• Journal of Advanced Marine Engineering and Technology
• /
• v.29 no.8
• /
• pp.883-890
• /
• 2005

The industrial growth and the raised living quality have led to the massive energy consumption. As a result. the polluted environment and the limited amount of energy resources emerged as serious problems to be resolved in 21st century. Especially, in the case of Korea whose imported energy dependency rate is 98.2$\%$ in 2003 and constantly increasing every rear. more than 24$\%$ of overall energy consumption is for housing and commercial use. In order to cope with the shortage of natural energy resources, it is inevitable to develop alternative sustainable energy resources including seawater heat. so that they can replace existing resources. The heat transfer air velocity 3.5 m/s is proper to consideration with the body the pipe size 200A is more suitable than look due to the air velocity quantify and the ratio of pipe surface area. And the error between experimental data with simulation is below 5.34$\%$ so the suggested equation for calculating heat transfer capacity can be used. Therefore out of many methods utilizing seawater heat. this work Presents the efficiency of using sea water heat as a resource for air-conditioners which can be converted from the outside air through the air-to-heat conversion tube . Consequently. this method provides pretty reasonable energy efficiency.

• Structural Engineering and Mechanics
• /
• v.16 no.1
• /
• pp.17-34
• /
• 2003

This paper presents a damage assessment procedure applied to periodic spring mass systems using an eigenvalue sensitivity-based method. The damage is directly related to the stiffness reduction of the damage element. The natural frequencies of periodic structures with one single disorder are found by adopting the transfer matrix approach, consequently, the first order approximation of the natural frequencies with respect to the disordered stiffness in different elements is used to form the sensitivity matrix. The analysis shows that the sensitivity of natural frequencies to damage in different locations depends only on the mode number and the location of damage. The stiffness changes due to damage can be identified by solving a set of underdetermined equations based on the sensitivity matrix. The issues associated with many possible damage locations in large structural systems are addressed, and a means of improving the computational efficiency of damage detection while maintaining the accuracy for large periodic structures with limited available measured natural frequencies, is also introduced in this paper. The incomplete measurements and the effect of random error in terms of measurement noise in the natural frequencies are considered. Numerical results of a periodic spring-mass system of 20 degrees of freedom illustrate that the proposed method is simple and robust in locating single or multiple damages in a large periodic structure with a high computational efficiency.

• Proceedings of the KSME Conference
• /
• 2002.08a
• /
• pp.115-118
• /
• 2002

The present study deals with CFD analysis of a plastic heat exchanger with corrugated wall. This exchanger has sinusoidal corrugations, and the flow through the exchanger is three dimensional. In addition, CFX-5.4, a commercial code utilizing unstructured mesh, was used as a computational method for solving RANS(Reynolds-Averaged Navier-Stokes) equations, and the applied turbulence model is $k-{\varepsilon}$ model. The factors to affect the efficiency of a plastic heat exchanger are heat conductivity, flow characteristics and so on. For those two factors, heat conductivity is fixed by the wall material. Therefore, the How along the corrugation affects the efficiency more, provided the same material. In conclusion, the heat transfer enhancement of a plastic heat exchanger with corrugated wall can be recognized from the flow characteristics such as velocity streamline, local heat transfer coefficient, velocity contour, and pressure contour. To confirm the results, both of the measured and the computational data for pressure loss were compared with each other, and they were identical.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.11
• /
• pp.2189-2195
• /
• 1992

The performance of heat exchanger as an energy conversion device can be described by the available energy output and efficiency. The efficiency is defined as the ratio of the available energy output and the exergy of the heat source flow. In present study, a counterflow heat exchanger is analyzed and the conditions to obtain maximum output is numerically determined. As a result, the avilable energy obtained by the cold flow can be determined as functions of the heat capacity flow, the cold flow inlet temperature and the heat transfer capacity of heat exchanger. At the maximum output condition the heat capacity flow of the cold fluid is larger than that of the heat source, and the heat capacity flow ratio is equal to the ratio of the cold flow inlet temperature and the atmospheric temperature. And the avilable energy output increases as the heat transfer capacity of the heat exchanger become larger, but in the economic point of view there is also an optimum heat transfer capacity for a given heat source flow.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.12
• /
• pp.41-45
• /
• 2015

In this paper, the single port dual-band resonator for magnetic resonance wireless power transfer is proposed. The proposed dual-band resonator is consists of 20 turns spiral coil, a single loop, matching circuit, lumped elements, and a single port. The two sides of the matching circuit are connected to via holes. The spiral coil is operated at MF-band and single loop is operated at HF-band, respectively. We use two of the same structure resonators and simulated and the power transfer efficiency was calculated. The efficiency of simulation and measurement is above 60% at the MF and HF bands, and the distance is 100 mm.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.10
• /
• pp.1-5
• /
• 2011

A magnetic resonant coil system for enhancement of wireless power transfer efficiency of NFC devices was proposed. The NFC system consists of resonant coils arrange between source coil and device coil. The effects of resonant coil was measured using a 13.56MHz RFID reader and tag system and simulated by 3D RF simulator. The measurement results from RFID reader and tag show that the maximum distance of signal transmission is increased by 96.72% and received voltage of RFID tag is grew by 17.95% thanks to the magnetic resonant coils.

• Advances in environmental research
• /
• v.2 no.1
• /
• pp.1-8
• /
• 2013

There is a significant demand to make various dissolved gases in water. However, the conventional aeration method shows low gas mass transfer rate and gas utilization efficiency. In this study, a novel rotating wheel entraining gas method was developed for making high dissolved $O_2$ and $O_3$ in water. It produced higher concentration and higher transfer rate of dissolved $O_2$ and $O_3$ than conventional bubble aeration method, especially almost 100% of gas transfer efficiency was achieved for $O_3$ in enclosed reactor. For application of rotating wheel entraining gas method, aerobic bio-reactor and membrane bio-reactor (MBR) were successfully used for treatment of domestic and pharmaceutical wastewater, respectively; and vacuum ultraviolet $(VUV)/UV+O_3/O_2$ reactors were well used for sterilization in air/water, removal of dust particles and toxic gases in air, and degradation of pesticide residue and sterilization on fruits and vegetables.

• Journal of Embryo Transfer
• /
• v.15 no.1
• /
• pp.95-102
• /
• 2000

Techniques for manipulation of spermatozoa and oocytes have been widely used for in vitro production(IVP) of Hanwoo. This study was conducted to examine the effects of theophylline and heparin on frozen-thawed Hanwoo sperm for enhancing the efficiency of IVP technique. Oocytes were inseminated with forzen bull semen treated with either theophylline or heparin for examining the effect of each substance on fertilization and subsequent development. More (P<0.05) oocytes formed pronucleus and develop to the morula and blastocyst stages after inseminated with sperm treated with heparin than after inseminated with sperm treated with theophylline. The pregnancy rate after embryo transfer was higher after heparin treatment than after theophylline treatment, but did not differ significantly. There was no significant difference of offspring delivery between two groups. In conculsion, theophylline and heparin can be used for enhancing the efficiency of IVP system for Hanwoo. Considering characteristics of these substance, theophylline may be useful in the artificial insemination system, which requires vigorous sperm motility. While, heparin supporting sperm viability in vitro can be effectively used for improving in vitro-fertilization system.

• Journal of Biomedical Engineering Research
• /
• v.16 no.4
• /
• pp.447-456
• /
• 1995

As a part of electro-mechanical totally implantable artificial heart (TIAH) program, a transcut- aneous energy transmission system has been developed. By mutual magnetic induction between the first coil on the skin and the subcutaneously implanted second coil, the system transfers elctrical power through the skin. This research aimed at minimizing the size of the implanted part as well as maximizing the transfer efficiency. Using class I amplifier, we achieved above 75% power transfer efficiency at average 40W power transfer level which is required for normal TIAH operation. In vivo performance of the developed system and bio-compatibility of the material used in Implanted parts were evaluated through animal experiments.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.20 no.8
• /
• pp.547-555
• /
• 2008

The effects of paper properties such as density, air permeability, water vapor transmission rate on the thermal performance of plate-type enthalpy exchanger were experimentally investigated. Papers having different properties were made from the same pulp by calendering or refining. Enthalpy exchanger samples were made from the papers, and were tested according to the standard test procedure (KS B 6879). Effective efficiencies were obtained, which accounted for the air leakage between supply and exhaust streams. Results showed that paper density affected the sensible heat transfer of the samples. Sensible heat transfer increased with density of the paper. It was also shown that effective efficiency of latent heat transfer was approximately the same independent of the samples, which suggests that papers made of the same pulp show similar water vapor transmission characteristics independent of the degree of calendering or refining. Best performance was obtained for the sample having highest paper density and moderate water vapor transmission ratio.