• 산업기술연구
• /
• 제18권
• /
• pp.323-328
• /
• 1998

A current controlled VSI-PWM rectifier and inverter with capacitor dc link is regarded as one of the most promising structures for three-phase to three-phase to three-phase power conversion. This type of converter normally requires twelve switches for a rectifier and inverter composed of self turn-off switch such as a bi-polar transistor or IGBT with an anti-parallel diode. In this paper, a new three-phase to three-phase converter for ac motor drives is proposed. The proposed converter employs only eight switches and has the capability of delivering sinusoidal input currents with unity power factor and bidirectional power flow. This paper describes the feasibility and the operational limitations of the proposed structure. A mathematical model of the system is derived using generalized modulation theory and experimental results for steady state and dynamic behavior are presented to verify the developed model.

• Journal of Power Electronics
• /
• 제14권4호
• /
• pp.621-631
• /
• 2014

To invigorate the tapped-inductor boost (TIB) topology in emerging high step-up applications for off-grid products, a lossless snubber consisting of two capacitors and three diodes is proposed. Since the switch voltage stress is minimized in the proposed circuit, it is allowed to use a device with a lower cost, higher efficiency, and higher availability. Moreover, since the leakage inductance is fully utilized, no effort to minimize it is required. This allows for a highly productive and cost-effective design of the tapped-inductor. The proposed circuit also shows a high step-up ratio and provides relaxation of the switching loss and diode reverse-recovery. In this paper, the operation is analyzed in detail, the steady-state equation is derived, and the design considerations are discussed. Some experimental results are provided to confirm the validity of the proposed circuit.

• 전기전자학회논문지
• /
• 제27권4호
• /
• pp.450-455
• /
• 2023

태양광 패널의 큰 기생 커패시턴스에 기인하는 과도한 누설 전류를 피하기 위한 단상 태양광 인버터 중에 부스트 컨버터와 하프브리지 인버터를 종속적으로 결합하는 방식은 가장 단순하면서 누설 전류가 가장 작다. 하지만 직류단 전압이 높아 스위칭 소자의 정격 전압이 높고 스위칭 손실이 크다. 본 논문은 부스트 컨버터를 제거하는 대신에 하프브리지 인버터의 출력 측에 2개의 양방향 스위치를 추가함으로써 벅부스트 인버터로 동작할 수 있는 새로운 회로 토폴로지를 제안한다. 고전압 직류단을 거치는 두 단계의 전력 변환을 한 단계로 줄인 덕분에 전력 손실을 절감할 수 있으며 비용 및 누설 전류는 증가하지 않는다. 제안된 회로 토폴로지의 타당성은 컴퓨터 시뮬레이션 및 전력 손실 계산을 통해 검증한다.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• 제5B권4호
• /
• pp.343-349
• /
• 2005

This paper proposes a novel zero-voltage-switching (ZVS) Push-pull DC-DC Converter for high input voltage and high power applications. This topology utilizes two switches in series to replace one switch in conventional push-pull converter, and two clamping diodes are introduced. The voltage stress of the switches is the input voltage, and the switches can realize ZVS with the use of the leakage inductance of the transformer. Furthermore, secondary full-wave rectifier with a clamping capacitor is used to eliminate the voltage oscillation and spike of the rectifier diodes due to the reverse recovery. Therefore, the electromagnetic interference is reduced effectively. The operation principle of the proposed converter is analyzed theoretically. The output characteristic, ZVS condition and design principle of the clamping capacitor are discussed. Experimental results obtained from a 270V input 2kW prototype with $95.8\%$ high efficiency confirms the design.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2009년도 춘계학술대회 논문집
• /
• pp.336-339
• /
• 2009

In this paper, such as battery power or solar energy and fuel cells generated from Renewable energy sources, high voltage to low voltage DC-DC Converter for converting the design of the study. System consists of low voltage ($24{\sim}28$ [VDC]) and Boosts the voltage (270 [VDC]) for a 3 [kW] DC-DC converter and control circuit is configured as, Power switch the ST Tomson's Automotive low voltage high current MOSFET switches STE250NS10S (temperature 250A) was applied to the two parallel. Also, Controller's processor used ATMEGA128, and Gate Drive applies and composed Photo Coupler TLP250. development. Input voltage (24V) and output voltage (270V) for Conversion in the H-bridge converter topology of the circuit output side power and voltage to control the implementation of the Phase shift angle control applied. And, 3kW of power to pass appropriate specification of the secondary side as interpreted by the high frequency transformer, and the experimental production and analysis of the experiment

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• 제5B권4호
• /
• pp.366-373
• /
• 2005

This paper presents two new circuit topologies of the dc busline side active resonant snubber assisted voltage source high frequency link soft switching PWM full-bridge dc-dc power converters acceptable for either utility ac 200V-rms or ac 400V-rms input grid. These high frequency switching dc-dc converters proposed in this paper are composed of a typical voltage source-fed full-bridge PWM inverter, high frequency transformer with center tap, high frequency diode rectifier with inductor input filter and dc busline side series switches with the aid of a dc busline parallel capacitive lossless snubber. All the active switches in the full-bridge arms as well as dc busline snubber can achieve ZCS turn-on and ZVS turn-off transition commutation with the aid of a transformer leakage inductive component and consequently the total switching power losses can be effectively reduced. So that, a high switching frequency operation of IGBTs in the voltage source full bridge inverter can be actually designed more than about 20 kHz. It is confirmed that the more the switching frequency of full-bridge soft switching inverter increases, the more soft switching PWM dc-dc converter with a high frequency transformer link has remarkable advantages for its power conversion efficiency and power density implementations as compared with the conventional hard switching PWM inverter type dc-dc power converter. The effectiveness of these new dc-dc power converter topologies can be proved to be more suitable for low voltage and large current dc-dc power supply as arc welding equipment from a practical point of view.

• 전자공학회논문지SC
• /
• 제40권1호
• /
• pp.39-44
• /
• 2003

휴대용 전자기기가 많이 개발되고 보급됨에 따라서 배터리의 중요성은 점점 커져가고 있다. 기기의 수명을 늘이고자 고전력밀도의 배터리를 요구하게 되었고, 현재에는 리튬-이온 배터리를 많이 사용하게 되었다. 단위체적 및 중량당의 전력밀도 부분에서는 기존에 사용하던 배터리보다 성능이 우수하지만, 방전전압이 감소하는 특성이 있기 때문에 배터리의 수명을 최대한 늘리기 위해서는 이 특성에 알맞은 컨버터가 필요하다. 그래서 리튬-이온 배터리를 사용하는 휴대용 저전력 전자기기의 전원부로써 용량성 아이들링 SEPIC을 제안하였다. 승압과 강압이 가능한 SEPIC의 특성을 가지면서, 추가된 스위치와 다이오드를 통해서 스위치에 부분적인 소프트 전환을 가능하게 하기 때문에, 스위칭 주파수의 증가를 가능하게 한다. 본 논문에서는 직류 정상상태의 전압전환비, 동작모드별 회로 및 회의특성을 분석하고 구현하였다.