• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.44 no.8
• /
• pp.42-50
• /
• 2007

This paper presents design methods for dual-frequency(2.4/5.8GHz) active receiving antennas. The proposed active receiving antennas are designed to interconnect the output port of a wideband antenna to the input port of an active device of High Electron Mobility Transistor directly and to receive RF signals of 2.4GHz and 5.2GHz simultaneously where the impedance matching conditions are optimized by adjusting the length of $1/20{\lambda}_0$(@5.8GHz) CPW transmission line in the planar antenna The bandwidth of implemented dual-frequency active receiving antennas is measured in the range of 2.0GHz to 3.1GHz and 5.25GHz to 5.9GHz. Gains are measured of 17.0dB at 2.4GHz and 15.0dB at 5.2GHz. The measured noise figure is 1.5dB at operating frequencies.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.46 no.5
• /
• pp.56-63
• /
• 2009

The IEEE 802.11 standard has been used for wireless data networks such as wireless LAN, ad-hoc network, and vehicular ad-hoc network. Thus, the performance analysis of the IEEE 802.11 specification has been one of the hottest issues for network optimization and resource management. Most of the analysis studies were performed in a data plane of the IEEE 802.11 unicast. However, IEEE 802.11 broadcast is widely used for topology management, path management, and data dissemination. Thus, it is important to understand the performance of the broadcast scheme for the design of efficient wireless data network. In this contort, we analyze the IEEE 802.11 broadcast scheme in terms of the broadcast frame reception probability according to the distance from a sending node. Unlike the other works, our analysis framework includes not only the system parameters of the IEEE 802.11 specification such as transmission range, data rate, minimum contention window but also the networking environments such as the number of nodes, network load, and the radio propagation environments. Therefore, our analysis framework is expected to be used for the development of protocols and algorithms in a dynamic wireless data network.

• Journal of the Korean Magnetics Society
• /
• v.12 no.4
• /
• pp.127-131
• /
• 2002

We fabricated MTJ devices that have doubly oxidized tunnel barrier using plasma oxidation method to from oxidized AlO$\sub$x/ tunnel barrier. Doubly oxidation I, which sputtered 10 ${\AA}$-bottom Al layer and oxidized it with oxidation time of 10 s. Subsequent sputtering of 13 ${\AA}$-Al was performed and the metallic layer was oxidized for 50, 80 and 120 s., respectively. Doubly oxidation II, which sputtered 10 ${\AA}$-bottom Al layer and oxidized it varying oxidation time for 30∼120 s. Subsequent sputtering of 13 ${\AA}$-Al was performed and the metallic layer was oxidized for 210 sec. Double oxidation process specimen showed MR ratio of above 27％ in all experiment range. Singly oxidation process. 13 ${\AA}$-Al layer and oxidized up to 210 s, showed less MR ratio and more narrow process window than those of doubly oxidation. Cross-sectional TEM images would that doubly oxidized barrowers were thinner and denser than singly oxidized ones. XPS characterization confirmed that doubly oxidation of Fe with bottom insulating layer. As a result, doubly oxidation could have superior MR ratio in process extent during long oxidation time because of preventing oxidation of bottom magnetic layer than singly oxidation.

• Korean Journal Plant Pathology
• /
• v.3 no.3
• /
• pp.223-235
• /
• 1987

Samples showing yellow mosaic symptom of Lilium spp. with necrotic fleck, stunting, malformation, and colour breaking were collected from lily-growing areas in the southern part of Korea. Two viruses were distinguished under a electron microscope and their host range, serological reaction, stability in sap, type of aphid transmission, and relations with cells and tissues were examined. Broad bean wilt virus (BBWV) was transmitted by sap-inoculation to 23 plant species in 8 families and by the aphid, Myzus persicae. This virus was inactivated after 10 min at 70C, at dilution of $10^{-3}$, and after 6 days at about 20C. Electron microscopic examination of purified preparation showed that the virus is spherical particle of 28nm in diameter. The virus reacted positively with BBWV-antiserum in agar gel diffusion test. In ultrathin sections of BBWV infected tissues, large aggregates or crystalline array of virus particles and vesicular body were found in the cytoplasm, vacuole, and nucleus of mesophyll cells. Cucumber mosaic virus (CMV) was transmitted by sap-inoculation. Electron microscopic examination of its purified preparation showed spherical particles of 30nm in diameter. The virus reacted positively with CMV-Y strain-antiserum in agar gel diffusion test. In ultrathin sections of CMV infected tissues, crystalline array of virus particles were found in the vacuole and a large number 0f virus particles were found in the cytoplasm and the plasmodesmata of mesophyll cells. When each of these viruses was retransmitted to Lilium tigrinum. L. concolor, and L. auratum, BBWV induced slight symtoms and colour breaking, but CMV induced yellowing mosaic or necrotic fleck.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.41 no.8
• /
• pp.105-111
• /
• 2004

In this paper, millimeter-wave high gain and broadband MHEMT cascode amplifiers were designed and fabricated. The 0.1 ${\mu}{\textrm}{m}$ InGaAs/InAlAs/GaAs Metamorphic HEMT was fabricated for cascode amplifiers. The DC characteristics of MHEMT are 640 mA/mm of drain current density, 653 mS/mm of maximum transconductance. The current gain cut-off frequency(f$_{T}$) is 173 GHz and the maximum oscillation frequency(f$_{max}$) is 271 GHz. By using the CPW transmission line, the cascode amplifier was designed the matched circuit for getting the broadband characteristics. The designed amplifier was fabricated by the MHEMT MIMIC process that was developed through this research. As the results of measurement, the 1 stage amplifier obtained 3 dB bandwidth of 37 GHz between 31.3 to 68.3 GHz. Also, this amplifier represents the S21 gain with the average 9.7 dB gain in bandwidth and the maximum gain of 11.3 dB at 40 GHz. The 2 stage amplifier has the broadband characteristics with 3 dB bandwidth of 29.5 GHz in the frequency range from 32.5 to 62.0 GHz. The 2 stage cascode amplifier represents the high gain characteristics with the average gain of 20.4 dB in bandwidth and the maximum gain of 22.3 dB at 36.5 GHz.z.z.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.44 no.1
• /
• pp.26-39
• /
• 2007

In recent years, rate control is an important technique in real time video communication applications using H.264/AVC. Many existing rate control algorithms employ the quadratic rate-distortion model, which is determine the target bits for each P frame. In this paper, a new rate control algorithm for transmission of H.264/AVC video bit stream through CBR(Constant Bit Rate) channel is proposed. The proposed algorithm predicts an adaptive QP(Quantization Parameter) for improving video distortion, due to high motion and abruptly scene change, which target bit rate and MAD(Mean of Absolute Difference) for current frame considering image complexity variance between previous and current frames. Additionally, it uses frame skip technique to maintain bit stream within a manageable range and protect buffer from overflow or underflow. Experimental results show that the proposed method gives a quality improvement of about 0.5dB when compared to previous rate control algorithm. Also our proposed algorithm encodes the video sequences with less frame skipping compared to the existing rate control for H.264/AVC.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.9
• /
• pp.68-73
• /
• 2013

In this paper, we proposed a readout circuit of pulse waveform and rate for a U-health system to monitor health condition. For long-time operation without replacing or charging a battery, either pulse waveform or pulse rate is selected as the output data of the proposed readout circuit according to health condition of a user. The proposed readout circuit consists of a simple digital logic discriminator and a dual-mode ADC which operates in the ADC mode or in the count mode. Firstly, the readout circuit counts pulse rate for 4 seconds in the count mode using the dual-mode ADC. Health condition is examined after the counted pulse rate is accumulated for 1 minute in the discriminator. If the pulse rate is out of the preset normal range, the dual-mode ADC operates in the ADC mode where pulse waveform is converted into 10-bit digital data with the sampling frequency of 1 kHz. These data are stored in a buffer and transmitted by 620 kbps to an external monitor through a RF transmitter. The data transmission period of the RF transmitter depends on the operation mode. It is generally 1 minute in the normal situation or 1 ms in the emergency situation. The proposed readout circuit was designed with $0.11{\mu}m$ process technology. The chip area is $460{\times}800{\mu}m^2$. According to measurement, the power consumption is $161.8{\mu}W$ in the count mode and $507.3{\mu}W$ in the ADC mode with the operating voltage of 1 V.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.10
• /
• pp.541-546
• /
• 2020

The surveillance radar for naval ships is an essential equipment of a battle system that executes the detection and tracking of targets, and the shooting support function; it calculates the three-dimensional track of the target range, azimuth, and altitude to carry out its duty. The surveillance radar consists of an antenna, a transceiver, a processing unit, and an air dryer section. The radar radiates the transmission signal on the antenna section, receives the reflected signal from the target, and amplifies the signals on the transceiver section. The signal received from the antenna is used to provide the operator with target information in various ways. This study identified the display problems when the information about the target is displayed through the radar. The causes of the problems were analyzed and improved. The tracking disappearance phenomenon caused by the altered-course of the ship was improved on the TWS tracking algorithm. The validity of the improved TWS tracking algorithm was confirmed by the normal condition of the target status on the B-scope.

• Journal of Advanced Navigation Technology
• /
• v.13 no.6
• /
• pp.916-925
• /
• 2009

4S (Ship to Ship, Ship to Shore) communication is the key to strategic development of e-navigation, a core element of IT vessel convergence. 4S communication is intended to integrate and standardize various communication infrastructures on land and communication equipment complying with communication equipment equipped in ships. This paper aims to apply the Korean technology IEEE 802.16e adopted as an international standard, to replace and compensate for existing vessel communication media such as low speed HF/MF/VHF to the ocean environment. To this end, various experimental conditions between the coast station where a relay station was installed and related equipment equipped on a ship are set. Communication signals were monitored and the RSSI and CINR were measured. Based on experimental analysis and results, various challenges and solutions which may occur in ocean environment were sought, and communication availability was analyzed through transmission data throughput, at the maximum effective distance range of the signal. It was proven that high speed multimedia data could be exchanged for up to 20 km even among 80km kph ships moving around near the sea, ensuring that this technology could be applied to the ocean environment.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.463-463
• /
• 2014

Dye-sensitized solar cells (DSSCs) have generated a strong interest in the development of solid-state devices owing to their low cost and simple preparation procedures. Effort has been devoted to the study of electrolytes that allow light-to-electrical power conversion for DSSC applications. Several attempts have been made to substitute the liquid electrolyte in the original solar cells by using (2,2',7,7'-tetrakis (N,N-di-p-methoxyphenylamine)-9-9'-spirobi-fluorene (spiro-OMeTAD) that act as hole conductor [1]. Although efficiencies above 3% have been reached by several groups, here the major challenging is limited photoelectrode thickness ($2{\mu}m$), which is very low due to electron diffusion length (Ln) for spiro-OMeTAD ($4.4{\mu}m$) [2]. In principle, the $TiO_2$ layer can be thicker than had been thought previously. This has important implications for the design of high-efficiency solid-state DSSCs. In the present study, we have fabricated 3-D Transparent Conducting Oxide (TCO) by growing tin-doped indium oxide (ITO) nanowire (NWs) arrays via a vapor transport method [3] and mesoporous $TiO_2$ nanoparticle (NP)-based photoelectrodes were prepared using doctor blade method. Finally optimized light-harvesting solid-state DSSCs is made using 3-D TCO where electron life time is controlled the recombination rate through fast charge collection and also ITO NWs length can be controlled in the range of over $2{\mu}m$ and has been characterized using field emission scanning electron microscopy (FE-SEM). Structural analyses by high-resolution transmission electron microscopy (HRTEM) and X-Ray diffraction (XRD) results reveal that the ITO NWs formed single crystal oriented [100] direction. Also to compare the charge collection properties of conventional NPs based solid-state DSSCs with ITO NWs based solid-state DSSCs, we have studied intensity modulated photovoltage spectroscopy (IMVS), intensity modulated photocurrent spectroscopy (IMPS) and transient open circuit voltages. As a result, above $4{\mu}m$ thick ITO NWs based photoelectrodes with Z907 dye shown the best performing device, exhibiting a short-circuit current density of 7.21 mA cm-2 under simulated solar emission of 100 mW cm-2 associated with an overall power conversion efficiency of 2.80 %. Finally, we achieved the efficiency of 7.5% by applying a CH3NH3PbI3 perovskite sensitizer.