• 시스템엔지니어링학술지
• /
• 제16권2호
• /
• pp.16-26
• /
• 2020

Improving operator performance in complex and time-critical situations is critical to maintain plant safety and operability. These situations require quick detection, diagnosis, and mitigation actions to recover from the root cause of failure. One of the key challenges for operators in nuclear power plants is information management and following the control procedures and instructions. Nowadays Digital Twin technology can be used for analyzing and fast detection of failures and transient situations with the recommender system to provide the operator or maintenance engineer with recommended action to be carried out. Systems engineering approach (SE) is used in developing a digital twin for the CEDM system to support operator actions when there is a misalignment in the control element assembly group. Systems engineering is introduced for identifying the requirements, operational concept, and associated verification and validation steps required in the development process. The system developed by using a machine learning algorithm with a text mining technique to extract the required actions from limiting conditions for operations (LCO) or procedures that represent certain tasks.

• 한국소음진동공학회논문집
• /
• 제19권8호
• /
• pp.843-849
• /
• 2009

The reliable operation of a swing check valve in the main feed water system of a power plant is most essential for successful shout-down process. A failure to close the valve at proper time often leads to the instability of the main feed water system, or even to an emergency stop of the power plant. In reality it is a very difficult task to monitor the behavior of a swing check valve. Furthermore it is impossible to see the motion of the valve. In this work two measurements were carried out simultaneously to determine the precise valve closure time. The dynamic pressure measurements were made at the inlet and outlet regions of the swing check valve. The transient vibration of the valve housing in the direction of water flow was also measured, which enabled the measurement of the transient vibration of the valve housing near valve closure. By comparing the results produced from these measurements the precise valve closure time could be determined. By carrying out order tracking technique using the dynamic pressure signals and pump rpm signal, the complicated dynamic problems inside the main feed water system can be more easily dealt with. This measurement scheme might be implemented in a power plant on a real-time basis without much difficulty. If this could be implemented, valuable information essential for shut-down operations can readily be passed on to the main control room. The feasibility of this implementation was demonstrated by this experimental work.

• 한국전기전자재료학회논문지
• /
• 제33권2호
• /
• pp.130-134
• /
• 2020

Metal oxide varistors (MOVs) protect circuits and devices from transient overvoltages in electric power systems. However, a MOV continuously deteriorates owing to manufacturing defects or repetitive protective operations from transient overvoltages. A deteriorated MOV may result in a short circuit or a line-ground accident. Previous studies focused on the analysis of deterioration mechanisms and condition diagnosis techniques for MOVs owing to their recent growth of use. An accelerated deterioration experiment under the same conditions in which a MOV operates is essential. In this study, we designed and fabricated a surge generator that can apply a surge current to a MOV connected to AC mains. The coupling network operates at a low impedance against the surge current from the surge generator and transfers the surge current to the MOV under test. It also acts as a high impedance against AC mains for the AC voltage not to be applied to the surge generator. The decoupling network operates at a high impedance against the surge current and blocks the surge current from AC mains. It also acts as a low impedance against AC mains for the AC voltage to be applied to the MOV under test. The prototype surge generator can apply the 8/20 us up to 15 kA on AC voltages in the approximate range of 110~450 V, and it fully operates on a LabVIEW-based program.

• 한국추진공학회지
• /
• 제17권6호
• /
• pp.113-119
• /
• 2013

발사체 연소기용 산화제 개폐밸브는 비교적 간단한 개폐 작동을 통해, 액체산소를 연소기에 공급 또는 차단한다. 고압, 고유량, 극저온의 액체산소를 운용 유체로 사용할 뿐만 아니라, 설계유량 대비 밸브 차압 또한 낮아야 하는 상당히 까다로운 개발요구조건을 가지고 있다. 본 논문에서는 현재 개발 중인 연소기용 산화제 개폐밸브의 밸브 과도 응답과 같은 기본적인 밸브 특성과 함께, 밸브 성능을 좌우하는 핵심 부분이라고 할 수 있는 밸브 공압 구동부 및 포핏/시트부의 개발 내용을 소개하였다. 밸브의 과도 응답 특성 해석 결과가 시험 측정결과와 매우 잘 일치하는 것을 확인하였으며, 구동 공압부 및 포핏/시트부 구조해석을 통해 밸브 무빙파트의 접촉면 반발력과 마찰력을 정량적으로 평가하였다.

• Journal of Chest Surgery
• /
• 제18권2호
• /
• pp.165-173
• /
• 1985

A clinical analysis was performed n 706 uses of patent ductus arteriosus experienced at Department of Thoracic and Cardiovascular Surgery, Seoul National University Hospital during 27 years period from 1958 to 1984. Of the 706 patients of PDA, 244 patients were male and 462 patients were female and ages ranged from 2 months to 53 years old with the average age of 8.5 years. The chief complaints on admission were dyspnea on exertion and frequent URI in 58.9%, non specific symptoms such as palpitation and easy fatigability in 9.7%, symptoms of CHF in 2.0% and no subjective symptoms in 29.4%. On auscultation of heart, continuous machinery murmurs were heard in 82% and only systolic murmurs were heard in 18% of patients. On simple chest PA of patients, cardiomegalies were detected in 78% and there were increased pulmonary vascularities in 93% of patients. EKG findings were as followed; LVH 56.9%, BVH 12.6%, RVH 2.9% and WNL 27.6%. Cardiac Catheterizations were performed in 512 patients and mean Qp/Qs was 2.56 and mean systolic pulmonary artery pressure was 45mmHg. Operation methods were as followed; in patients in whom operations were performed on PDA only, ligation 94.3%, division 3.7% and ligation [0.5%] or trans-pulmonary artery suture closure [1.5%] under cardiopulmonary bypass 2.0% and in patients in whom operations were performed with associated anomalies, ligation 17.6%, division 2.4%, and ligation [44.7%] or trans-pulmonary artery suture closure [35.3%] under cardiopulmonary bypass 80%. 52 postoperative complications [8.4%] were developed in 42 patients [6.8%] and its were as followed; permanent or transient hoarseness 16 [2.6%], intraoperative rupture of PDA 8 [1.3%], recannalization 6 [1.[%], operative death 5 [0.8%], late death 4 [0.6%] and other miscellaneous complications 13 [2.1%]. 140 associated cardiac anomalies [19.8%] were found in 105 patients [14.9%] and its were as followed; VSD 68 [9.6%], COA 15 [2.1%], Subaortic discrete membrane 7 [0.9%], ASD 6 [0.8%], TOF 5 [0.7%] and other miscellaneous and

• 한국환경과학회지
• /
• 제22권9호
• /
• pp.1115-1129
• /
• 2013

The study area is located on the western coast, and the inner development construction has been ongoing since 2011. The purposes of current study are to effectively simulate and quantitatively predict a temporal and spatial distributions of water temperature and salinity due to the stages of inner development construction in saemangeum reclaimed area. The transient-state numerical modeling using EFDC model is done, and the numerical simulation results are validated reasonably by repetitive numerical model calibration procedures with respect to field measurements of water temperature and salinity. The spatial distributions of water temperature and salinity show similar trends before and after construction of the dikes. In spring season, the salinity has maximum value of 21 psu, while, in summer season, the salinity shows 7 psu in a whole modeling domain. Thus, it is clearly observed that salt water is replaced by freshwater. However, the salinity and temperature reach their initial conditions at the end of the year. The salinity after construction of the dikes is lower than that before construction of them at Mankyeong area. On the other hands, after construction of the dikes, the salinity after dredging operations is higher than that before dredging. Because drastical increasing of water volume in Saemangeum Lake leads to increasing of stagnation time at bottom layer, and salt water is easily intruded to the two estuaries. Therefore, it may be concluded that hydrodynamic characteristics on Saemangeum are dominated by either Mankyeong and Dongjin discharge or sluice gates in/out-flow amounts, and thus they must be properly considered when rigorous and reasonable predictions of water temperature and salinity according to the stages of inner development construction.

• Journal of Chest Surgery
• /
• 제50권1호
• /
• pp.36-40
• /
• 2017

Background: Surgical treatment of thoracic outlet syndrome (TOS) is necessary when non-surgical treatments fail. Complications of surgical procedures vary from short-term post-surgical pain to permanent disability. The outcome of TOS surgery is affected by the visibility during the operation. In this study, we have compared the complications arising during the supraclavicular and the transaxillary approaches to determine the appropriate approach for TOS surgery. Methods: In this study, 448 patients with symptoms of TOS were assessed. The male-to-female ratio was approximately 1:4, and the mean age was 34.5 years. Overall, 102 operations were performed, including unilateral, bilateral, and reoperations, and the patients were retrospectively evaluated. Of the 102 patients, 63 underwent the supraclavicular approach, 32 underwent the transaxillary approach, and 7 underwent the transaxillary approach followed by the supraclavicular approach. Complications were evaluated over 24 months. Results: The prevalence of pneumothorax, hemothorax, and vessel injuries in the transaxillary and the supraclavicular approaches was equal. We found more permanent and transient brachial plexus injuries in the case of the transaxillary approach than in the case of the supraclavicular approach, but the difference was not statistically significant. Persistent pain and symptoms were significantly more common in patients who underwent the transaxillary approach (p<0.05). Conclusion: The supraclavicular approach seems to be the more effective technique of the two because it offers the surgeon better access to the brachial plexus and a direct view. This approach for a TOS operation offers a better surgical outcome and lower reoperation rates than the transaxillary method. Our results showed the supraclavicular approach to be the preferred method for TOS operations.

• 한국전자통신학회논문지
• /
• 제16권4호
• /
• pp.633-642
• /
• 2021

제한적인 탄소배출의 필요성과 연계되는 전력수요 증가는 재생에너지산업에서 폭발적인 상승을 가져오고 있다. 전력계통에서 전기공급은 항상 전기수요와 균형을 맞추어야 할 필요가 있고, 안전하고 믿을만한 안정적인 운영을 유지하기 위하여 계통손실이 발생한다. 높은 비율의 재생에너지 보급을 갖는 전력계통에서 과도 안정도, 미소신호 안정도 및 주파수 안정도와 같은 넓은 범위의 3가지의 난제가 있다. 과도안정도는 선로계전기 동작이나 발전기 탈락과 같은 장애에 대한 계통응답을 해석하는 것이다. 미소신호 안정도는 계통관성 저하에 따른 전압불안정, 주파수 급변, 전력진동 등이 발생가능한 계통에서 조그만 증분같은 작은 동요가 일어날 때 전력계통 동기를 유지하기 위한 계통의 기능이다. 주파수 안정도는 발전과 부하 사이에 심한 불균형이 발생하는 중대 계통혼란에서도 정상 주파수를 유지하기 위한 전력계통의 기능으로 간주한다. 본 논문에서 재생에너지 보급계획에 따른 계통모의를 수행하여 3종류 안정도를 검토하며, 또한 재생에너지원이 계통안정도에 미치는 영향을 분석한다.

• Journal of Power Electronics
• /
• 제4권1호
• /
• pp.39-45
• /
• 2004

A novel current-fed energy-recovery sustaining driver (CFERSD) for a PDP is proposed in this paper. Its main idea is to recover the energy stored in the PDP or to inject the input source energy to the PDP by using the current source built-up in the energy recovery inductor. This method provides zero-voltage-switching (ZVS) of all main power switches, the reduction of EMI, and more improved operational voltage margins with the aid of the discharge current compensation. In addition, since the current flowing through the energy recovery inductor can compensate the plasma discharge current flowing through the conducting power switches, the current stress through all main power switches can be considerably reduced. Furthermore, it features a low conduction loss and fast transient time. Operations, features and design considerations are presented and verified experimentally on a 1020${\times}$l06mm sized PDP, 50kHz-switching frequency, and sustaining voltage 140V based prototype.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2008년도 춘계학술대회 논문집
• /
• pp.178-181
• /
• 2008

Cylindrical stainless-steel/sodium heat pipe for a high-temperature application was manufactured and tested for transient and steady-state operations. The container material was made of stainless-steel 316, and the working fluid was sodium. Stainless-steel 316 mesh screen was inserted as a capillary structure. The working fluid fill charge ratio was approximately 64 $\sim$ 181% based on the pore space of the wick. The outer diameter of the heat pipe was 12.7 mm and the total length was 250 mm. The evaporator part was 150 mm and the condenser 80 mm. The performance test of the heat pipe has been conducted in the furnace with up to 800 W. The variation of the average heat transfer coefficient was investigated as a function of heat flux and vapor temperature. As input thermal load increased, it was showed that difference of temperatures in evaporator and condenser decreased and that operating section and heat transfer characteristics at the heat pipe increased.