• Journal of the Optical Society of Korea
• /
• v.14 no.3
• /
• pp.215-220
• /
• 2010

Aerosol observation with Raman LIDAR in NIES (National Institute for Environmental Studies, Japan) LIDAR network was conducted from 17 April to 12 June 2008 over Beijing, China. The aerosol optical properties derived from Raman LIDAR were compared with the retrieved data from sun photometer and sky radiometer observations in the Aerosol Robotic Network (AERONET). The comparison provided the complete knowledge of aerosol optical and physical properties in Beijing, especially in pollution and Asian dust events. The averaged aerosol optical depth (AOD) at 675 nm was 0.81 and the Angstrom exponent between 440 nm and 675 nm was 0.99 during experiment. The LIDAR derived AOD at 532 nm in the planetary boundary layer (PBL) was 0.48, which implied that half of the total AOD was contributed by the aerosol in PBL. The corresponding averaged LIDAR ratio and total depolarization ratio (TDR) were 48.5sr and 8.1%. The negative correlation between LIDAR ratio and TDR indicated the LIDAR ratio decreased with aerosol size because of the high TDR associated with nonspherical and large aerosols. The typical volume size distribution of the aerosol clearly demonstrated that the coarse mode radius located near 3 ${\mu}m$ in dust case, a bi-mode with fine particle centered at 0.2 ${\mu}m$ and coarse particle at 2 ${\mu}m$ was the characteristic size distribution in the pollution and clean cases. The different size distributions of aerosol resulted in its different optical properties. The retrieved LIDAR ratio and TDR were 41.1sr and 19.5% for a dust event, 53.8sr and 6.6% for a pollution event as well as 57.3sr and 7.2% for a clean event. In conjunction with the observed surface wind field near the LIDAR site, most of the pollution aerosols were produced locally or transported from the southeast of Beijing, whereas the dust aerosols associated with the clean air mass were transported by the northwesterly or southwesterly winds.

• Journal of Environmental Science International
• /
• v.18 no.1
• /
• pp.41-47
• /
• 2009

In building demolition work, major dust-generating activities are blasting concrete and rock. The aim of this study was to find the characteristic of particle size of dusts which were generated during building demolition work using explosion. The DustMate of the Turnkey-Instruments Ltd. was used for particulate size-selective sampling of the four sites. TSP(Total Suspended Particle), PM10(Particle Matter $10{\mu}m$), PM2.5(Particle Matter $2.5{\mu}m$), and PM1.0(Particle Matter $1.0{\mu}m$) were measured during building demolition work using explosion. The large particulate (higher than the diameter $10{\mu}m$) showed to be higher than 50%. The particulate ranged from $10{\mu}m\;to\;2.5{\mu}m$ showed about 30-40%. PM2.5 was not scarcely detected in the samples collected for building demolition work using explosion. We conclude that the dust generated during building demolition work using explosion has not most respirable particulate.

• Journal of Environmental Health Sciences
• /
• v.36 no.4
• /
• pp.271-278
• /
• 2010

The appearance of Asian Dust (AD) originating from China and Mongolia during spring each year is a meteorological phenomenon periodically observed in extensive regions of East Asia. According to a previous epidemiological study, AD has adverse effects on both human beings and ecosystems. In this study, we collected total suspension particles (TSP) in the AD period and Non-AD (NAD) period. We extracted organic components from TSP using dichloromethane (DCM), and the polyaromatic hydrocarbons (PAHs) were analyzed. The DCM extracts contained PAHs such as benzo(b)fluoranthene, benzo[g,h,i]perylene, benzo(k)fluoranthene, benzo(a)pyrene, and pyrene. No significant difference was observed in cytotoxicity of the DCM extracts from AD versus NAD when tested on the human bronchial epithelial cells, BEAS-2B. e also examined the toxic mechanisms of AD extracts in cultured BEAS-2B cells and RAW264.7 cells, and in BEAS-2B cells observed increased levels of reactive oxygen species (ROS), decreased glutathione (GSH), and induced caspase-3 activity. Increased expression of oxidative stress-related and inflammation- related genes were also observed in BEAS-2B cells, while nitric oxide (NO) levels were increased in RAW264.7 cells. Taken together, the results suggest that in these cultured cells, AD may induce cytotoxicity through oxidative stress and pro-inflammatory signals.

• Journal of Korean Society for Atmospheric Environment
• /
• v.6 no.1
• /
• pp.1-10
• /
• 1990

The purpose of the study was to analyze air quality in underground shopping centers using pattern recognition methods. In order to perform this, the concentraion of air pollutants such as $CO, NO_2, NO_x, SO_2$, and particulate matters was measured at the 11 different shopping centers in Seoul metropolitan area and the total of 47 samples were obtained at random based on the size of shopping centers. To introduce a new concept of the "average concentration" for the indoor air quality analyses, the various multivariate statistical analyses have been studied. Thus, a cluster analysis was applied to separate the samples into pseudo-patterns and a disjoint principal component analysis was used to generate homogeneous patterns after removing outliers from the pseudo-patterns. The 6 homogeneous patterns were then obtained as follows:the first pattern was a group of clean sites;the second a group of sites having high dust concentration;the third a group of sites having high dust and $NO_x$ concentration;the fourth a group of sites having low dust and $SO_2$ concentraion and high CO concentration;the fifth a group of sites having high $NO_2 and SO_2$ concentration;and the final a group of miscellaneous sites. Thus, the average concentration could be estimated for each pattern.h pattern.

• Atmosphere
• /
• v.17 no.3
• /
• pp.299-314
• /
• 2007

The purpose of this study is to summarize tropical cyclone activity in 2006. Twenty three tropical cyclones of tropical storm (TS) intensity or higher formed in the western North Pacific and the South China Sea in 2006. The total number is less than the thirty-year (1971~2000) average frequency of 26.7. Out of twenty three tropical cyclones, fifteen cyclones reached typhoon (TY) intensity, while the rest eight cyclones only reached severe tropical storm (STS) and tropical storm (TS) intensity - three STS and five TS storms. The tropical cyclone season in 2006 began in May with the formation of CHANCHU (0601). The convective activity was slightly inactive around the Philippines from late June to early August. In addition, subtropical high was more enhanced than normal over the south of Japan from May to early August. Consequently, most tropical cyclones formed over the sea east of the Philippines after late June, and many of them moved westwards to China. CHANCHU (0601), BILIS (0604), KAEMI (0605), PRAPIROON (0606) and SAOMI (0608) brought damage to China, the Philippines, and Vietnam. On the other hand, EWINIAR (0603) moved northwards and hit the Republic of Korea, causing damage to the country. From late August to early September, convective activity was temporarily inactive over the sea east of the Philippines. However, it turned active again after late September. Subtropical high was weak over the south of Japan after late August. Therefore, most tropical cyclones formed over the sea east of the Philippines and moved northwards. WUKONG (0610) and SHANSHAN (0613) hit Japan to bring damage to the country. On the other hand, XANGSANE (0615) and CIMARON (0619) moved westwards in the South China Sea, causing damage to the Philippines, Thailand, and Vietnam. Another special feature in 2006 tropical cyclone activity is that IOKE (0612) formed in the central North Pacific crossed 180 degree longitude and moved into the western North Pacific. It has been four years since HUKO (0224) in 2002.

• Journal of Preventive Medicine and Public Health
• /
• v.27 no.2 s.46
• /
• pp.274-285
• /
• 1994

The effects of resin on the respiratory health have been investigated in 309 workers from four iron and steel foundries and the results compared with those from 122 workers who were not significantly exposed to resin gas and silica dust at the same industries. Phenol-formaldehyde resin was used in the core making and molding processes and workers were exposed to their decomposition products as well as to silica dust containing particulates. The subjects were grouped according to formaldehyde, dust and other gas exposures, and smoking habits were considered also in thi analysis. Standardized respiratory symptom questionnaire was administered by trained interviewers. Chest radiograph, pulmonary funtion tests, and methacholine challenge tests were done. Environmental measurements at the breathing zone were carried out to determine levels of formaldehyde, respiable dust and total dust. Foundry workers had a higher prevalence of symptoms of chronic bronchitis with chronic phlegm and chronic cough when exposed to dust. Exposure to gas was significantly associated with lowered $FEV_1$ and obstructive pulmonary function changes. Exposure to formaldehyde and phenol gas was associated with wheezing symptom among workers, but $FEV_1$ changes after methacholine challenge were not significantly different among different exposure groups. When asthma was defined as the presence of bronchial hyperreactivity with more than 20% decrease in $FEV_1$ after methacholine challenge, 17 workers out of 222 tested had asthma. Fewer asthmatic welters were found among groups exposed to formaldehyde, gas and dust, which indicates a healthy worker effects ill a cross-sectional study. The concentration of formaldehyde gas ranged from 0.24 to 0.43 ppm among studied foundries. The authors conclude that formaldehyde and phenol gas from combusted resin is probably the cause of asthmatic symptoms and also a selection force of those with higher bronchial reactivity away from exposures.

• Journal of the Society of Disaster Information
• /
• v.10 no.1
• /
• pp.71-83
• /
• 2014

This study carried out an experiment in order to compare thermal characteristics after collecting dust generated in the process of disposing of waste tire, plywood flour in the process of manufacturing plywood, salicylic acid dust in the process of manufacturing functional soap, and dust in the process of manufacturing wheat powder, which has potential fire and explosion hazard. According to the results of experiment, the analysis showed that all samples subject to the experiment were in the condition where heat flux decreased and temperature decreased as the quantity of added talc was increased. This shows that decomposition rate decreased, and hazard decreased. However, in all of samples subject to the experiment, as heating rate increased, endothermic onset temperature moved to the low-temperature part, and the amount of absorbed heat was largely increased. This showed that the decomposition hazard of sample increased as heating rate increased, according to the analysis. Besides, TGA experiment results showed that thermal stability was secured because total weight loss decreased as the amount of talc was increased for all samples subject to the experiment regarding the ratio of weight loss. It is expected that the continuous research and supplementation of dust explosion mechanism in the future will contribute to the establishment of measures for the effective dust explosion prevention.

• Journal of Korean Society of Environmental Engineers
• /
• v.34 no.3
• /
• pp.168-176
• /
• 2012

A total of 48 dust samples were collected from large shopping mall parking lots in Daegu metropolitan city in March 2011. Samples were sieved through a 100 ${\mu}m$ mesh and the concentration of 14 elements have been determined using by ICP after acid extraction. Results showed that Ca, Fe, K, Mg, Mn, Na and V were affected by natural sources while Cd, Cr, Cu, Ni, Pb and Zn were affected by anthropogenic sources. The measured values were remarkably higher in components from natural sources than in components from anthropogenic sources. Anthropogenic trace element concentrations of ground roof dust were higher than those of ground and underground indoor dust. A large percentage of trace elements came from natural sources rather than anthropogenic sources. The percentage composition of chemicals of ground roof dust were higher than those of ground and underground indoor dust. This study showed that investigated parking lots were rarely contaminated with hazardous heavy metals. The heavy metal pollution of ground roof were higher than those of ground and underground indoors. The correlation analysis among trace elements suggest that components in ground roof were more highly correlated than those in ground and underground indoor. Also anthropogenic trace element levels were well correlated with parking lot age and parking density.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.33 no.2
• /
• pp.171-187
• /
• 2023

Objectives: Aircraft cabin cleaning work is characterized by being performed within a limited time in a narrow and enclosed space. The objective of this study was to evaluate the exposure levels to dust, ultra fine dust(PM2.5) and black carbon(BC) among aircraft cabin cleaners. Methods: Active personal air sampling for respirable dust(n=73) and BC(n=47) was conducted during quick transit cleaning(cabin general and vacuum-specific) and seat cover replacement and total dust and PM2.5 were area-air-sampled as well. Also, size distribution of particle was identified with the cleaning workers targeted. Dusts were collected with PVC filters using gravimetric analysis. The concentration of PM2.5 and the particle size distribution were measured with real-time direct reading portable equipment using light scattering analysis. The concentration of BC was measured by aethalometer(filter-based real-time light absorption analysis instrument). Results: The geometric mean of respirable dust was the highest at vacuum cleaning as 74.4 ㎍/m³, following by replacing seat covers as 49.3 ㎍/m³ and cabin general cleaning as 47.8 ㎍/m³ . The arithmetic mean of PM2.5 was 4.83 ~ 9.89 ㎍/m³ inside the cabin, and 28.5~44.5 ㎍/m³ outside the cabin(from bus and outdoor waiting space). From size distribution, PM_2.5/PM₁₀ ratio was 0.54 at quick transit cleaning and 0.41 at replacing seat covers. The average concentration of BC was 2~7 ㎍/m³, showing a high correlation with the PM2.5 concentration. Conclusions: The hazards concentration levels of aircraft cabin cleaners were very similar to those of roadside outdoor workers. As the main source of pollution is estimated to be diesel vehicles operating at airports, and it is necessary to replace older vehicles, strengthen pollutant emission control regulations, and introduce electric vehicles. In addition, it is necessary to provide as part of airport-inftastructure a stable standby waiting space for aircraft cabin cleaners and introduce a systematic safety and health management system for all workers in the aviation industry.

• Korean Journal of Environment and Ecology
• /
• v.38 no.4
• /
• pp.426-433
• /
• 2024

In this study, to estimate the effects of plant-induced surface area increase and physiological activity on fine dust purification, a control group was set up. We utilized both foliage plants (Spathiphyllum wallisii) and artificial plants (shaped like Spathiphyllum wallisii) to measure and compare the purification time for fine dust. The results showed that the time required for fine dust purification in each experimental group decreased by 57-64% for Type AP and 31-32% for Type P compared to the control group. Subsequently, using a Linear Mixed Model (LMM), we tested the interaction between time and each experimental group, revealing statistically significant interactions between surface area increase and time(PM10 : t=3.123, p<0.05, PM2.5 : t=3.180, p<0.05), as well as physiological activity and time(PM10 : t=4.065, p<0.05, PM2.5 : t=4.307, p<0.05), indicating the presence of interactions between each factor and the time variable. Finally, we estimated the efficiency of fine dust purification by plant factors through nonlinear regression analysis. Compared to the control group without purification factors (Type C), it was estimated that surface area increase shortened the purification time by 1.40 times and physiological activity by an average of 1.95 times, resulting in a total 2.74 times shorter purification time. Based on these results, we hypothesized that physiological activity(transpiration and absorption) has a greater impact on fine dust purification than surface area increase(biosorption). Accordingly, we emphasize the importance of vegetation management practices such as pruning and irrigation management in green spaces aimed at fine dust purification.