• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.42 no.11
• /
• pp.67-78
• /
• 2005

In this paper, impedance characteristics of overhead medium-voltage (MV) power line for power line communication (PLC) is analyzed. For analysis, a two-port equivalent network model of MV power lines is derived. By applying the equivalent model and basic transmission line theory, input impedance at the signal induction part is calculated. And also calculated input impedance of power line itself that the medium voltage coupler and coaxial cable effect are removed. For verification, impedance of power lines is measured at a test field for an MV PLC. The results show that impedance of MV power line itself is between $200\;{\Omega}\;and\;300\;{\Omega}$ and converges to a half of their characteristic impedance with increasing frequency. And also measured data is very similar to calculated data.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.4
• /
• pp.1-9
• /
• 2007

Linearity is the one of the most important features for analog-optic transmission system. In our research, the available bandwidth for the feed-forward compensation circuit is enhanced by using a 180 hybrid coupler in the circuit. The bandwidth having the decreased 3rd-order intermodulation distortion(IMD3) over 10 dB is extended over 200 MHz with the center frequency of 1.6 GHz. We performed an efficient bandwith measurement for the feed-forward compensation system, which uses the network analyzer instead of the traditional measuring system that uses two RF signal generators and the spectrum analyzer. We identify the usefulness of this method from experimental results. In this study, we used cheap digital-purpose laser diodes for economical aspect, which proves the efficiency of the proposed analog system. The spurious-free dynamic range is improved about 6 dB/Hz.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.23 no.4
• /
• pp.1035-1044
• /
• 1998

A new multi-channel access scheme and the associated network architecture for a single-hop WDM local area network is proposed in this paper. The proposed architecture has Central Scheduling Node (CSN) for the transmission coordination among many users, which is one of the key issues in single-hop WDM networks. The data channels, source nodes, and destination nodes are selected at CSN in very simple menner. Our scheme can relive the control processing overhead at all nodes in the network which is caused in existing distributed scheduling algorithms. CSN is simple in the architecture can be implemented easily. in respect to the network performance, the maximum obtainable throughput is up to that of the ideal output queuing because of collision free scheduling. We use the MQMS (multi-queue multi-server) model for performance analaysis.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.12
• /
• pp.2615-2621
• /
• 2010

The multi-band six-port phase correlator using metamaterial was designed and fabricated in this paper. The lumped metamaterial structure that can process the dual-band receiving signal was analyzed. Based on the analyzed results, the small-sized metamatrial six-port phase correlator for multi-band direct conversion method was proposed and fabricated. Also, the resistive power divider and $90^{\circ}$ hybrid coupler that comprises the six-port phase correlator were implemented based on the scattering parameters of metamatrial six-port phase correlator. The measured results of the proposed six-port phase correlator show the good agreement with simulation results. The performance of the six-port phase correlator shows the reflection loss below -20 dB in the dual-band. Also, the proposed six-port phase correlator got a good transmission characteristic within 1 dB gain difference and ${\pm}4.1^{\circ}$ phase imbalance, respectively.

• Korean Journal of Optics and Photonics
• /
• v.10 no.3
• /
• pp.226-232
• /
• 1999

We have investigated the output power performance of a continuous-wave chromium-doped YAG laser ($Cr^{4+}$:YAG laser), pumped by a Nd: YAG laser. With an output coupler of 1% transmission, we obtained as much as 400 mW of the average output power at 1.450 ${\mu}{\textrm}{m}$. The power slope efficiency of 8%, when the gain medium was cooled to 2$0^{\circ}C$. We tuned the wavelength of the $Cr^{4+}$:YAG laser, at pump power of 6 W, by using birefringent filter. As a result, lasing wavelength was tuned from 1.399 ${\mu}{\textrm}{m}$ to 1.532 ${\mu}{\textrm}{m}$, with the maximum output power of 340 mW at 1.4903 ${\mu}{\textrm}{m}$ and the linewidth was 0.21 nm.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.9
• /
• pp.745-752
• /
• 2016

In the era of the Internet of Things, where all physical objects are connected to the Internet, we suggest a remote control system using a Raspberry Pi single-board computer with ZigBee, which can turn an indoor light-emitting diode (LED) and a multiple-tap on and off, and with a smart phone can control the brightness of the LED as well as an electronic door lock. By connecting an infrared (IR) transmitter module to the Raspberry Pi, we can control home appliances, such as an air conditioner, and we can also monitor indoor images, indoor temperatures, and illumination by using a smart phone app. We developed a method of finding out IR transmission codes required for remote-controllable appliances with an AVR micro-controller. We suggest a method to remotely open and shut an office door by novating the door lock. The brightness level of an LED (between 0 and 10) can be controlled through a PWM signal generated by an ATmega88 microcontroller. A mutiple-tap is controlled using an ATmega32, a photo-coupler, and a TRIAC. The signals for measured temperature and illumination are converted from analog to digital by using the ATtiny44A microcontroller transmitting to a Raspberry Pi through SPI communication. Then, we connect a camera to the CSI head of the Raspberry Pi. We can turn on the smart multiple-tap for a certain period of time, or we can schedule the multi-tap to turn on at a specific time. To reduce standby power, people usually pull out a power code from multiple-taps or turn off a switch. Our method helps people do the same thing with a smart phone, if they are away from home.