal of Biomedical Engineering Research
• /
• v.31 no.4
• /
• pp.269-274
• /
• 2010

The purpose of this study was to develop the FSR sensor suit that controls walking assist device for paraplegic patients. The FSR sensor suit was to detect user's intent and patterns for walking by measuring pressure on the palm and the sole of user's foot. It consisted of four modules: sensing pressure from palm, changing modes and detecting pressure on the palm/at the wrist, sensing pressure from the soles of user's foot, and host module that transmit FSR data obtained from sensing modules to PC. Sensing modules were connected to sensing pads which detect analog signals obtained from the palm or the sole of foot. These collect signals from the target regions, convert analog signals into digital signals, and transmit the final signals to host module via zigbee modules. Finally, host modules transmit the signals to host PC via zigbee modules. The study findings showed that forces measured at the palm when using a stick reflected user's intent to walk and forces at the sole of the user's foot revealed signals detecting walking state.

• Journal of Satellite, Information and Communications
• /
• v.11 no.2
• /
• pp.55-59
• /
• 2016

Conventional RF energy harvesting systems can harvest energy and decode information from same source as an Hybirid-AP (H-AP). However, harvesting efficiency is seriously dependent on distance between users and H-AP. Therefore, in this paper, we proposed a transmission model for RF harvesting consisting of information and power source separately called Decoupled RF Energy harvesting networks. Main purpose of this paper is to maximize energy efficiency under various constraints of transmit power from H-AP and power beacon (PB), minimum quality of service and quality of harvested power of each users. To measure proposed model's performance, we proposed optimal time scheduling algorithms for energy efficiency (EE) maximization using Lagrangian dual decomposition theory that locally maximizes the EE by obtaining suboptimal values of three arguments : transmit power of H-AP, transmit power of PB, frame splitting factor. Experiment results show that the proposed energy-efficient algorithms converge within a few iterations with its optimality and greatly improve the EE compared to that of baseline schemes.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.2A
• /
• pp.202-213
• /
• 2004

In this paper, we propose a preamble structure and synchronization/channel estimation methods for OFDM-based multiple antenna WLAN systems that have 200Mbps transmit rate. With the proposed preamble structure, multiple antenna WLAN systems are backward-compatible with IEEE 802.11a systems which use the same 5㎓ band and synchronization performance is better than that of single antenna OFDM systems. For channel estimation, the preamble overhead is small and performance degradation by timing synchronization error that causes the critical problem of conventional comb-type multiple antenna channel estimation method also can be minimized by frequency domain phase recovery. Synchronizer and channel estimator for proposed preamble structure are implemented and verified using Verilog HDL. For the system with 4 transmit antennas and 4 receive antennas, about 150K gates are needed for synchronizer and 12K gates for channel estimator.

• Design & Manufacturing
• /
• v.10 no.1
• /
• pp.19-25
• /
• 2016

Connectors are very important components that transmit electric signals to different parts. It must maintain intensity of the connector to prevent defects from impact and maintain contact to transmit electric signals. Most of the external parts of the connector, which act as the main framework, are formed by injection molding. However, bend deformation occurs for injection molded products due to the residual stress left inside the product after product molding. When the bend deformation is large, it does not come into complete contact when being assembled with other parts, which leads to connector contact intensity not being properly maintained. In result, the main role of the connector, which is to transmit electric signals, cannot be performed. In order to address this problem, this study conducted bend deformation cause analysis through bend deformation analysis to predict and prevent bend deformation of housings and wafers, which are injection molded products of pressure welded connectors that are normally applied in compact mobile and display products. Bend deformation analysis was carried out by checking the charging time, pressure distribution and temperature distribution through wire to board connector wafer and housing injection molding analysis. Based on the results of the bend deformation analysis results, the cause of the bend deformation was analyzed through deformation resulting from disproportional cooling, deformation resulting from disproportional contraction, and deformation resulting from ingredient orientation. In result, it was judged that the effects for bend deformation were biggest due to disproportional contraction for both the pressure welded connector wafer and housing.