• Journal of Biomedical Engineering Research
• /
• v.31 no.5
• /
• pp.401-406
• /
• 2010

Recently, many implantable medical devices have been developed and manufactured in many countries. In these devices, generally, energy is supplied by a transcutaneous method to avoid the skin penetration due to the power wires. As the most transcutaneous power transmission methods, the electromagnetic coupling between two coils and resonance at a specific frequency has been used widely. However, in case of a transcutaneous power transmitter with a fixed switching frequency to drive an electromagnetic coil, inefficient power transmission and thermal damage by the undesirable current variation may occur, because the electromagnetic coupling state between a primary coil and a secondary coil is very sensitive to skin thickness of each applied position and by person. In order to overcome these defects, a transcutaneous power transmitter of which operating frequency can be automatically tracked into the resonance frequency at each environment has been designed and implemented. Through the results of experiments for different coil surroundings, we have been demonstrated that the implemented transcutaneous power transmitter can track automatically into a varied resonance frequency according to arbitrary skin thickness change.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.3 no.3
• /
• pp.263-272
• /
• 1998

This paper presents the new control strategy that can minimizes the torque ripple by considering the magnetic nonlinearity and phase torque averlapping intervals, and describes the whole SRM drive system using proposed control method implemented by DSP(Digital Signal Processor). To do this, inductance and torque are, at first, measured according to the variation of rotor position angle while current is kept constant at predetermined several values. From these measured values, the entire inductance and torque for any current and rotor position are inferred by using neural network. And the waveform of the reference phase torque is determined for the torque ripple to be minimized considering the torque overlap between phases. The controller is designed for the actual torque obtained by the inferred torque look-up table using measured current and rotor position angle to track the predetermined reference phase torque by delta modulation technique. To perform a real time processing and ensure the reliability of the controller, DSP is implemented.

• Journal of Drive and Control
• /
• v.14 no.2
• /
• pp.16-22
• /
• 2017

This paper presents the algorithm of an adaptive model-free-control-based steering control for multi-axle all-terrain cranes for which the recursive least squares with forgetting are applied. To optimally control the actual system in the real world, the linear or nonlinear mathematical model of the system should be given for the determination of the optimal control inputs; however, it is difficult to derive the mathematical model due to the actual system's complexity and nonlinearity. To address this problem, the proposed adaptive model-free controller is used to control the steering angle of a multi-axle crane. The proposed model-free control algorithm uses only the input and output signals of the system to determine the optimal inputs. The recursive least-squares algorithm identifies first-order systems. The uncertainty between the identified system and the actual system was estimated based on the disturbance observer. The proposed control algorithm was used for the steering control of a multi-axle crane, where only the steering input and the desired yaw rate were employed, to track the reference path. The controller and performance evaluations were constructed and conducted in the Matlab/Simulink environment. The evaluation results show that the proposed adaptive model-free-control-based steering-control algorithm produces a sound path-tracking performance.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.13 no.6
• /
• pp.403-410
• /
• 2008

This paper suggests a standstill estimator to accurately identify induction motor (IM) parameters necessary for the vector control. A mathematical model that faithfully represents the general skin effect is introduced. Then, two exciting signals with a different frequency are sequentially injected to track the parameters based on the skin effect of the rotor bar. Little knowledge of the unknown motor allows the proposed methodology to employ a closed-loop control of an injected current, rather than open-loop voltage injection approaches. Subsequently, this control scheme proactively prevents electrical accidents resulting from an inadequate open-loop voltage injection. We develop a specialized offline commissioning test to compensate the phase delay resulting from the drive, which significantly affects the precision of the IM parameters. The effectiveness of the identification technique is validated by means of experiments performed on the three different IMs.

• Journal of the Korean Institute of Educational Facilities
• /
• v.10 no.5
• /
• pp.5-14
• /
• 2003

The purpose of this survey study is to analyse the playground dimension of elementary school. To complete this mission, it is necessary to drive out elementary school have a lower dimension standard of playground through literal survey. Then, questionnaire and observation survey have been performed to teachers majored in physical education and these are focused on playground dimensions. The field survey study will provide the basic data for calculating proper playground dimensions and design source for planning space program of the school. The result of this survey study are as follows ; First, The Area of 'Gyo-ghi' is decreasing, and the land area of being used for 'Gyo-sa' is increasing. So the area of playground is decreasing. Second, The respondents require a playground size enough to contain 100m running track for testing the physical ability of students. But it is not possible to do so in current domestic condition, it is necessary to revise of the standard of physical test or enact a new one. Third, to solve the problems deviating from the playground size, the respondent suggests that set up a new gym or variable-size playgrounds rather than a large one Fourth, because playground has so much functions as rest, playing, walking and jogging etc besides physical education, it is necessary to consider the spaces for rest and play, when plan a tower-type school or small school.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.44 no.4 s.316
• /
• pp.67-73
• /
• 2007

An optical pick up generally has coupled dynamics between focusing and tracking servos. The coupled dynamics reduces tracking performance of optical disk drives. A conventional control method is holding the previous tracking control command in the presence of surface defect. The method has a long settling time. If the defective area is getting larger, objective lens will get away from the following track. In order to overcome this problem, this paper proposed a new control method for optical disk drives based on a prediction of tracking error and focusing error. We present how to compensate the coupled dynamics so that reduced setting time is achieved. It is verified by experiments that the proposed method brings an improved performance in the presence of surface defect as well as in the normal operating condition.

• Journal of Drive and Control
• /
• v.13 no.1
• /
• pp.1-9
• /
• 2016

Nowadays automatic transmission equipped vehicles prevail in construction and agricultural equipment due to their convenience in driving and operation. Though domestic vehicle manufacturers install imported electronic controlled transmissions at present, overseas products will be replaced by domestic ones in the near future owing to development efforts over the past 10 years. For passenger cars, there are many kinds of shift control algorithms that enhance the shift quality such as feedback and learning control. However, since shift control technologies for heavy duty vehicles are not highly developed, it is possible to improve the shift quality with an organized control method. A feedback control algorithm for neutral-into-gear shift, which is enabled during the inertia phase for the master clutch slip speed to track the slip speed reference, is proposed based on the power transmission structure of TH100. The performance of the feedback shift control is verified by a vehicle test which is implemented with firmware embedded TCU. As the master clutch engages along the predetermined speed trajectory, it can be concluded that the shift quality can be managed by a shift time control parameter. By extending the proposed feedback algorithm for neutral-into-gear shift to gear change and shuttle shift, it is expected that the quality of the shift can be improved.

• Asia-pacific Journal of Multimedia Services Convergent with Art, Humanities, and Sociology
• /
• v.9 no.5
• /
• pp.865-872
• /
• 2019

In this paper, we describe the Solar Car, Woongbi, which was created to participate in the World Solar Challenge(WSC) at the team NeulHaeRang of Korea National University of Transportation. The WSC is the world's largest solar car racing competition and has a separate automobile regulation and must be manufactured to meet the regulations. Therefore, the key point of the solar car design is to optimize the energy efficiency based on the regulations. The solar car's drive system consists of a solar array to convert solar energy into electric energy, a maximum power point tracker (MPPT) controller to track the converted electric energy to maximum output power, a battery to store the produced electric energy, a BLDC (Brushless DC) motor for driving the vehicle by converting energy into mechanical energy, and a motor controller for controlling the BLDC. The optimal design methods for solar energy conversion and electric driving system of battery, motor are presented in this paper.

• Journal of IKEEE
• /
• v.26 no.4
• /
• pp.602-613
• /
• 2022

This paper proposes an algorithm for correcting indirect situations resulting from the wheelchair moving the stairs with wheel-type caterpillar and seat position variable. For analyzing the Yawing movement model, the change of Yaw value was estimated using Roll, Pitch, and Yaw in the driving environment, and it was used as a control variable and the information of the wheel drive controller. The verification confirmed the correction of about 10° of Yawing movement within about 7 seconds. It was confirmed that the angular velocity was reduced by 47.5% in seat position change.

• Journal of Korean Society of Forest Science
• /
• v.88 no.2
• /
• pp.255-265
• /
• 1999

This study deals with forest soil characteristics and their effects on the trafficability of logging vehicles. The study area is the national experimental forest located in Kwangnung. This site has 20m length and is equally divided by 5 surveying ranges with 4m width, on which a tractor(FIATAGRI) attached with logging boogie can drive in 4 driving types, namely 1time-return unload, 1time-return with load of 780-790kg weight of 3 logs, 5 and 10times-return with same load. After one driving type on all surveying ranges, the soil hardness is surveyed 5 times with 3 several type tools, SHM-1 type, lang penetrometer(L-PNTM), and clegg impact soil tester(CIST). A disturbed degree of cover vegetation and sliding conditions of vehicle are also observed. As results, the soil type of the test site was SC by USCS and dry brown forest soil. The cover vegetation is gotten trambled under driving after 3-5 times-return, shrubs leaves are fully fallen and their bark are peeled, and after 10 times-return the cover vegetations were nearly disappeared. The test vehicle has neither slided nor was overthrown. The wheel tracks in the 1-3 ranges, of which unit weight(gd, gt) is high and soil moisture content(MC) is low, were only 1-2cm deep, but those in the 4-5 ranges, of which the gd, gt is low and the MC is high, were 5-7cm deep. In the soil hardness test, which was established in 5 test ranges by types of driving, the more driving times, the higher the hardness. The soil hardness surveyed by L-PNTM has changed slowly and that surveyed by SHM-1 type has risen sharply. In the ranges with higher specific gravity(Gs), higher unit weight, lower MC and higher liquid limit(LL) and plasticity index(PI) was the soil hardness high and the trafficability was good. In the ranges with opposite conditions, also in the ranges of the lower soil hardness, the trafficability must be not good, because the wheel track may be deep. The results from CIST attached with 4kg hammer was not better than expected. So it is recommended to use CIST with 2.5kg or 0.5kg hammer.