• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.6
• /
• pp.691-698
• /
• 2014

This paper describes the manufacturing processes for a flexbeam and torque tube made of composite materials, along with the procedures for testing their basic properties. A flexbeam and torque tube can be considered to be key structural components of a bearingless rotor hub system. A hinge offset effect can be realized by a large elastic deformation and twist of the flexbeam, and the blade pitch control forces are transferred by the rotation of the torque tube. The basic property tests included bending and twist tests to determine the flap stiffness, lag stiffness, and torsion stiffness of the flexbeam, torque tube, and blade, and these tests were performed prior to starting the whirl tower test. In addition, the estimated results were compared with experimental data, and the calculations were found to be a good match for the analysis results and had a similar tendency. Through these results, we could confirm that a flexbeam and torque tube made of composite materials satisfied the structural stiffness requirements.

• Journal of the Korean Society of Safety
• /
• v.21 no.4 s.76
• /
• pp.73-84
• /
• 2006

Standard safety management cost system was established in 1988 as a decree Number of 88-13, first time. And then, it has been revised fourteen times, up to now. A lot of practical investigations have been made for the revision but many problems at sites are continued to be put out so that it should be revised. This study is to find out hazard level of each work kinds through questionnaire and interview and investigate analyze the status which standard safety management costs have been used. Also, this study is to show reasonable rates of standard safety management costs in construction industry and to set up countermeasures against those problem after reviewing its status in korea with in Japan and Europe. Budget and actually performed amount of safety management costs in this study are investigated. costs for temporary work which is clarified in Japan is collected in order to compare domestic cost rate with Japanese one related to the total project amount. This study is to investigate eleven project kinds of domestic system, first, and to investigate eleven items of apartment bldg, office, civil work such as bridge, tunnel, dam, plant etc, secondly. Additionally, three items of gymnasium, railway, particular steel tower are investigated in this study. Also this study is to investigate and analyze performed costs of presently processing worker finished work so that it shows a new reasonable rate against standard safety management costs in construction industry, in order to make basical data and material to be systemized.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.55 no.5
• /
• pp.17-23
• /
• 2013

Six-valent chromium ($Cr^{6+}$) is a highly toxic pollutant, supplied in a variety of industrial activities such as leather tanning, cooling tower blowdown, and plating. Herein, we investigated the removal of $Cr^{6+}$ from aqueous phase using low-cost adsorbents. Steel slag, montmorillonite, illite, kaolinite, red mud, and acid treated red mud with 0.5, 1.0, and 2.0 M HCl were used as adsorbent for the removal of $Cr^{6+}$ and the results showed that acid treated red mud with 2.0 M HCl (ATRM-2.0 M) had higher adsorption capacity of $Cr^{6+}$ than other adsorbents used. Accordingly, $Cr^{6+}$ removal by ATRM-2.0 M were studied in a batch system with respect to changes in initial concentration of $Cr^{6+}$, initial solution pH, adsorbent dose, adsorbent mixture, and seawater. Equilibrium sorption data were described well by Freundlich isotherm model. The influence of initial solution pH on $Cr^{6+}$ adsorption was insignificant. The use of the ATRM-2.0 M alone was more effective than mixing it with other adsorbents including red mud, zeolite, oyster shell, lime stone, and montmorillonite for the removal of $Cr^{6+}$. The $Cr^{6+}$ removal of the ATRM-2.0 M was slightly less in seawater than deionized water, resulting from the presence of anions in seawater competing for the favorable adsorption site on the surface of ATRM-2.0 M. It was concluded that the ATRM-2.0 M can be used as a potential adsorbent for the removal of $Cr^{6+}$ from the aqueous solutions.

• Wind and Structures
• /
• v.21 no.6
• /
• pp.693-707
• /
• 2015

The efficiency of wind turbines (WT) is primarily reflected in their ability to generate electricity at any time. Downtimes of WTs due to "conventional" inspections are cost-intensive and undesirable for investors. For this reason, there is a need for structural health monitoring (SHM) systems, to enable service and maintenance on demand and to increase the inspection intervals. In general, monitoring increases the cost effectiveness of WTs. This publication concentrates on the application of two vibration-based SHM algorithms for stability and structural change monitoring of offshore WTs. Only data driven, output-only algorithms based on stochastic subspace identification (SSI) in time domain are considered. The centerpiece of this paper deals with the rough mathematical description of the dynamic behavior of offshore WTs and with the basic presentation of stochastic subspace-based algorithms and their application to these structures. Due to the early stage of the industrial application of SHM on offshore WT on the one side and the required confidentiality to the plant manufacturer and operator on the other side, up to now it is not possible to analyze different isolated structural damages resp. changes in a systematic manner, directly by means of in-situ measurement and to make these "acknowledgements" publicly available. For this reason, the sensitivity of the methods for monitoring purposes are demonstrated through their application on long time measurements from a 1:10 large scale test rig of an offshore WT under different conditions: undamaged, different levels of loosened bolt connections between tower parts, different levels of fouling, scouring and structure inclination. The limitation and further requirements for the approaches and their applicability on real foundations are discussed along the paper.

• The Journal of Industrial Distribution & Business
• /
• v.8 no.6
• /
• pp.61-73
• /
• 2017

Purpose - Aviation control, navigation, and aircraft control in the air transportation area are very specialized. Each part is in progress for safety, efficiency, automation, and further. On the other hand co-work among each part including knowledge sharing has been inattentive for many reasons. The purpose of this research is to show how practicians and professionals in the air transportation area perceive the issue of knowledge sharing and to recall the necessity of knowledge sharing in the area. And we try to find ways to activate the knowledge sharing in the area. Research design, data, methodology - For the research, we inquired into whether practicians and professionals think knowledge sharing can effect safe aviation positively or not and what steps are necessary to activate knowledge sharing in the area. We adopted survey method using questionnaires for current practicians and interview for specialists. The survey and interview results were analyzed using regression analysis and AHP method. The interview for specialists and analyzing the results using AHP was to investigate what are the precedence factors to activate the knowledge sharing. Results - First, practicians perceive that knowledge sharing will affect aviation safe positively. Second objective knowledges such as, tower air traffic control procedure of aviation control area, flight principle and structure of aircraft control area, instrument landing system of navigation area, for knowledge sharing of each area were identified. Also the precedence factors such as, knowledge absorbability of personal factor, personal expectation of result of expectation factor, leadership of management of Structure factor, method of knowledge spread of application factor for knowledge sharing were found. Conclusions - Knowledge sharing for practicians and professionals in the aviation area is very important especially from the perspective of safety. However, for various many reasons including the environment of each special area that focusing on their own area, knowledge sharing has not been emphasized. We found that practicians in the area feel that knowledge sharing is necessary and helpful. For it, each practician's active participation is the most important and many ways such as chatting room to share knowledge are to be developed. And the organization culture should be changed to encourage knowledge sharing.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.10 no.4
• /
• pp.9-16
• /
• 2010

In the health monitoring of civil engineering structures, the optimal sensor placement has a major influence on the quality of the results. This paper considers the problem of locating sensors with the aim of maximizing the data information so that structural parameters or damage of structures can be assessed. An proposed technique using a genetic algorithm is introduced to find the optimal placement of sensors. The sensitivity on modal vectors by structural parameters and the orthogonality of modal vectors have been taken as the fitness function of the genetic algorithm. A simple tower structure is used for example analyses to investigate the feasibility and applicability of the proposed approach. The example analyses show the way how the modal sensitivity and the modal orthogonality in the fitness function have influence on the optimal sensor placement. It is shown that the present method using the proposed fitness function can provide the reliable results.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.27 no.5
• /
• pp.451-458
• /
• 2014

This study is a practical research for setting a process of making references of design decision and guidlines of limitation in the movement from the design development to the construction design by StrAuto. StrAuto, as a parametric modeling and optimization tool for building structure, enables a quantity of design cases to be analyzed automatically by changing parameters of sturctural properties. So the designer using StrAuto can check a lot of analysis data crossing thousands of cases, see which case is out of acceptable range, and make a decision for design and optimization. In this thesis, the application of StrAuto optimization process to the residence tower UIC project shows the practical applicability in the construction design and value engineering. StrAuto optimized ideally volume of core walls by 31.3% and lead the final revised model applied to the construction design to reduce volume by 18.1%. The significance of this research is the implementation of process that the designer can quickly review a number of cases and get a direction for construction design and optimization after design development.

• Journal of Environmental Science International
• /
• v.7 no.3
• /
• pp.375-382
• /
• 1998

The characteristics of the basic statistics and steadiness of wind and the monthly normality test of surface wind distribution are investigated by using the observed wind data compiled from 10m meteorological observation tower at Seocheon district, where is located In the western coastal region of Korea. during the period from Feb. 7, 1996 to Feb. 7 1997 The northerly is appeared to be even in August and Sepember due to the influences of loccal circulation such as land and sea breeze. The correlation coefacients between two wind components are seemed to be positive during the in the period of from June to September and negative from October to April, respectively The constancy of wand Is high In shifts to lower values Increasing sampling time. It is found from monthly normality test based on the skewness and the excess of kurtosis coefficients that the distribution of zonal wind component is normal In spring and meridional one Is normal in late summer and early autumn.

• Journal of Broadcast Engineering
• /
• v.25 no.1
• /
• pp.13-24
• /
• 2020

There are about nine million power line poles and 1.3 million kilometers of the power line for electric power distribution in Korea. Maintenance of such a large number of electric power facilities requires a lot of manpower and time. Recently, various fault diagnosis techniques using artificial intelligence have been studied. Therefore, in this paper, proposes a power line deflection detect system using artificial intelligence and computer vision technology in images taken by vision system. The proposed system proceeds as follows. (i) Detection of transmission tower using object detection system (ii) Histogram equalization technique to solve the degradation in image quality problem of video data (iii) In general, since the distance between two transmission towers is long, a panoramic video stitching process is performed to grasp the entire power line (iv) Detecting deflection using computer vision technology after applying power line detection algorithm This paper explain and experiment about each process.

• Journal of the Korean Institute of Educational Facilities
• /
• v.10 no.5
• /
• pp.5-14
• /
• 2003

The purpose of this survey study is to analyse the playground dimension of elementary school. To complete this mission, it is necessary to drive out elementary school have a lower dimension standard of playground through literal survey. Then, questionnaire and observation survey have been performed to teachers majored in physical education and these are focused on playground dimensions. The field survey study will provide the basic data for calculating proper playground dimensions and design source for planning space program of the school. The result of this survey study are as follows ; First, The Area of 'Gyo-ghi' is decreasing, and the land area of being used for 'Gyo-sa' is increasing. So the area of playground is decreasing. Second, The respondents require a playground size enough to contain 100m running track for testing the physical ability of students. But it is not possible to do so in current domestic condition, it is necessary to revise of the standard of physical test or enact a new one. Third, to solve the problems deviating from the playground size, the respondent suggests that set up a new gym or variable-size playgrounds rather than a large one Fourth, because playground has so much functions as rest, playing, walking and jogging etc besides physical education, it is necessary to consider the spaces for rest and play, when plan a tower-type school or small school.