• Journal of Welding and Joining
• /
• 제19권5호
• /
• pp.486-491
• /
• 2001

The effect of S content in welding wires on spattering characteristics and droplet transfer phenomena was studied. In MAG welding using 80%Ar-$20%CO_2$ shielding gas, spattering characteristics and droplet transfer phenomena were varied with S content of wire. Sulfur addition in wire reduced surface tension of droplet and weld pool, and made arc more stable in MAG welding. With increasing S content, the spattering ratio and the ratio of large size spatter ($d{\geq}1.0mm$) were reduced in short circuit transfer mode. In spray transfer mode, spattering ratio, however was increased when sulfur was added more than 0.020wt.% because surface tension of droplets and weld pool was reduced too much even though arc stability was improved.

• Journal of Welding and Joining
• /
• 제17권1호
• /
• pp.55-61
• /
• 1999

The effect of S content in welding wires on the arc stability was investigated, in the region of short circuit transfer and spray transfer. In the region of short circuit transfer, with increasing S content, average arcing time and average short circuit time were decreased. Therefore, droplet transfer frequency was increased, due to the reduction of arcing time and peak current at the moment of arc-reiginition was decreased, due to the decrease of short circuit time. In the region of spray transfer, the fluctuation degree of arc current and arc voltage became more stable, with increasing S content.

• 한국수정란이식학회:학술대회논문집
• /
• 한국수정란이식학회 2004년도 제4회 발생공학 국제심포지움 및 학술대회
• /
• pp.63-63
• /
• 2004

• 한국사회복지학
• /
• 제63권2호
• /
• pp.133-154
• /
• 2011

본 연구는 자녀와 동거하지 않는 65세 이상 노인을 대상으로 노년기 독립적인 삶의 기대감과 노인의 하향이전의 관계를 실증적으로 검토하여 분석하였다. 분석에 사용된 자료는 "2008년도 전국 노인생활실태 및 복지욕구조사"자료이며, 자료분석은 다중회귀분석을 이용하였다. 분석결과, 노인의 독립적인 삶의 기대감 정도는 노인의 하향이전 정도에 정적(+)인 영향을 주는 것으로 나타났으며, 구체적으로 경제적 신체적 독립적인 삶의 기대감은 노인의 경제적 서비스 하향이전에 정적(+)인 영향을 주는 것으로 나타난 반면, 심리적 독립적인 삶의 기대감은 노인의 서비스 하향이전에는 정적(+)인 영향을 주는 것으로 나타났지만 경제적 하향이전에는 영향을 주지 않는 것으로 나타났다.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2004년도 유체기계 연구개발 발표회 논문집
• /
• pp.140-150
• /
• 2004

In this study, the effect of relative position of the blade for the fixed vane has been investigated on blade surface heat transfer. The experiments were conducted in a low speed stationary annular cascade, and heat transfer of blade was examined for six positions within a pitch. Turbine test section has one stage composed of sixteen guide vanes and blades. The chord length of the tested blade is 150 mm and the mean tip clearance of the blade having flat tip is about $2.5\%$ of the blade chord. For the detailed mass transfer measurements on the blade surfaces, a naphthalene sublimation technique was used. The inlet flow Reynolds number is fixed to $1.5{\times}10^5$. Complex heat transfer characteristics are observed on the blade surface due to various flow characteristics, such as separation bubble, relaminarization, transition to turbulence and leakage vortices. The distributions of velocity and turbulence intensity change significantly with the relative position due to the blockage effect of the blade. This causes the variation of heat transfer patterns on the blade surface. The results show that the flow near the leading edge get highly disturbed and deflected toward the either side of the blade when the blade leading edge is positioned close to the trailing edge of the vane. Therefore, separation bubble disappears on the pressure side and overall heat transfer on the relaminarization region is increased. But, due to reduced tip gap flow at the upstream region, the effect of leakage flow on the upstream region of the blade surface is weakened. Thus, the heat transfer characteristics significantly change with the blade positions.

• Journal of Photoscience
• /
• 제3권3호
• /
• pp.147-151
• /
• 1996

Dynamics of contact ion-pair between 1, 2, 4, 5-tetracyanobenzene anion and cation of biphenyl derivatives was investigated on the picosecond time scale. Solvent effect on the electron transfer was observed and electron transfer rates were examined using Marcus equation which contains distance dependence of the electron transfer rate in the frequency factor, along with the consideration of molecular shape. From the discussion based on disk model for molecular shape, contribution of interring torsional motion of biphenyl to the inner-sphere reorganization energy is strongly suggested, which leads to the physical explanation for the observed solvent effect on the rate of electron transfer.

• Tribology and Lubricants
• /
• 제17권3호
• /
• pp.221-227
• /
• 2001

The effect of silver particles on the sliding behavior of bearing steels was studied experimentally by using a ball-on-disk tribometer. Tests were performed in ambient air, dry air and vacuum. Disks of AISI 52100 were silver-coated by a thermal evaporation method, and the effects of silver particle transfer on friction were analyzed. In order to understand further the mechanism of silver particle transfer and its effect on friction and wear, pre-compressed silver particles were artificially introduced into the friction interface and the results were compared to those of silver-coated specimens. Results showed that the introduced silver particles produced transfer layers and resulted in low friction. It also showed that this low friction is closely related to the characteristic behavior of transfer layers. Shakedown occurred at the friction interface affected the friction and wear.

• 대한기계학회논문집
• /
• 제18권10호
• /
• pp.2779-2786
• /
• 1994

This study presents an experimental investigation of the effect of the wake on mass transfer about a circular cylinder in crossflow. The flat-plate wake was generated by merging two mirror images of turbulent boundary layers that were well developed along the both sides of flat plate with a sharp trailing edge. The velocity field was measured by a hot-wire system and the mass transfer rate by a naphthalene sublimation method. The mixing and developing stages of the wake were addressed to identify flow conditions. The mass transfer effects of different developing stages of the wake was discussed in detail. It is noted that a local maximum appears not at the front stagnation point but at a point a little downstream when the cylinder is located in the nearwake region and much more elevated mass transfer rate is obtained compared to effect of free-stream turbulence.

• 지식경영연구
• /
• 제11권3호
• /
• pp.13-29
• /
• 2010

This study aims to investigate the effect of mentoring functions (career development, role modeling, and psychosocial function) on the motivation to adopt knowledge and the success of knowledge transfer in formal mentoring relations. There are considerable empirical investigation into the antecedents and consequences of mentoring, such as organizational commitment, organizational citizenship behavior, job satisfaction, In this paper, based on the relevant literatures, hypotheses are established and empirically tested that are about the effect of mentoring functions on the motivation to adopt knowledge, and the effect of motivation to adopt knowledge on the success of knowledge transfer. Using a sample of 287 service industry employees, the empirical results shows that career development and role modeling functions ware positively related to motivation to adopt knowledge, but psychosocial function was not significantly related. In addition, the motivation to adopt knowledge was positively related to the success of knowledge transfer. Based on these findings, implication and future direction are discussed.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2000년도 제32회 추계학술대회 정기총회
• /
• pp.59-66
• /
• 2000

An experimental study on the effect of silver particles on the sliding behavior of bearing steels was performed by using a ball-on-disk tribometer. Tests were carried out in ambient air, dry and vacuum. Disks of AISI 52100 were silver-coaled by a thermal evaporation method, and the effects of silver particle transfer on friction were firstly analyzed. In order to understand further the mechanism of silver particles transfer and its effect on friction and wear, pre-compressed silver particles were artificially introduced into the friction interface and the results were compared to those of silver-coated specimens. Results showed that the introduced silver particles produced transfer layers and resulted in low friction. It also showed that this low friction is closely related to the characteristic behavior of transfer layers. Shakedown and rachetting occurred at the friction interface and affected the friction and wear.