• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.2
• /
• pp.203-209
• /
• 2015

Recently, the portion of electronic control in an engine system has been increasing with the aim of meeting the requirements of emissions and fuel efficiency of the engine system in the construction machinery industry. Correspondingly, the complexity of the engine management system (EMS) has increased. This study developed an engine HiLS system for reducing the cost and time required for function development for the EMS. The engine model for HiLS is composed of air, fuel, torque, and dynamometer models. Further, the mean value method is applied to the developed HiLS engine model. This model is validated by its application to a heavy-duty diesel engine equipped with an exhaust gas recirculation system and a turbocharger. Test results demonstrate that the model has accuracy greater than 90 and also verify the feasibility of the virtual calibration process.

• Journal of Aerospace System Engineering
• /
• v.12 no.2
• /
• pp.1-6
• /
• 2018

The torque ripple that is generated by the irregularity of magnetic flux density on the BLDC motor in a satellite actuator degrades the satellite attitude control performance. In this paper, the performance analysis of permanent magnet configurations (shape, arrangement, and air gap) is simulated by the Finite Element Method (FEM) to find the appropriate combination of the configuration. The configuration is chosen by comparing between rectangular and arc-shaped permanent magnets and single-arrangement and dual-arrangement magnets. The performance is verified by a prototype.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.1
• /
• pp.136-142
• /
• 2015

In the paper, a design method of knee and pelvis joint in the biped robot is proposed for shock absorption and gravity compensation. Similarly to the human's body, the knee joints of the biped robot support most body weight and get a shock from the landing motion of the foot on the floor. The torque of joint motor is also increased sharply to keep the balance of the robot. Knee and pelvis joints with the spring are designed to compensate the gravity force and reduce the contact shock of the robot. To verify the efficiency of the proposed design method, we develope a biped robot with the joint mechanism using springs. At first, we experiment with the developed robot on the static motions such as the bent-knee posture both without load and with load on the flat ground, and the balance posture on the incline plane. The current of knee joint is measured to analyze the impact force and energy consumption of the joint motors. Also, we observe the motor current of knee and pelvis joints for the walking motion of the biped robot. The current responses of joint motors show that the proposed method has an effect on shock reduction and gravity compensation, and improve the energy efficiency of walking motions for the biped robot.

• Journal of Biomedical Engineering Research
• /
• v.18 no.4
• /
• pp.447-456
• /
• 1997

When the disabled is operating a rehabilitation assisting system with a joystick by himself, unlike in the case of a normal person, tremor with joystick control or instant miscontrol can often occur. If these misoperations should be directly relayed to the system, shaking or malfunction of the mobile rehabilitation assisting system might be the result. The safety of the disabled is of prime concern. To solve this problem, that is, to prevent the miscontrol of the disabled operator and avoid crashes into his or her surroundings, we propose the force-reflection locomotion algorithm with the joystick. This method uses ultrasonic sensors to measure the distance between the object and mobile robot. Based on the reception of sensory data, the necessary torque is applied via the joystick to the attatched motor. To confirm the effectiveness of the proposed method, the subjects on the reflected force by the dynamic characteristics of the joystick and the reflected force by the distance information are tested Even though there are some differences in human dexterity, we confirmed the fact that the information from the obstacles was relayed to the operator via the joystick and resulted in an improved operational performance and safety level with regard to those obstacles.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.1
• /
• pp.52-60
• /
• 2005

Generally, a voltage difference or voltage distortion exists between the reference voltage and the practical voltage applied to a motor in a pulse width modulated(PWM) voltage source inverter(VSI). This voltage distortion varies with the operating conditions such as the temperature, DC link voltage, and phase current level. Also the voltage distortion affects the machine current distortion, torque pulsations, and control performance. In this paper, the voltage distortion in a PWM VSI is analyzed and a new on-line estimation method based on the model reference adaptive system(MRAS) is proposed to compensate the time varying voltage distortion, while considering the parameter variations for a permanent magnet synchronous motor (PMSM). The simulation and experimental results show the effectiveness of the proposed voltage difference observer and the compensation method.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.8 no.4
• /
• pp.748-757
• /
• 2007

This paper is intended to solve the technical problem that fails in large-capacity induction motor starting due to serious voltage drop during starting period. One induction motor that is established already can reach in steady-state using reactor starting method but the voltage magnitude of PCC (point of common coupling) has dropped down a little. When the same capacity induction motor is installed additionally in the PCC, where the existing induction motor is operating, voltage drop becomes more serious by starting of additional induction motor. As a result, the additional induction motor fails in starting. Therefore, voltage compensation method is proposed so that all of two induction motors can be started completely. First, modeling technique is described in order to implement starting characteristics of large induction motor. And then, this paper proposes strategic starting scheme by proper voltage compensation that use no-load transformer tap control (NLTC) and step voltage regulator (SVR) for starting of two large induction motors successfully and improving the feeding network voltage profile during the starting period. The induction motor discussed in this paper is the pumped induction motor of 2500kVA capacity that is operating by KOWACO (Korea Water Resources Corporation). Modeling and simulation is conducted using PSCAD/EMTDC software.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.50 no.5
• /
• pp.229-237
• /
• 2001

Until recent years, most of the researches for motor drives focus on the high performance drive of the three phase induction motor, and that of the single phase induction motor(SPIM) is out of interest. The SPIM is widely used at low power level because it has the simple construction and economic advantage. In general such machine has both main winding and auxiliary winding. Conventionally, these winding are fed by only one single phase source, and the speed of the motor is not controlled. The SPIM with an auxiliary winding can be treated as an asymmetrical two phase machine. In this paper the space vector Equivalent circuit of SPIM is derived. For vector control of the SPIM the stator current must be decoupled into the flux producing component and the torque producing component. To accomplish decoupling control, the conventional method requires complex calculation and large computation time. We proposed the equivalent circuit referred to the rotor side, in this case only the stator resistances in the direct axis and the quadrature axis are different each other and the other parameters are represented to be equal. Thus the decoupling of the stator current is similar to that of the three phase induction motor. In this paper, the novel vector control system of the single phase induction motor is proposed. To verify the feasibility of this scheme, simulation and experimentation are carried out. The results prove the excellent characteristics for the dynamic response, which confirms the validity of the proposed system.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.2
• /
• pp.1059-1065
• /
• 2014

Wind turbine system can obtain the maximum wind energy using torque control under the rated wind speed, and wind turbine power is controlled as the rated power using pitch control over the rated wind speed. In this paper, we present a method for wind turbine pitch controller using neural networks. The purpose of the pitch control is to control generator speed and power in the above rated wind speed. To improve the neural network pitch controller, the difference between a rated and current speed of generator has been used for another input of neural networks as well as wind speed. Error back-propagation algorithm is used for training the neural network pitch controller and simulation and Matlab/Simulink is used for verifying that this system is controlled well.

• Journal of Drive and Control
• /
• v.16 no.4
• /
• pp.80-86
• /
• 2019

The gerotor type device is mainly used in low-speed, high-torque hydraulic motors, and is also applied as a small priming hydraulic pump. For this reason, many studies have been conducted to increase the efficiency of the gerotor pump. In this paper, we propose a new tooth profile design method different from the existing method. The new tooth design is made by modifying the tooth surface using the amplification function of the trajectories, created along the inner and outer rolling circles around the base circle. The shape of the mate rotor is then created using rotation simulation techniques. Such shapes are described as hypercloid. The designed hypercloid rotor is compared with the existing trochoid rotor, and the characteristics of the parameters and volumetric displacements are analyzed. Through this process, the optimum design with larger volumetric displacement than the existing rotor is achieved.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.21 no.6
• /
• pp.499-505
• /
• 2011

This paper presents optimal design of controllable magnetorheological suspension unit for a tracked vehicle. As a first step, a double-rod type MR suspension unit is designed on the basis of the Bingham model of commercially available MR fluid, and its damping characteristics are evaluated with respect to the intensity of the magnetic field. Subsequently, the governing equation of motion of the MR suspension system featuring the MR valve is established. Then, the optimization problem to find optimal geometric dimensions of the MR supension unit is formulated by considering an objective function which is related to damping torque and control energy. The first order optimization method intergrated with a commercial finite element method(FEM) software is adopted to obtain optimal solution of the system. The performance characteristics of the optimized MR susepnsion unit is then evaluated and compared with initial one.