• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.1258-1263
• /
• 2004

The present study proposes a new structure for a heat spreader which could embody a thin thickness, any shapes and high heat flux per unit area. It is on the structure for the formation of vapor passages and the support of the case of the heat spreader. A screen mesh is used as the one. To verify the validity of the one, the heat spreader of 1.4mm and 1.6mm thickness was made with 14 mesh and 100 mesh number. In this paper, The performance test of heat spreader conducted in order to compare with the heat transfer performance of conventional heat pipe. As the results, The heat spreader has excellent cooling and heat transfer performance.

• Archives of Reconstructive Microsurgery
• /
• v.11 no.1
• /
• pp.41-46
• /
• 2002

Purpose : To assess the clinical results of second toe-to-finger transfer in traumatic amputated index finger. Materials and Methods : For the clinical evaluation, we have analyzed 12 patients with ROM of finger joints, pinch power, static two point discrimination, life functional assessment, and patient's satisfaction. Results : In genral ROM was $54.4^{\circ}$ at MP joint, $17^{\circ}$ at PIP joint and $6.7^{\circ}$ at DIP joint. Pinch power was good in 3 cases, fair in 7 cases, and poor in 2 cases. Daily life activity and patient's acceptance were satisfactory. Conclusion : Although transfered toe function may be poorer than normal finger, the hand was restored to a useful, sensate and versatile functional unit.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.23 no.4
• /
• pp.290-293
• /
• 2018

This paper proposes a new magnetic resonant wireless power transfer system. Two transmitters are arranged to secure a range wider than the existing one-to-one resonance, thereby enhancing the practicality of the system. Two identical transmission units are arranged to strengthen the magnetic field and to subsequently increase the magnitude and distance of the power transmitted to the reception unit. A constant power can be maintained in a wide range through the phase control of different output powers according to the positions of the transmitting and receiving coils. A constant power can also be obtained by transmitting to the receiver. The experiment results show that the proposed method outperforms the conventional method.

• Proceedings of the Korean Operations and Management Science Society Conference
• /
• 1996.04a
• /
• pp.234-241
• /
• 1996

Trip-based material handling systems such as AGV systems, lift trucks, etc. are often designed with a given flow matrix (or FROM-TO chart) which is usually treated as the number of loaded trips that the devices must perform per unit time between the stations. In reality, the number of trips that would result from parts flow in a facility is dictated by the transfer batch size, i.e., the number of parts that are transferred from one station to the next in one trip. In this paper, we present analytical and simulation results aimed at determining optimal or near-optimal transfer batch sizes in manufacturing systems.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1995.10a
• /
• pp.93-102
• /
• 1995

In this study the characteristics of adiabatic and lightweight of cement mortar was improved by using porous Bottom ash which was industrial waste. when a foaming agent was added, the characteristics of mortar using sand and Bottom ash were compared. From the empirical results the heat-transfer ratio for the mortar using Bottom ash only was shown the lower values than that for a general mortar, and the lightweight concrete with unit weight of 1.5t/$\textrm{m}^3$ could be made. When the foaming agent of 0.25% and 0.5% in usage of cement was added to that, the compressive strength scould be measured as 5 and 8times of the general mortar respectively. Also, the characteristics of adiabatic for that mortar was great improved so that the heat-transfer ratio was fallen to 0.172kcal/$mh^{\circ}C$.

• ETRI Journal
• /
• v.34 no.4
• /
• pp.553-563
• /
• 2012

Serial peripheral interface (SPI) has been identified as a bottleneck in many wireless sensing systems today. SPI is used almost universally as the physical connection between the microcontroller unit (MCU) and radios, storage devices, and many types of sensors. Virtually all wireless sensor nodes today perform up to twice as many bus transactions as necessary to transfer a given piece of data, as an MCU must serve as the bus master in all transactions. To eliminate this bottleneck, we propose the master-handoff protocol. After the MCU initiates reading from the source slave device and writing to the sink slave device, the MCU as a master becomes a slave, and either the source or the sink slave becomes the temporary master. Experiment results show that this master-handoff technique not only cuts the data transfer time in half, but, more importantly, also enables a superlinear energy reduction.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2003.10a
• /
• pp.83-86
• /
• 2003

Complete prediction of second order permeability tensor for three dimensional preform such as plain woven fabric and braided preform is critical to understand the resin transfer molding process of composites. The permeability can be obtained by various methods such as analytic, numerical, and experimental methods. For several decades, the permeability has studied numerically to avoid practical difficulty of many experiments. However, the predicted permeabilities are a bit wrong compared with experimentally measured data. In this study, numerical calculation of permeability was conducted for two kinds of preforms i.e., plain woven fabric and circular braided preform. In order to consider intra-tow flow in the unit cell of preform the proposed flow coupled model was used for plain woven fabric and the Brinkman equation was solved in the case of the braided preform.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.1566-1571
• /
• 2003

The cold plate used for a CEU(Control Electronics Unit) of an EV(Electric Vehicle) is extremely important since the dissipation of the heat generated from power devices like IGBT(Insulated Gate Bipolar Transistor) and diode has a significant effect on the performance as well as the durability of the CED. The cold plate consists of seven power devices, and coolant flows through the passage bonded to a groove of the cold plate. In order to find out heat transfer and pressure drop characteristics, series of numerical analyses for the cold plate with enhanced coolant passages were conducted. Based on results of the numerical analyses, an improved model of the cold plate has been proposed. The experiments under the various conditions have been conducted to compare the performance of the proposed cold plate to the present one. As a result of the numerical analyses together with the experiments, the ideal design of the cold plate could be offered.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.317-318
• /
• 2006

A transfer loading system for 21' RF band assembly box was developed in the present study. The weight of a box is approximately 60kgf End total weight of one day job per person is about $4,000kg_f$. For an efficient design and manufacturing process, three dimensional design and engineering technique were applied to the presented system. Motion analysis for a popup unit and structural analysis for belt part subjected to the load of box weight were performed, respectively. It was found that the evasion of duty and labor intensity is reduced after appling the developed system to manufacturing field of small and midium business.

• Proceedings of the SAREK Conference
• /
• 2008.06a
• /
• pp.408-413
• /
• 2008

This study presents comparison of the air side heat transfer and friction characteristics in a heating condition between Louver fin-tube heat exchangers and aluminum heat exchangers. Experiments are performed for the Louver fin-tube heat exchangers and aluminum heat exchangers using a calorimeter, which is designed based on air-enthalpy method described in ASHRAE standards. The air velocities its are varied from 0.7 to 1.6 m/s with 0.3 m/s interval. A study result shows that the heat transfer performances of aluminum heat exchangers are $40{\sim}80%$ higher than those of Louver fin-tube heat exchangers per unit volume, mass and heat transfer area.