• Journal of Welding and Joining
• /
• 제18권4호
• /
• pp.28-37
• /
• 2000

In this paper the LNG vessel of the Moss type which is capable of lifting 15,261 tons is investigated in the view point of the pressure vessel preliminary design using the finite element method. The Pressure vessel design is based on the equivalent stress levels due to the internal pressure. The finite element model of the spherical pressure vessel is configured using 4 noded quadrilateral shell element. The finite element analysis program NASTRAN and ANSYS 5.5are implemented. The design is compared with the three kinds of the boundary condition : first, where the equator of the pressure vessel is fixed, and where the top and is fixed, and, the bottom end is fixed, respectively. A comparison is presented between the results obtained by the finite element model and by the prototype production model. Additionally just below position(case 1 & case 2) of equator ring was carried out by using ANSYS 5.5. The results show that the vessel design based on the stress is acceptable at the preliminary design.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1994년도 추계학술대회 논문집
• /
• pp.590-596
• /
• 1994

In a CGL(Continuous Galvanizing Line) in steel making plants, zinc-coated steel sheets are produced. These sheets are used where long running corrosion resistivity is required. During the coating process top dross is produced, being harmful to the quality of the coating. To collect and remove this top dross, an automation system is developed consisting of a robot and its carriage system, a pot level sensor, a system controller, and specialtools. Forthe first, the level of the pot must be measured and fed back to the robot controller to avoid submersion of the robot hand in the hot pot. In this paper,acoustic and laser distance sensors are tested for the appropriate pot lvel sensor, especially the former in the view point of hot environment.

• 한국항공운항학회지
• /
• 제17권3호
• /
• pp.40-50
• /
• 2009

Avionics system's function for an air transport mission is analysed. The starting point for designing a Avionics system is a clear understanding of the mission requirements and the requirement allocation by the top level aircraft system. Therefore, the analysis begins by making a top-down analysis to the aircraft missions. The baseline mission is divided into segments, and each segment is subjected to a detailed analysis to establish the requirements for the Avionics system. Special attention is given to capture the key aspects of interfaces, and to incorporate them into the design.

• International Journal of Fuzzy Logic and Intelligent Systems
• /
• 제10권1호
• /
• pp.37-42
• /
• 2010

Final year students are normally encountering high pressing in their study. In view of this fact, this research focuses on determining mental states condition of college student in final year based on the psycho-physiological information. The experiments were conducted in two times, i.e., prior- and post- graduation seminar examination. The early results indicated that the student profile of mood states (POMS) in prior final graduation seminar showed higher scores than students in post final graduation seminar. Thus, in this research, relation between biosignal representing by heart rate variability (HRV) and questionnaire responses were evaluated by hidden Markov model (HMM) and neural networks (NN).

• 대한원격탐사학회:학술대회논문집
• /
• 대한원격탐사학회 2002년도 Proceedings of International Symposium on Remote Sensing
• /
• pp.292-296
• /
• 2002

This study has been accomplished as a experimental study for field application of 3D Perspective Image Map creation using Digital Topographical Map and based on the Ortho-Projection Image which is generated from Satellite Overlay Images and the precise Relative Coordinates of longitude, latitude and altitude which is corrected by GCP(Ground Control Point). AS to Contour Lines Map which is created by Coordinate conversion of 1:5,000 Topographical Map, we firstly made Satellite Image Map to substitute for Digital Topographical Map through overlapping the original images on top of each Ortho-Projection Image created and checking the accuracy. In addition to 3D Image Map creation for 3D Terrain analysis of a target district, Slope Gradient Analysis, Aspect Analysis and Terrain Elevation Model generation, multidirectional 3D Image generation by DEM can be carried out through this study. This study is to develop a mapping technology with which we can generate 3D Satellite Images of a target district through the composition of Digital Maps and Facility Blueprint and arbitrarily create 3D Perspective Images of the target district from any view point.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.278-283
• /
• 2003

Analysis has been carried out to investigate the temperature variation and the uniformity of the temperature distribution of the glass panel by infrared radiant heating. Halogen lamps are used to heat the panel and located near the top and bottom of the rectangular chamber. The thermal energy is transfered only by radiation and the radiation exchange occurs only on the solid surfaces and is considered by using the view factor. The results show that the uniformity of the temperature distribution of the panel is improved but the time for heating increases as the wall reflectivity is large. The temperature difference reaches a maximum in the early stage of the heating process and then decreases until it reaches the uniform steady-state value.

• Journal of the korean society of oceanography
• /
• 제31권1호
• /
• pp.37-42
• /
• 1996

Acartia bifilosa has been classified as Rostratae group of Acartia by the characteristic of having the rostral filament. However, we have found that A. bifilosa does not have any rostrum. Therefore, A. bifilosa should be classified as Arostratae group. For the first time, we have observed that this species has only one genital pore in the genital segment. Two spermathecal canals are looped in lateral view as well as ventral view. We have also observed two thin, very short filaments and minute apertures on the anterio-ventral part of the top of the head. The function of the filaments need to be investigated.

• Asia pacific journal of information systems
• /
• 제7권3호
• /
• pp.61-87
• /
• 1997

Recently, strategic information systems planning (SISP) has emerged as one of the necessities in 15 activities and organizational operations as a whole. Although various SISP researches have been done, in few studies have attention been given to the process employed in organizations to plan and implement SISP. To address SISP problems in terms of the process-oriented view, this paper employs a dynamic viewpoint on the basis of innovation-process model As a result of in-depth interviews with IS managers of nine Korean banks, this research found slightly different problems appear in each stage of the process. While problems cited in prior researches were observed, new ones are also appeared such as "finding out relative outsourcers" "political problems between functions which lead the process and others which alienated," the "necessity of steering committees, etc. Meanwhile, problems such as "top management concerns" or "cost," which suggested as significant problems in prior researches, appeared relatively insignificant This study has limitations as a qualitative and exploratory one. However, in view of further studies, the linkage between SISP practices and innovation process theory will allow researches linking characteristics of both fields. Furthermore, researches which view the SISP process as a comprehensive knowledge transfer process will be possible.

• ETRI Journal
• /
• 제39권1호
• /
• pp.97-107
• /
• 2017

A fast and accurate building-level visual place recognition method built on an image-retrieval scheme using street-view images is proposed. Reference images generated from street-view images usually depict multiple buildings and confusing regions, such as roads, sky, and vehicles, which degrades retrieval accuracy and causes matching ambiguity. The proposed practical database refinement method uses informative reference image and keypoint selection. For database refinement, the method uses a spatial layout of the buildings in the reference image, specifically a building-identification mask image, which is obtained from a prebuilt three-dimensional model of the site. A global-positioning-system-aware retrieval structure is incorporated in it. To evaluate the method, we constructed a dataset over an area of $0.26km^2$. It was comprised of 38,700 reference images and corresponding building-identification mask images. The proposed method removed 25% of the database images using informative reference image selection. It achieved 85.6% recall of the top five candidates in 1.25 s of full processing. The method thus achieved high accuracy at a low computational complexity.

• 한국방송∙미디어공학회:학술대회논문집
• /
• 한국방송공학회 1996년도 Proceedings International Workshop on New Video Media Technology
• /
• pp.18-21
• /
• 1996

In the field of Virtual Reality, many studies have been reported. Especially, there are many studies on generating virtual creatures on computer systems. In this paper we propose an algorithm to automatically generate 3D fish models from 2D images which are printed in illustrated books, pictures or handwritings. At first, 2D fish images are captured by means of image scanner. Next, the fish image is separated from background and segmented to several parts such as body, anal fin, dorsal fin, ectoral fin and ventral fin using the proposed method“Active Balloon model”. After that, users choose front view model and top view model among six samples, respectively. 3D model is automatically generated from separated body, fins and the above two view models. The number of patches is decreased without any influence on the accuracy of the generated 3D model to reduce the time cost when texture mapping is applied. Finally, we can get any kinds of 3D fish models.