• Journal of Power Electronics
• /
• v.2 no.2
• /
• pp.146-153
• /
• 2002

this paper presents an implementation of digital control system of speed sensorless for Reluctance Synchronous Motor (RSM) drives with direct torque control (DTC). The problem of DTC for high-dynamic performance RSM drive is generating a nonlinear torque due to a saturated nonlinear inductance curve with various load currents. The control system consists of stator flux observer, compensating inductance look-up table, rotor position/speed/torque estimator, two hysteresis band controllers, an optimal switching look-up table, IGBT voltage source unverter, and TMS320C31 DSP controller. The stator flux observer is based on the combined voltage and current model with stator flux feedback adapitve control that inputs are the compensated inductances, current and voltage sensing of motor terminal with estimated rotor angle for wide speed range. The rotor position is estimated rotor speed is determined by differentiation of the rotor position used only in the current model part of the flux observer for a low speed operation area. It does not requrie the knowledge of any montor paramenters, nor particular care for moter starting, In order to prove the suggested control algorithm, we have simulation and testing at actual experimental system. The developed sensorless control system is showing a good speed control response characterisitic result and high performance features in 20/1500 rpm with 1.0Kw RSM having 2.57 ratio of d/q reluctance.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.2
• /
• pp.35-42
• /
• 2004

The control systems with friction cause the steady state error and slow response, because friction is a sensitive to the change of system condition and has highly nonlinear characteristics. To overcome these problems and do precise position control for a ball-screw system, we use Coulomb friction estimator and the sliding mode control(SMC) to compensate its negative effect. The applied SMC for tracking position has a characteristics of robust stability and reducing chattering, and is derived from the Lyapunov stability theorem and reaching condition. Compensating the estimated friction torque to the bounded disturbance term of the SMC's equivalent control input, it has a tracking performance better than the PID from the experimental results.

• Journal of Advanced Marine Engineering and Technology
• /
• v.24 no.6
• /
• pp.102-109
• /
• 2000

In this industrial induction motor speed and torque controlled drive system, the closed loop control usually requires the measurement of speed or position of amotor. However a sensorless drive of an induction motor has several advantages ; low cost and mechanical simplicity. Thus this paper investigates a field oriented control method without speed and flux sensors. The proposed control strategy is based on the Model Reference Adaptive System(MRAS) using a new flux estimator which replaces integrators with two lag circuits as the reference model. This algorithm may overcome several shortages of conventional MRAS such as integrator problems, small EMF at low speed. The simulation and experimental results indicate good speed responses.

• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.8
• /
• pp.1261-1267
• /
• 2009

The Direct Torque Control[DTC] controls torque and flux by restricting the flux and torque errors within respective hysteresis bands, and motor torque and flux are controlled by the stator voltage space vector using optimum inverter switching table. And the Current Error Compensation method is on the basis of compensating current difference between the induction motor and its numerical model, in which the identical stator voltage is supplied for both the actual motor and the model so that the gaps between stator currents of the two can be forced to decay to zero as time proceeds. Consequently, the rotor speed approaches to the model speed, namely, setting value and the system can control motor speed precisely. This paper proposes a new sensorless speed control of induction motor using DTC and Current Error Compensation, which requires neither shaft encoder, speed estimator nor PI controllers. And through computer simulation, confirm effectiveness of proposed method.

• Journal of Institute of Control, Robotics and Systems
• /
• v.18 no.7
• /
• pp.680-687
• /
• 2012

One of the frequent problems in the stabilized gimbal system is the rejection of disturbances associated with moving components. Very often such disturbances have non-linear characteristics. In a typical gimbal system, each gimbal and platform are connected by a mutual bearing which induces inevitable friction. Particularly, the non-linear Coulomb friction causes position errors as well as slow responses that lead to unfavorable performance. In this paper, a modified PID controller that is augmented by Coulomb friction estimator is presented. Through constantly estimating the Coulomb friction torque, it is applied to the output of the existing PID controller. The effectiveness of the proposed controller is evaluated through a series of experiments.

• Journal of Power Electronics
• /
• v.6 no.1
• /
• pp.29-37
• /
• 2006

A sensorless control for an IPM (Interior Permanent Magnet) synchronous motor in a single piston rotary compressor is presented in this study. The rotor position is estimated from the d-axis and q-axis current errors between the real system and a motor model of the position estimator. The torque pulsation of the single piston rotary compressor is compensated to reduce speed ripples, as well as, mechanical noise and vibration. The proposed sensorless drive enables the compressor to operate at a lower speed which increases energy savings and reduces mechanical noise. It also gives high speed operations by a flux weakening control for rapid air-cooling and heating of the heat pump air-conditioners.

• Proceedings of the KIEE Conference
• /
• 2000.07b
• /
• pp.1046-1049
• /
• 2000

A direct torque control(DTC) based sensorless speed control system which employs a new closed loop flux observer is proposed. The flux observer is an adaptive gain scheduling observer where motor speed is used as the scheduling variable. Adaptive nature comes from the fact that the estimates of stator resistance and speed are included as observer parameters. Simulation results show that the proposed flux observer gives better control and estimation results than conventional flux estimator specially in low speed region.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.26 no.5
• /
• pp.40-47
• /
• 2012

The PMSM position sensor using two rectangular hall sensors can restrictively acquire the 90[$^{\circ}$] position information of rotor according to electrical angle. Thus, the control method using this position sensor cannot react properly to a rapid load torque change. On the other hand, even though a sensorless method has the advantage of acquiring instantaneous rotor position information, the accuracy of position sensor can be determined by the gain value of estimator. This paper suggests a robust speed control method on torque fluctuation condition, which combines low cost two rectangular hall sensors and sensorless control method.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.5
• /
• pp.77-87
• /
• 1995

In-process detection of drill wear is one of the most important technoligies for automatic, unmaned machining systems. In this study, an on-line drill wear estimation model based on spindle/Z-axis motor currents generated during the drilling process is proposed. The theoretical model is obtained by integrating the drilling process model and the servomechanism model. The drilling process model describes the relationship of drill wear and drilling torque/ thrust force, whereas the servomechanism model describes the relationship of drilling torque/ thrust force applied to motor and spindle/Z-axis motor current. Evaluation tests have shown that the proposed model is a good real-time estimator for drill wear.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.648-651
• /
• 1996

Samsung Electronics has developed high performance velocity and position controller for induction motors, and succeeded in mass production for the first time in Korea. Dynamic performance and final control accuracy of the controller are equivalent to those of AC servo motor controller. At present, we adopted the controller as spindle motor drive for Samsung CNC systems, and expect its wide use in industry as general purpose velocity and position controller for induction motor.