• International Journal of Highway Engineering
• /
• v.8 no.1 s.27
• /
• pp.77-87
• /
• 2006

Dynamic stability (DS) in the wheel tracking (WT) test is used as a basic index of rut-resistance for asphalt mixtures. In general, the deeper rut depth is obtained from the weaker mixture, resulting in the lower DS value. On the other hand, the shallower rut depth is obtained from the stronger mixture, resulting in the higher DS. However, it is not always the case when the DS is calculated by the existing method because the DS is simply determined based on the slope at the final stage of the rut depth-cycle curve. Specifically, in the case of the depth-cycle curve showing a steeper slope in the early part but flatter slope in last part, the DS is calculated to be higher than the curve showing a ever-increasing slope throughout the test. As long as the last part of slope is flatter, the deeper final rut depth is evaluated to show a higher DS than the little final rut depth. Therefore, a reasonable method for DS evaluation need to be established. Several new methods were suggested by considering the early, middle and final parts of rut depth to determine a reasonable DS. The results have shown that those new methods have demonstrated a significant improvement in distinguishing similarly performing mixtures. The result also showed that $DS_2$ had better correlation with SD than any other methods , representing the rutting resistance of asphalt mixture very well. The new DS calculation method is relatively simple and easy to follow. More validatin study is required for practical application.

• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.9
• /
• pp.72-80
• /
• 2009

When the magnet wheel rotates over a conducting plate, it generates the traction torque as well as the repulsive force on the conducting plate. Partially-cut traction torque results in the linear force into the tangential direction. To cut the traction torque, the concept of magnetic shield is introduced. The direction change of the linear force is realized varying the shielded area of magnetic field. That is, the tangential direction of non-shielded open area becomes the direction of the linear thrust force. Specially a shape of permanent magnets composing the magnet wheel leads to various pattern of magnetic forces. So, to enlarge the resulting force density and compensate its servo property a few simulations are performed under various conditions such as repeated pattern, pole number, radial width of permanent magnets, including shape of open area. The theoretical model of the magnet wheel is derived using air-gap field analysis of linear induction motor, compared with test result and the sensitivity analysis for its parameter change is performed using common tool; MAXWELL. Using two-axial wheel set-up, the tracking motion is tested for a copper plate with its normal motion constrained and its result is given. In conclusion, it is estimated that the magnet wheel using partial shield can be applied to a noncontact conveyance of the conducting plate.

• Journal of the Korean Geotechnical Society
• /
• v.17 no.4
• /
• pp.191-198
• /
• 2001

국내 도로포장의 주요 파손형태는 주변환경 및 반복 교통하중 조건에 의한 소성변형(rutting), 피로균열, 반사균열, 온도균열 등이 있는데, 포장이 설계수명에 도달하기 이전에 주로 발생하며 이로 인한 도로포장의 유지관리에 막대한 국가예산이 낭비되고 있는 실정이다. 본 연구에서는 토목섬유 아스팔트 포장 시스템을 체계적으로 정립하기 위해 휠트래킹 시험과 균열저항성 시험을 수행하여 토목섬유 아스팔트 포장의 소성변형 및 균열 저항성을 분석하였다. 이러한 실험결과를 통해 아스팔트 포장에서의 토목섬유 보강 효과가 평가되었다.

• Proceedings of the KSME Conference
• /
• 2001.06b
• /
• pp.416-421
• /
• 2001

It was firstly issued that frequently broken of Encoder installed at travelling motor during RTGC operation. Estimated as broken due to excessive vibration of traveling and motor manufacturer claimed it as resonance of motor base. The principal vibration of Encoder was caused by the rotating vibration component of motor and by traveling wheel. The component transmitted from the wheel didn't have great vibration by the resonance with motor and other parts. Therefore, the plans was tried to add the support point to prevent the Encoder shaft vibrated greatly and inhibit the vibration. These showed good results.

• Journal of KSNVE
• /
• v.9 no.3
• /
• pp.613-620
• /
• 1999

Brake judder{or cold judder) caused by the disc thickness variation(DTV) is investigated experimentally, This cold judder is often perceived by steering wheel vibration, brake pedal pulsation, and vehicle body vibration. In this paper, how the DTV profile affects the vibration characteristics of vehicle body is shown by order tracking analysis(OTA) and operational vibration analysis(OVA) The tri-axial vibrations are measured at the knuckle, lower rm, and the body side of the lower arm. Also, measured are the wheel speed and the detail DTV profile. The interpretations of OTA results in three directions of tested vehicle indicate the relative importance in the contribution of the run-out and the DTV to the judder vibration. Also, the OVA results show the prominent vibration amplitude of the lower arm in the direction of the vehicle movement. in which the second order of wheel speed is dominant. These results could be used to diagnose the judder problem and to establish the correction methods.

• International Journal of Highway Engineering
• /
• v.12 no.4
• /
• pp.87-92
• /
• 2010

This study evaluates the laboratory properties of asphalt binder and mixture modified with R-EPDM(Recycling Ethylene Propylene Dien Monometer), which consists of R-EPDM as a main ingredient that is an industrial by-product made by manufacturing waste EPDM below 50 mesh as an additive. Superpave system was used to determine the PG(Performane Grade) and evaluate the property of R-EPDM modified binder. OACs(Optimum Asphalt Contents) of R-EPDM modified asphalt mixtures were determined by Superpave mix design using gyratory compactor and wheel tracking test and moisture susceptibility test were carried out with R-EPDM modified asphalt mixtures at OACs. The results from these tests, rutting-resistance and freezing and thawing resistance by moisture susceptibility of R-EPDM modified asphalt mixtures were superior to one of general asphalt mixtures(AP-5).

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.37 no.2
• /
• pp.497-505
• /
• 2017

TDF (Tire derived fuel) Fly ash is an industrial by-product when scraped tire was used a fuel source at the power plant. TDF Fly ash has been classified as domestic waste at the workplace so far and has not been appropriately utilized. We conducted a fundamental physical property test of asphalt mixture to investigate the possibility of using TDF Fly ash as a mineral filler of asphalt mixture for exploring new usage strategies. TDF Fly ash meets KS F 3501 asphalt mixture mineral filler criteria. And the optimal asphalt binder amount was determined to be 4.5% by Marshall design. Mineral filler content was determined at 3% and analyzed by comparing using mineral filler as stone powder. The basic physical property test of the asphalt mixture was evaluated to the provision indicated in "Production and Construction Guidelines for Asphalt Mixture" published by the Ministry of Land, Infrastructure and Transport. In the test, Marshall stability test, dynamic immersion test, tensile strength ratio test, wheel tracking test were carried out. As a result of the experiment, Marshall stability and dynamic stability satisfied the standards, and confirmed the stability and Dynamic immersion and tensile strength ratio test that TDF Fly ash is more effective for scaling and moisture resistance than stone dust. Therefore, in this research, it is expected that multilateral utilization of TDF Fly ash, and a positive effect can be also expected.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.539-542
• /
• 2003

Recently, the polymer insulators which are being used for high voltage applications have some advantages such as light weight, small size, vandalism resistance, hydrophobicity and easy making process. During outdoor service of polymer insulators, the surface of the insulating material is frequently subjected to moisture and contamination which lead to the well known phenomenon of dry band arcing. Their tracking resistance, erosion resistance, end sealing and shed design are very important because dry band arcing causes degradation of polymer surface. The shape design of porcelain insulator is formalized but design standard for polymer insulator is no standardized up to now, much research is necessary in real condition. In this paper, the aging property of polymer insulator with shed shape(regular, alternative type) is analyzed through numerical analysis, CEA(canadian electricity association) tracking wheel test and IEC 61109 Annex C.

• International Journal of Highway Engineering
• /
• v.6 no.2 s.20
• /
• pp.1-13
• /
• 2004

This study dealt with size effect of specimen in measuring deformation strength and estimating rut resistance of asphalt concretes under static loading using Kim test. Two aggregates, a normal asphalt (pen 60-80) and 6 polymer-modified asphalt (PMA) binders were used for preparation of 14 dense-graded mixtures. Mixtures were prepared based on optimum asphalt content by Marshall compactor (S= 10cm) and gyratory compactor (S= 15cm) for Kim test and for wheel tracking test. In statistical analysis by general linear model (GLM) procedure of SAS, the diameter of specimen was found not to be a significant factor that affect the Kim test result. Therefore, it was found that either loom-diameter or 15cm-diameter of specimen gave no significant difference in deformation strength ($K_D$) values in Kim test for any aggregate mixture. However, the thickness of specimen was found to be a significant factor in determining $K_D$. It is estimated that $K_D$ is a function of y, vertical deformation, and y has something to do with thickness of specimen. Therefore, it is suggested that the thickness of specimen should not be higher than 6.6cm, and the correction factor depending on the thickness value should be developed in the future study.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.2 no.2 s.5
• /
• pp.61-72
• /
• 2002

The optimum fiber and asphalt binder contents were decided on the base of the Mashall mix design method. To compare the mechanical characteristics between the conventional(dense-graded 20) and the fiber-reinforced mixtures, indirect tension tests were conducted under three temperatures(5, 20, 60$^{\circ}C$). In particular, the wheel tracking tests were performed to evaluate the rutting resistances of the mixtures. Test results showed that the indirect tensile strength of fiber-reinforced asphalt concrete was higher than that of conventional one. The toughness of fiber-reinforced mixture was 1.27 to 1.97 times higher than that of conventional one, depending upon the temperature. In addition, the results of wheel tracking tests and the retained indirect splitting tension tests conducted at $60^{\circ}C$ revealed that the resistance to permanent deformation of fiber-reinforced mixture was stronger than that of the conventional one.