• International Journal of Air-Conditioning and Refrigeration
• /
• v.9 no.3
• /
• pp.63-71
• /
• 2001

This paper presents a model-based method for detecting and diagnosing some faults in the cooling tower of healing, ventilating, and air-conditioning systems. A simple model for the cooling tower is employed. Faults in cooling tower operation are detected through the deviations in the values of system characteristic parameters such as the heat transfer coefficient-area product, the tower approach, the tower effectiveness, and fan power. Three distinct faults are considered: cooling tower inlet water temperature sensor fault, cooling tower pump fault, and cooling tower fan fault. As a result, most values of the system characteristics parameter variations due to a fault are much higher or lower than the values without faults. This allows the faults in a cooling tower to be detected easily using above methods. The diagnostic rules for the faults were also developed through investigating the changes in the different parameter due to each faults.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.20 no.7
• /
• pp.455-461
• /
• 2008

A reversed trapezoidal fin with variable fin base thickness is optimized using a two-dimensional analytical method. For the fin base boundary condition, instead of a constant temperature, heat transfer from the inside fluid to the fin base is considered. Heat loss from the fin tip is not ignored. The maximum heat loss, corresponding optimum fin effectiveness, fin length and base height are presented as a function of the fin base thickness, shape factor and volume.

• Journal of Bio-Environment Control
• /
• v.2 no.1
• /
• pp.1-8
• /
• 1993

Experimental and theoretical analyses were carried out to investigate the heat exchange characteristics of the nutrient solution cooling system utilizing ground water. The material of heat exchanger used in the experiment was polyethylene and the cross-flow type was adapted in which nutrient solution was mixed and ground water unmixed. For the exchanger surface area of 0.33$m^2$ and flow rates of ground water of 1-6$\ell$/min, NTU(number of transfer units) and effectiveness of experimental heat exchanger were 0.1-0.45 and 10-35％, respectively. Therefore these results showed that the hydroponic greenhouse of 1,000$m^2$(300 pyong) with the ground water of 10$m^2$/day could cover about 55-70％ of maximum cooling load in summer.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.15 no.8
• /
• pp.2944-2958
• /
• 2021

Today, online education is becoming more important. The effectiveness of online education has been measured by student satisfaction and the possibility of substituting offline education. This study proposes a plan to increase the effectiveness of education in a new form by using online information. Education is the process of socializing and growing learners. Representative negative emotions experienced by learners are stress, anxiety, and depression (SAD). A reduction in SAD will promote student growth and improve educational outcomes. This paper considers online information by dividing it into online educational information support (OEDIS) and online emotional information support (OEMIS). We demonstrate that OEDIS reduces SAD, and OEMIS reduces stress and anxiety. By providing online information, negative emotions can be reduced, and educational outcomes can be improved. This study suggests a new role for online information support, such as emotional change in individuals and solving psychological problems. Online information support goes beyond knowledge transfer and can be used in various fields, such as online education that promotes human growth and positive change, and even healthcare.

• KIEAE Journal
• /
• v.8 no.5
• /
• pp.11-16
• /
• 2008

This research has established CFD model on pit's cool-tube system through heat and air movement simulations, of which data was based on experimental and verification. This research work verified the effectiveness of the cool-tube system by analysing temperature, humidity and air current of the actually installed case. Also, we analysed heat transfer through air current simulation and the results are as followings. Firstly, we experiment on temperature, humidity and speed of air currents of the cool tube system with pit space during the month of May (spring). The average exterior temperature was $16.1^{\circ}C$, and $18.2^{\circ}C$ for the pit, $24.7^{\circ}C$ for the compressor room. Secondly, based on measured data of real case, we have analysed heat transfer through air current simulation and verified our proposed model. The actual measurement of average temperature of exhaust air of the pit's area is $19.7^{\circ}C$ with tolerance of $-0.33^{\circ}C{\sim}-0.6^{\circ}C$ compared to above simulations. Thirdly, having verified air current simulation model with formation of 260,000 and 1,000,000 cells, we could get reasonable near values with 260,000 cells. Lastly, the next step of research would be focused on proposing the best possible pit's cool-tube system after analysis of heat transfer of the air current simulation based on verified CFD model.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.3
• /
• pp.234-243
• /
• 2012

In this paper, a sound quality indices for the evaluation of vehicle intake and exhaust noise were developed through a correlation analysis of objective measurement data and subjective evaluation data. At first, intake and exhaust orifice noise were measured at the wide-open throttle sweep condition. And then, acoustic transfer function between intake orifice noise and interior noise at the steady state condition was measured. Also, acoustic transfer function for exhaust system was measured as the same method. Simultaneously, subjective evaluation was carried out by the paired comparison and semantic differential method by 27 engineers. Next, the correlation analysis between the psycho-acoustic parameters derived from the measured data and the subjective evaluation was performed. The most critical factor was determined and the corresponding sound quality index for the intake and exhaust noise was obtained from the multiple factor regression method. At last, the effectiveness of the proposed index was investigated.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.11 no.2
• /
• pp.161-169
• /
• 2011

This paper presents a new register transfer level synthesis methodology for efficient SOC system design. The previous register transfer level synthesis systems first translate from a hardware description language to sequential circuits inadequately. Secondly, the systems separate registers and combinational circuits and then optimize only combinational circuits. This paper describes their disadvantages and then proposes a new method to overcome their shortcomings. This paper also shows the effectiveness of the proposed method by using the proposed method at designing the controller of a surveillance system.

• Journal of Power Electronics
• /
• v.17 no.2
• /
• pp.453-463
• /
• 2017

This paper discusses the measurement of frequency response functions for various dc-dc converters. The frequency domain identification procedure is applied to the measured frequency responses. The identified transfer functions are primarily used in developing behavioral models for dc-dc converters. Distributed power systems are based upon such converters in cascade, parallel and several other configurations. The system level analysis of a complete system becomes complex when the identified transfer functions are of high order. Therefore, a certain technique needs to be applied for order reduction of the identified transfer functions. During the process of order reduction, it has to be ensured that the system retains the dynamics of the full order system. The technique used here is based on the Hankel singular values of a system. A systematic procedure is given to retain the maximum energy states for the reduced order model. A dynamic analysis is performed for behavioral models based on full and reduced order frequency responses. The close agreement of results validates the effectiveness of the model order reduction. Stability is the key design objective for any system designer. Therefore, the measured frequency responses at the interface of the source and load are also used to predict stability of the system.

• International Journal of Fluid Machinery and Systems
• /
• v.2 no.1
• /
• pp.55-60
• /
• 2009

The present study investigated temperature and thermal stress distributions in a film cooling system with normal injection cooling flow. 3D-numerical simulations using the FEM commercial code ANSYS were conducted to calculate distributions of temperature and thermal stresses. In the simulations, the surface boundary conditions used the surface heat transfer coefficients and adiabatic wall temperature which were converted from the Sherwood numbers and impermeable wall effectiveness obtained from previous mass transfer experiments. As a result, the temperature gradients, in contrast to the adiabatic wall temperature, were generated by conduction between the hot and cold regions in the film cooling system. The gradient magnitudes were about 10~20K in the y-axis (spanwise) direction and about 50~60K in the x-axis (streamwise) direction. The high thermal stresses resulting from this temperature distribution appeared in the side regions of holes. These locations were similar to those of thermal cracks in actual gas turbines. Thus, this thermal analysis can apply to a thermal design of film cooling holes to prevent or reduce thermal stresses.

• Journal of Aquaculture
• /
• v.9 no.3
• /
• pp.293-300
• /
• 1996

Validities of several gene transfer methods including microinjection, electroporation and lipo-fection with luciferase gene (pRSVL), and effectiveness of mud loach expression vector which contains ARS from mud loach on production of transgenic mud loach were evaluated. Microiniection revealed the $0\~8\%$ of transgene incidence in 2-week-old fish with significant mosaicism. Electroporation and lipofection of mud loach sperm also successfully introduced the transgene into sperm cells, and transferred the foreign DNA into zygote. Gene transfer by electroporation and lipofection showed a range of $0\~28\%$ and $0\~48.1\%$ of transgene incidence, respectively in newly hatched larvae, altough most DNA introduced were gradually degraded with the development of fish. Microinjections of mud loach expression vector caused a significantly reduced survival rate of mud loach embryos with severe teratogenic effects, and ARS/Luc transgene could not be detected in normally developed fish after microinjection.