• Journal of Powder Materials
• /
• v.22 no.5
• /
• pp.350-355
• /
• 2015

Perforated polygonal cobalt oxide ($Co_3O_4$) is synthesized using electrospinning and a hydrothermal method followed by the removal of a carbon nanofiber (CNF) template. To investigate their formation mechanism, thermogravimetric analysis, field-emission scanning electron microscopy, transmission electron microscopy, X-ray diffraction, and X-ray photoelectron spectroscopy are examined. To obtain the optimum condition of perforated polygonal $Co_3O_4$, we prepare three different weight ratios of the Co precursor and the CNF template: sample A (Co precursor:CNF template- 10:1), sample B (Co precursor:CNF template-3.2:1), and sample C (Co precursor:CNF template-2:1). Among them, sample A exhibits the perforated polygonal $Co_3O_4$ with a thin carbon layer (5.7-6.2 nm) owing to the removal of CNF template. However, sample B and sample C synthesized perforated round $Co_3O_4$ and destroyed $Co_3O_4$ powders, respectively, due to a decreased amount of Co precursor. The increased amount of the CNF template prevents the formation of polygonal $Co_3O_4$. For sample A, the optimized weight ratio of the Co precursor and CNF template may be related to the successful formation of perforated polygonal $Co_3O_4$. Thus, perforated polygonal $Co_3O_4$ can be applied to electrode materials of energy storage devices such as lithium ion batteries, supercapacitors, and fuel cells.

• Korean Journal of Materials Research
• /
• v.30 no.6
• /
• pp.279-284
• /
• 2020

In this work, a carbon-doped carbon nitride photocatalyst is successfully synthesized through a simple centrifugal spinning method after heat treatment. The morphology and properties of the prepared photo catalyst are characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), UV-vis spectrophotometer (UV-vis), and specific surface area. The results show that the band gap of the prepared sample, g-CN-10 is 2.1 eV, is significantly lower than that of pure carbon nitride, 2.7 eV. As the amount of cotton candy increased, the absorption capacity of the prepared catalyst for visible light is significantly enhanced. In addition, the degradation efficiency of Rhodamine B (RhB) by sample g-CN-10 is 98.8 % over 2 h, which is twice that value of pure carbon nitride. The enhancement of photocatalytic ability is attributed to the increase of specific surface area after the carbon doping modifies carbon nitride. A possible photocatalytic degradation mechanism of carbon-doped carbon nitride is also suggested.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.23 no.4
• /
• pp.333-340
• /
• 2013

Objectives: This study was designed to establish an accurate analytical method for asbestos in a biological sample for determining occupational asbestos-related diseases and relief of the health effects of environmental asbestos. Methods: Biological samples were obtained from lungs of rats following intratracheal instillation of asbestos(Chrysotile, anthophyllite) and were prepared according to digestion method(Wet digestion, high temperature ashing, low temperature ashing). The samples were then analyzed for asbestos fibers using a transmission electron microscope equipped with an energy dispersive X-ray spectrometer. Results: Low temperature plasma ashing removed more of the organic components and reduced fiber loss compared to the wet digestion method, making specimens so prepared more suitable for transmission electron microsocpy. Conclusions: The low temperature ashing technique is the most accurate method for analyzing asbestos in biological samples.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11a
• /
• pp.255-257
• /
• 2001

In this paper, the silicon rubber insulator for transmission line was experimented for 1,000 hours aging test in salt-fog condition. To evaluate and examine the aging properties of silicon rubber insulator for test, the leakage current of surface was measured. Also hydrophobicity and scanning electron microscopy were compared with initial and aged sample respectively Above results, we can confirm that the surface properties of silicon rubber insulator easily aged by salt-fog condition.

• Applied Microscopy
• /
• v.26 no.4
• /
• pp.479-487
• /
• 1996

Thin epilayer structures of GaAs/AlAs/InGaAs, grown by Molecular Beam Epitaxy, were investigated by high resolution transmission electron microscopy, Image in the [110] zone axis was taken and compared with the calculated images. The supercell structure which contains GaAs, AlAs and InGaAs layers was designed and was employed in the image calculation with MacTempas computer program. Good agreement was shown between experimental image and a set of calculated images with varying defocus and sample thickness.

• Applied Microscopy
• /
• v.27 no.1
• /
• pp.101-109
• /
• 1997

The nonstoichiometric ordering of Mg and Nb cations in undoped and La-doped lead magnesium niobate solid solutions has been investigated by means of high-resolution transmission electron microscopy and computer image simulation. High-resolution lattice images were obtained under various microscope imaging conditions and objective apertures. Computer image simulations were performed for a wide range of sample thickness, defocusing value, and long-range order parameter. The simulated images revealed that the lattice images of the ordered regions were predominantly dependent on the long-range order parameter. From the comparisons of the experimental and simulated images for the ordered regions, the long-range order parameter approximately ranged 0.2 to 0 7. It was also found that the ordered structure has a $(NH_4)_3-FeF_6$ structure, which consists of alternating Mg- and Nb-preferred sublattices along the (111) directions.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.38-42
• /
• 2002

HAZ(Heat Affected Zone of weldm ents) properties were investigated for a high nitrogen austenitic stainless steel with a chemical composition of Fe-0.02C-0.15Si-6.00Mn-10.0Ni-23.0Cr-2.00Mo-0.48N-0.14V. Thermal cycle of HAZ was simulated by the thermal cycle simulator (Gleeble 1500). The heat treatment was applied to the Charpy test size sample without notch under various peak temperatures and/or the holding times condition. V-notch Charpy test was performed at the temperature range of 273~77 K. Metallographic examination also was carried out by using optical microscopy, scanning electron microscopy and transmission electron microscopy. The simulated specimens revealed a slight embrittlement compared with the base materials. The impact toughness of the specimens deteriorated with the decreasing test temperature. The results from Charpy V-notch test, however, showed that significant degradation of absorbed energy caused by brittle fracture was not observed for the specimen tested in the test temperature range.

• Proceedings of the KIEE Conference
• /
• 1997.07d
• /
• pp.1304-1307
• /
• 1997

A hydrogen gas sensor utilizing Pt/$SnO_2$ system was fabricated by the pressed pellet method. The crystal structure, direction of the crystal, crystal size and microstructure between the catalyst and the support ($SnO_2$) were characterized with Electron Diffraction Analysis, Transmission Electron Microscopy, Scanning Electron Microscopy. After the reactor with a Pt/$SnO_2$ sample was run with a flow rate of 30sccm (a mixture of $0.5%H_2$ in $N_2$) for a while, the resistance of $SnO_2$ was saturated, but the $SnO_2$ kept absorbing $H_2$ gas. $H_2$ gas sensing properties of Pt/$SnO_2$ were investigated at several temperatures. As a result, it was observed that Pt/$SnO_2$ has high sensitivity at $300^{\circ}C$ and $400^{\circ}C$.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.7 no.2
• /
• pp.276-283
• /
• 1997

A dry impregnation method was used for preparing pellet type Pt/$SnO_2$ gas sensor. The crystal structure, direction of the crystal, crystal size and microstructure between the catalyst and the support ($SnO_2$) were characterized with electron diffraction analysis, transmission electron microscopy, scanning electron microscopy. The characterization indicates that when Pt/$SnO_2$ sample is calcined at $400^{\circ}C$, the Cl content associated with the Pt phase diminishes and the part of Pt is moved into $SnO_2$ support. This results in the enhancement of gas sensitivity. After the reactor with a Pt/$SnO_2$ sample was run with a flow rate of 30 sccm (a mixture of 0.5% $H_2$ in $_N2$) for a while, the resistance of $SnO_2$ was saturated, but the $SnO_2$ kept absorbing $H_2$ gas. This indicates that the surface state was saturated. For the 14 ppm $H_2$ gas, the sensitivity of Pt/$SnO_2$ devices was about 81% at an operating temperature of $300^{\circ}C$.

• Electrical & Electronic Materials
• /
• v.8 no.4
• /
• pp.464-471
• /
• 1995

메그네트론 스퍼터링으로 제작한 고밀도 다층박막($Co_75{{Pt_12}{Cr_13}}$합금) 디스크를 투과전자현미경을 이용해 단면 및 평면의 미세조직의 조사 혹은 미소부위 성분분석을 할 경우, 선행되어야하는 시편준비 경로와 각 단계별 구체적방법 및 그 효과를 연구하였다. Ion밀링시간이 증가함에 따라 시료가 얇게 되는과정에서 스퍼터링된 물질이 관찰될 시편부위의 다른 표면에 증착되므로써 미세조직의 선명도를 해칠 수 있고, 이로인한 해석상의 오류가능성이 시사되었다. 또한, 자기박막 디스크와 같이 다층으로 구성된 단면분석용 시료에서는 서로 맞붙인 실리콘 단결정 접착면을 따라 밀링속도가 선택적으로 커서 우선축이 생김으로써 양질의 시편을 얻기 어려운 문제점이 제기되었다. 이같은 문제를 포함한 전자현미경 시료준비과정에서 생길 수 있는 문제를 해결할 수 있는 실마리와 이를 이용해 수행한 전자현미경 분석결과 및 효과적인 시편준비방법이 본 논문에서 언급되었다.