• 대한기계학회논문집
• /
• 제18권3호
• /
• pp.548-554
• /
• 1994

The high temperature fatigue crack growth behavior of SUS 304 stainless steel at $550^{\circ}C$ and $650^{\circ}C$ was investigated under various kinds of stress ratio and frequency in sinusoidal waveform on the basis of the non-linear fracture mechanics. The result arranging crack growth rate by modified J-integral J' showed influence of stress ratio and frequency. All the data obtained under the test at $550^{\circ}C$ were plotted within data band of da/dN-${\triangle}J_f$ relationship for cycle-dependent crack growth. On the basis of static creep and cycle-dependent data band; both time- and cycle-dependent crack growth behavior was observed under loading conditions at $650^{\circ}C$, but cycle-dependent crack growth behavior predominantly appeared and time-dependent crack growth behaviour was little observed under loading conditions at $550^{\circ}C$. Fractographic examinations for fracture surface indicated that the fracture mode was generally transgranular. The stripes were found on fracture surface and each stripe was accompanied by a crack tip blunting and an abrupt increase in the load-point displacement. The $J'_{an}$ had a validity in case of $650^{\circ}C, but scarcely had it in case of $550^{\circ}C$.

• 한국결정성장학회지
• /
• 제10권2호
• /
• pp.122-127
• /
• 2000

불규칙 입자형성을 갖는 Ce-TZP와 알루미나가 분산된 Ce-TZP 세라믹스를 세라아 도핑조선과 열처리 조건을 변화시켜 제조한 다음, 미세구조를 관찰하였다. 제조된 시편들은 상대밀도가 99% 이상인 고밀도의 소결체였으며, 정방정 및 입방정상 지르코니아 입자로 구성되었다. 도핑하지 않거나 소결만 시킨 시편의 경우 직선적인 입계와 정상적인 입자형성을 나타낸데 비하여 세리아를 침적법으로 도핑한 후 고온으로 열처리한 시편에서는 확산구동 입계이동이 일어나 입계 및 입자형성이 불규칙하였으며. 이러한 Ce-TZP에서는 입자당 평균 입계같이 정상입자에 비하여 크게 증가하였다. 알루미나를 분산시켜 소결한 {{{{ { Al}_{2 }{ O}_{3 } }}}}/Ce- TZP 시편의 경우, 알루미나 입자에 의해서 입성장이 크게 억제되었고, 세리아를 도핑한 후 소결과 열처리를 행한 {{{{ { Al}_{2 }{ O}_{3 } }}}}/Ce-TZP에서는 불규칙 입자형상이 형성되면서도 입성장이 억제되어 입자크기에 비하여 입계면적이 크게 증가하였다. 분산된 알루미나 입자들은 소결과 열처리 과정 중 입자크기가 증가하였고, 열처리 동안 많은 입자들이 입계에서 입내로 위치가 변화하였다. 정상적인 입자형성을 갖은 시편에서는 균열진전시 입계파괴가 주로 일어났으나 불규칙 입자형성을 갖는 시편에서는 주로 입내파괴가 관찰되었다.

• 대한기계학회논문집A
• /
• 제24권2호
• /
• pp.303-310
• /
• 2000

Fracture toughness of five different reactor pressure vessel steels was characterized in the transition temperature region by the ASTM E1921-97 standard method using Charpy-sized small specimens. T he predominant fracture mode of the tested steels was transgranular cleavage in the test conditions. A statistical analysis based on the Weibull distribution was applied to the interpretation of the scattered fracture toughness data. The size-dependence of the measured fracture toughness values was also well predicted by means of the Weibull probabilistic analysis. The measured fracture toughness transition curves followed the temperature-dependence of the ASTM master curve within the expected scatter bands. Therefore, the fracture toughness characteristics in the transition region could be described by a single parameter, so-called the reference temperature (T。), for a given steel. The determined reference temperatures of the tested materials could not be correlated with the conventional index temperatures from Charpy impact tests.

• 한국재료학회지
• /
• 제10권5호
• /
• pp.321-327
• /
• 2000

다공성 알루미나 소결체내부로 3Y-TZP 및 12Ce-TZP 전구체를 각각 액상침투시킴으로써 2종류의 $Al_2O_3/TZP$복합체를 제조하였다. 소량의 (~11.0 wt%) TZP의 첨가는 Al2O3소결체 ($1600^{\circ}C$, 2시간)의 강도 (19~59%)와 파괴인성(14~157%)을 증가시켰다. 3Y-TZP의 첨가는 복합체의 강도의 향상에 12Ce-TZP의 첨가는 인성의 향상에 보다 효과적이었다. 침투도니 TZP는 복합체의 내부보다 표면에 집중되었으며, 그 결과 이곳에서의 입성장에 빨랐고 $Al_2O_3$의입성장 억제효과도 상대적으로 뛰어났다. 입계 및 입내균열전파가 일어났으나 $Al_2O_3/12Ce-TZP$의 경우가 $Al_2O_3/3Y-TZP$에 비하여 입계파괴가 우세하였다

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2011년도 제42회 하계학술대회
• /
• pp.1515-1516
• /
• 2011

Conductive SiC-$ZrB_2$ composites were produced by subjection a 40:60(vol%) mixture of zirconium diborided ($ZrB_2$) powder and ${\beta}$-silicon carbide (SiC) matrix to spark plasma sintering (SPS) under argon atmosphere. Inner diameters of graphite mold were $15mm{\varphi}$ and $20mm{\varphi}$, respectively. The relative densities of $15mm{\varphi}$ and $20mm{\varphi}$ sample were 99.4% and 97.88%, respectively. Reactions between ${\beta}$-SiC and $ZrB_2$ were not observed via x-ray diffraction (hereafter, XRD) analysis. The result of FE-SEM of fracture face of $15mm{\varphi}$ sample was intergranular fracture and that of $20mm{\varphi}$ sample was transgranular fracture. Because the fracture strength of $15mm{\varphi}$ sample was much higher than that of $20mm{\varphi}$ sample. The electrical resistivity, $9.37{\times}10^{-4}{\Omega}{\cdot}cm$ of $15mm{\varphi}$ sample was higher than that, $6.17{\times}10^{-4}{\Omega}{\cdot}cm$ of $20mm{\varphi}$ sample because of densification. Although sintering condition of SPS is same. the properties of sintered SiC-$ZrB_2$ compacts were changed according to inner diameter of graphite mold.

• 한국가스학회지
• /
• 제5권1호
• /
• pp.1-6
• /
• 2001

고강도 알루미늄 합금 2024-T3와 모제 시험편과 부식 시험편을 사용하여 피로 균열 진전증에 발생하는 음향방출 신호를 검출 분석하였다. 시험편 조건에 관계없이 5종류의 신호가 관찰되었다. 모재에서 얻어진 신호는 피로하중을 받으므로서 균열 발생 초기 노치선단외 돌출과 함몰에 의한 높은 에너지를 가진 짧은 기간의 입내 파괴 신호이며, 부식 시험편은 피트 선단 근처의 결정경계의 치화로 인하여 입계 파괴 신호이다. 따라서, 파형과 파워 스펙트럼은 시험편 조건에 의존하는 것 같다. 시험편 조건에 의한 파형과 파워 스펙트럼을 해석함으로써 구조부재의 다향한 손상과 결함으로부터 발생하는 균열 전파와 최종 파괴과정의 실시간 감시 가능하다

• 한국주조공학회지
• /
• 제21권6호
• /
• pp.336-342
• /
• 2001

This study was carried out to examine the effects of adding 0.3at.%Hf in Fe-30at.%Al-5at.%Cr alloy on the variation of microstructures and hot workability. The effect of hot rolling on mechanical properties was estimated by measuring the elongation and tensile strength after rolling at 800 and 1000 respectively. Microstructure of Fe-30at.%Al-5at.%Cr alloy was consisted of large equiaxed grains and it was changed to quasi-equiaxed or columnar structures by adding 0.3at.%Hf to Fe-30at.%Al-5at.%Cr alloy. Every specimens showed a decreased tensile strength after hot rolling compared to that of before rolling. The elongation was increased by hot rolling. Remarkable changes in elongation by hot rollong was observed such as from 1.4% to 4.5% elongation at the specimen of 0.3at.%Hf added to Fe-30at.%Al-5at.%Cr. Fe-30at.%Al-5at.%Cr alloy showed typical cleavage fracture on tensile failure and hot rolling has negligible effects on fracture mode in this alloy. However at the alloy containing Hf fracture mode was changed by hot rolling from intergranular to mixed intergranular and transgranular fracture mode.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집A
• /
• pp.223-230
• /
• 2001

The Monkman-Grant (M-G) and its modified parameters were estimated for modified type 316LN and $9{\sim}12Cr-1Mo$ steels with chemical variations. Several sets of creep data were obtained by constant-load creep tests in $550-650^{\circ}C$ ranges. The relation parameters, m, $m^*$, C and $C^*$ were proposed and discussed for two alloy systems. In creep fracture mode, type 316LN steel showed domination of the intergranular fracture caused by growth and coalescence of cavities. On the other hand, the Cr-Mo steel showed transgranular fracture of the ductile type caused from softening at high temperature. In spite of the basic differences in creep fracture modes as well as creep properties, the M-G and its modified relations demonstrated linearity within the $2{\sigma}$ standard deviation. The value of the m parameter of the M-G relation was 0.90 in the 316LN steel and 0.84 in the Cr-Mo steel. The value of the $m^*$ parameter of the modified relation was 0.94 in the 316LN steel and 0.89 in Cr-Mo steel. The modified relation was superior to the M-G relation because the $m^*$ slopes almost overlapped regardless of creep testing conditions and chemical variations to the two alloy systems.

• 한국재료학회지
• /
• 제10권7호
• /
• pp.505-514
• /
• 2000

플라즈마 침탄한 저 탄소 Cr-Mo 강(0.176C-1.014Cr-0.387Mo)의 침탄 특성과 피로성질을 고찰하였다. 플라즈만 침탄한 시편의 유효경화깊이는 가스 침탄한 시편에 대해 상대적으로 침타나시간이 짧고 침탄온도가 낮음에도 불구하고 50%정도까지 증가되었다. 플라즈만 침탄시 유효경화깊이의 증가는 표면탄소농도의 증가와 같은 경향을 보였으며, 표면탄소농도의 증가와 같은 경향을 보였으며, 표면탄소농도의 증가율이 침탄시간의 증가에 따라 감소하였다. 플라즈만 침탄간의 피로한도는 가스 침탄강의 경우보다 높았다. 이를 표면근처의 미세구조, 경화깊이 잔류, 오스테나이트와 압축잔류응력으로 조사한 결과 경화깊이와 압축잔류응력의 차이가 거의 없었다. 따라서 플라즈만 침탄의 피로강도 향상은 가스침탄에 비해 표면이 상승층이 저감되어 표면에서의 미소균열의 발생 및 초기 균열 전파과정이 지연 되어진 것으로 판단된다. 파단면 관찰결과 표면에서 균열이 시작되고 플라즈마 침탄의 경우 입내파괴가 현저하였다.

• 소성∙가공
• /
• 제17권4호
• /
• pp.240-248
• /
• 2008

The effect of alloying elements(Mn, S, Mo, B) on the high temperature deformation behavior of Fe-29%Ni-17%Co (Kovar) alloy were investigated. And the effect of high temperature oxidation on the hot ductility was also studied. The hot ductility of Kovar alloy was drastically increased with the addition of Mn and lowering of S content. It has been found that the brittle intergranular fracture at high temperature cracking is closely associated with the FeS sulfide along the grain boundary. When Mn was added, the type of sulfide was changed to MnS from FeS and ductile intergranular fracture and transgranular fracture were promoted. The formation of oxide layer was found to have minimized the hot ductility of the Kovar alloy significantly. Grain boundary micro-cracks in the internal oxide region were noted following deformation due to high temperature, one of which acting as a notch that caused the poor hot workability of the oxidized specimen. The addition of Mo to the Kovar alloy could also retard the decrease in the hot ductility of the oxidized specimen through the prevention of notching due to internal oxidation. Hot ductility was remarkably improved by the addition of Boron. The improvement of hot ductility results from the grain boundary migration mainly due to the dynamic recrystallization at lower temperature range ($900{\sim}1000^{\circ}C$).