• 융합정보논문지
• /
• 제12권5호
• /
• pp.133-138
• /
• 2022

누설자속으로 변압기의 잔류자속을 구하는 기존의 연구에서는 전달함수를 이용하였다. 전달함수는 변압기의 ±의 두 잔류 점을 지나는 순간에 측정한 잔류자속과 동일한 순간에 변압기 밖에서 구한 누설자속으로 구하였다. 본 연구에서는 전달함수를 구하지 않고 동작 최대의 누설자속과 잔류자속에 의한 누설자속의 비를 계산하여 잔류자속을 구하는 방법이 가능함을 확인하였다. 이 방법의 장점은 전류잡음으로 인한 전달함수의 불확정성을 피하는 것이다. 그리고 센서의 잡음을 측정하여 잡음의 드리프트가 측정결과에 미치는 영향을 조사하였다. 잔류 누설 자속밀도를 센서의 드리프트인 80nT와 비교하면 거리 10mm에서는 약 66배, 100mm에서는 5배 이상이었다. 측정거리 100mm는 본 연구에서 얻어진 잔류자속을 구하기 위한 최대 측정 거리였다.

• 대한기관윤리심의기구협의회지
• /
• 제5권1호
• /
• pp.14-20
• /
• 2023

Purpose: To obtain fundamental data on selection tools for an internal audit and develop a new guideline. We scored the indicated points from the internal audit, identified the research progress and problems that occurred, and confirmed the validity of the risk factors involved. Methods: Of the 63 internal audits conducted by Keimyung University Dongsan Hospital from 2014 to 2021, we analyzed 55 clinical trials with an inspection checklist. We excluded 8 that failed to transfer data and refused to comply with the internal audit. The statistical summary of the collected data was verified and interpreted by using frequency analysis and a chi-square test. Result: Of total 55 cases included in the internal audit, sponsor-initiated trial (SIT) was 63.6% (vs. investigator-initiated trial [IIT]), clinical trial for investigational drug was 71.0% (vs. nonclinical or clinical trial for investigational device), domestic multicenter trial was 60.0% (vs. single center or multinational multicenter trial), and trial requisition for MFDS approval was 69.1% (vs. exception for MFDS approval). The 10 areas of the clinical trial inspection checklist (reports, protection of subjects, compliance with protocols, records, management of investigational drug and/or device, delegation of duties, qualification of investigators, management of specimen, contract-agreement and approval of protocols, and preservation of recorded documents) were weighted between 2 to 5 points. The average of the total points was 16.09±13.2 and 20 clinical trials were above the average. As a result of comparing the average of the total points weighted by year, the highest score was in 2020. The 4 factors that play significant roles in determining the internal quality were (1) principal subjects that initiated the clinical trials (p=0.049), (2) type (p=0.003), (3) phase of clinical trials (p=0.024), and (4) number of registered subjects reported at the time of continuing deliberation (p=0.019). Of the 10 areas of the clinical trial inspection checklist, 'record' was the most inappropriate and insufficient. We found more indicated points; the quality of performance declined in IIT, nonclinical trials, and other clinical trials that were not in phase I1-IV4, and the study of more than 30 registered subjects at the time of continuing review. Conclusion: If an institution has an internal audit selection tool that reflects the aforementioned risk factors, it will be possible to effectively manage high-risk studies; thereby, contributing to an efficient internal audit and improving the quality of clinical trials.

• Journal of International Society for Simulation Surgery
• /
• 제1권1호
• /
• pp.27-31
• /
• 2014

In this paper, an overview of segmentation and 3D visualization methods are presented. Commonly, the two kinds of methods are used to visualize organs and vessels into 3D from medical images such as CT(A) and MRI - Direct Volume Rendering (DVR) and Iso-surface Rendering (IR). DVR can be applied directly to a volume. It directly penetrates through the volume while it determines which voxels are visualizedbased on a transfer function. On the other hand, IR requires a series of processes such as segmentation, polygonization and visualization. To extract a region of interest (ROI) from the medical volume image via the segmentation, some regions of an object and a background are required, which are typically obtained from the user. To visualize the extracted regions, the boundary points of the regions should be polygonized. In other words, the boundary surface composed of polygons such as a triangle and a rectangle should be required to visualize the regions into 3D because illumination effects, which makes the object shaded and seen in 3D, cannot be applied directly to the points.

• 한국전산유체공학회지
• /
• 제19권4호
• /
• pp.14-19
• /
• 2014

This study conducts shape optimization of rib turbulator on the internal cooling passage that has triangular cross-section of high pressure turbine nozzle. During optimization, various types of rib turbulator including angled, V-shaped, A-shaped and angled rib with intersecting rib are considered. Each type of rib turbulator is parameterized with attack angle(s), rib height, spacing ratio and bending/intersecting location. For optimization, Design of Experiment (DOE) and Kriging surrogate model are used to utilize computational resource more efficiently and Genetic Algorithm (GA) is used to search the optimum points. As a result, Pareto front of each type of rib turbulator with friction factor that relates to pressure drop in cooling passage and spatially averaged Nusselt number that relates to heat transfer on the wall is drawn and optimum points on the Pareto front are suggested.

• 대한기계학회논문집A
• /
• 제22권2호
• /
• pp.251-257
• /
• 1998

Active mufflers have been mainly applied in the large industrial engine due to considerable expense for implementation, but a necessity of development has been increased by the tightened regulation of exhaust noise and the request of high power. In this study, the active muffler prototype for installing in an automobile is designed and constructed. The active muffler is designed so that the primary noise and the control sound are propagated as a plane wave in the outlet. Therefore, the error microphone could be placed outside the high temperature centers of the tail pipe, and the noise radiating to the outside could be reduced in the whole areas around the outlet. For evaluating the control performance of the prototype, the control experiments of band-pass filtered random signal and the modulation of sinusoidal signal which are generated from the primary noise speaker as practical exhaust sound level are implemented. And to investigate the radiation pattern from the outlet of tail pipe and the noise reduction level of points placed adjacent to the outlet, the sound level of adjacent points of thirty is measured.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2001년도 추계학술대회 논문집
• /
• pp.109-114
• /
• 2001

Photovoltaic systems normally use a maximum power point tracking (MPPT) technique to continuously deliver the highest possible power to the load when variations in the insolation and temperature occur. A simple method of tracking the maximum power points (MPPs) and forcing the boost converter system to operate close to these points is presented through deriving small-signal model and transfer function of boost converter. This paper aims at modeling boost converter including equivalent series resistance of input reservoir capacitor by state-space-averaging method. In the future, properly designed controller for compensation will be constructed for maximum photovoltaic power tracking control.

• 한국태양에너지학회 논문집
• /
• 제29권6호
• /
• pp.1-13
• /
• 2009

Photovoltaic conditioning systems normally use a maximum power point tracking (MPPT) technique to deliver the highest possible power to the load continuously when variations occur in the insolation and temperature. A unique method of tracking the maximum power points (MPPs) and forcing the boost converter system to operate close to these points is presented through deriving small-signal model and transfer function of boost converter considering input capacitor. This paper aims at modeling boost converter including fairly large equivalent series resistance(ESR) of input reservoir capacitor by state-space-averaging method and PWM switch model and compares both methods using Bode plots. In the future, properly designed controller for compensation will be constructed in 3kw real system for maximum photovoltaic power tracking control.

• 한국태양에너지학회 논문집
• /
• 제28권5호
• /
• pp.85-95
• /
• 2008

Photovoltaic conditioning systems normally use a maximum power point tracking (MPPT) technique to deliver the highest possible power to the load continuously when variations occur in the insolation and temperature. A unique method of tracking the maximum power points (MPPs) and forcing the boost converter system to operate close to these points is presented through deriving small-signal model and transfer function of boost converter considering input capacitor. This paper aims at modeling boost converter including fairly large equivalent series resistance(ESR) of input reservoir capacitor by state-space-averaging method and PWM switch model. In the future, properly designed controller for compensation will be constructed in 3kw real system for maximum photovoltaic power tracking control.

• 한국기계가공학회지
• /
• 제17권5호
• /
• pp.37-44
• /
• 2018

In laser material processing for high thermal conductivity, the thermal effect of laser beam shape was examined through computer simulations. In this paper, a circular beam with a focal radius of $500{\mu}m$, an elliptical beam with a major axis of 4 mm and a minor axis of 1 mm, and a rotating beam with a focal radius of $500{\mu}m$ and an angular velocity of 5 rad/sec were compared. Simulation results showed that there was no clear difference in the maximum temperature between the circular focus and the elliptical shape, but the heating and cooling rates were different. The simulation result for a laser beam rotating in a circular pattern with a radius of 5 mm showed an asymmetric temperature rise due to the combination of linear and rotational motion. At points where the rotational and linear speeds combined, the temperature gradually rose and reached the maximum temperature; whereas at points where the rotational and linear speeds were attenuated, the temperature tended to gradually decrease after reaching the maximum temperature. Based on the results of this study, the authors expect to be able to optimize laser material processing by designing patterns of laser beams.

• Steel and Composite Structures
• /
• 제45권1호
• /
• pp.1-21
• /
• 2022

In the structural analysis of steel frames, joints are generally considered as rigid or hinged considering their moment transfer ability. However, the first studies conducted with the beginning of the 20th century showed that the joints do not actually fit these two definitions. In reality, a joint behaves between these two extreme points and is called semi-rigid. Including the actual state of the joint in the structural analysis provides significant economic advantages, so the subject is an intense field of study today. However, it does not find enough application area in practice. For this reason, a large-scale literature published from the first studies on the subject to the present has been examined within the scope of the study. Three important points have been identified in order to examine a joint realistically; modelling the load-displacement relationship, performing the structural analysis and how to design. Joint modelling methods were grouped under 7 main headings as analytical, empirical, mechanical, numerical, informational, hybrid and experimental. In addition to the moment-rotation, other important external load effects like axial force, shear and torsion were considered. Various evaluations were made to expand the practical application area of semi-rigid connections by examining analysis methods and design approaches. Dynamic behaviour was also included in the study, and besides column-beam connections, other important connection types such as beam-beam, column-beam-cross, base connection were also examined in this paper.