• Journal of dental hygiene science
• /
• v.15 no.5
• /
• pp.673-678
• /
• 2015

The purpose of this study was to evaluate the reliability and accuracy of linear measurements in digital models compared to master model. A master model (ANKA-4; Frasaco GmbH, Tettnang, Germany) with the prepared upper full arch tooth was used. Four linear measurements were recorded between landmarks, directly on the master model and the digital models by a single examiner. Measurements were made with a digital caliper from manual model and with the software from the virtual models. The t-test for paired samples and intraclass correlation coefficient (ICC) were used for statistical analysis. The measurement of two methods showed good reliability. The mean differences between master and digital model were 0.06~0.12 mm. These in vitro studies show that accuracy and reliability of the digital impression is similar to that of the gold standard. Therefore digital impression was also considered to be a acceptable for placement clinically.

• International Journal of Oral Biology
• /
• v.38 no.3
• /
• pp.87-92
• /
• 2013

Periodontal inflammation increases the risk of tooth loss, particularly in cases where there is an associated loss of alveolar bone and periodontal ligament (PDL). Histological and morphometric evaluation of periodontal inflammation is difficult. Especially, the lengths of the periodontal ligament and interdental alveolar bone space have not been quantified. A quantitative imaging procedure applicable to an animal model would be an important clinical study. The purpose of this study was to quantify the loss of alveolar bone and periodontal ligament by evaluation with micro-computed tomography (micro-CT). Another purpose was to investigate differences in infections with systemic E. coli LPS and TNF-${\alpha}$ on E. coli lipopolysaccharide (LPS) in loss of alveolar bone and periodontal ligament model on mice. This study showed that linear measurements of alveolar bone loss were represented with an increasing trend of the periodontal ligament length and interdental alveolar process space. The effects of systemic E. coli LPS and TNF-${\alpha}$ on an E. coli LPS-induced periodontitis mice model were investigated in this research. Loss of periodontal ligament and alveolar bone were evaluated by micro-computed tomography (micro-CT) and calculated by the two- and three dimensional microstructure morphometric parameters. Also, there was a significantly increasing trend of the interdental alveolar process space in E. coli LPS and TNF-${\alpha}$ on E. coli LPS compared to PBS. And E. coli LPS and TNF-${\alpha}$ on E. coli LPS had a slightly increasing trend of the periodontal ligament length. The increasing trend of TNF-${\alpha}$ on the LPS-induced mice model in this experiment supports the previous studies on the contribution of periodontal diseases in the pathogenesis of systemic diseases. Also, our findings offer a unique model for the study of the role of LPS-induced TNF-${\alpha}$ in systemic and chronic local inflammatory processes and inflammatory diseases. In this study, we performed rapidly quantification of the periodontal inflammatory processes and periodontal bone loss using micro-computed tomography (micro-CT) in mice.

• Restorative Dentistry and Endodontics
• /
• v.46 no.4
• /
• pp.47.1-47.9
• /
• 2021

Objectives: This study aimed to use a laboratory model to evaluate the efficacy of an experimental bleaching agent. Materials and Methods: The model used human extracted molars that were treated and measured for bleaching efficacy. Teeth (n = 50) were distributed into 5 groups: Negative control (NC): immersion in water for 8 hours; Nanofibers (NFs): Experimental titanium dioxide nanofibers with stirring and light activation for 8 hours; Whitestrips (WS): Crest 3D White Glamorous White Whitestrips, 2 applications daily for 30 minutes, 14 days; 1% hydrogen peroxide (HP) standard: 1% hydrogen peroxide for 8 hours; and 30% HP standard: 30% hydrogen peroxide for 8 hours. Instrumental measurements were performed using a spectrophotometer. Results were recorded at baseline, 1-day post-bleaching, and 1-week post-bleaching. Kruskal-Wallis procedure was used to determine differences in color change. Pearson correlation was used to evaluate the relationship between visual and instrumental measurements. Tests of hypotheses were 2-sided with alpha = 0.05. Results: There was no significant difference in color parameters (L1, a1, b1, and shade guide units [SGU]) at baseline (p > 0.05). There was a significant difference among the groups for overall color change (ΔE^*ab) and change in shade guide units (ΔSGU) at 1-day and 1-week post-bleaching (p < 0.05). The higher the HP concentration, the higher the color change as expressed in ΔSGU and ΔE^*ab. The negative control exceeded the perceptibility threshold of ΔE^* = 1.2 regardless of time point. NFs showed a decrease in chroma, but were not statistically different compared to the negative control. Conclusions: The laboratory model was successful in screening an experimental bleaching agent.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.7
• /
• pp.143-148
• /
• 2001

In this study, a mechanistic model of cutting force components in up and down end milling process is presented. Using this cutting force model of 4-tooth endmills with various helix angles, cutting force variation of inconel 718 has been predicted. Predicted values of cutting force components are coincide well with the measured ones. As helix angle increases, overlapping effects of the active cutting edges increase. In up endmilling the magnitudes of radial and feed cutting force componts FX and FY are lowest when the helix angle is $40\{\circ}$, but in down endmilling the magnitudes of these values increase slightly as helix angle becomes large.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.10
• /
• pp.36-45
• /
• 1996

The precise estimation of the reliability and life of the Ravigneaux planetary gear train used in an automatic transmission is necessary in order to enable accurate material and geometric properties to reliability distrobution and the number of load cycles at failure. These are critical for the proba- bilistic design of complex planetary gear system as Ravigneaux type particularly during various gear ratios. The Ravigneaux planetary gear train has five gears, such as a forward and a reverse sun gear, a short and a long pinion, and an annulus gear. In this paper, the Ravigneaux gear system is analyzed to figure out the reliablity distribution. i.e. the probability of survival in the system without its overhaul. First, the reliablity method based on the Weibull distribution is used in conjuction with the Palmgren's model to predict both the individual reliabilities of its components and the nimber of load cycles when the system failed. Then using the presented method, the life of the Ravigneaux gear system can be determined. Alwo the different design parameters such as tooth face width, material property, and Weibull exponent are applied and reached to optimal ones. Thus, the precise evaluation of the reliability and life of the Ravigneaux planetary gear train used in an automatic transmission can be effectively carried out.

• The Journal of Advanced Prosthodontics
• /
• v.8 no.5
• /
• pp.380-387
• /
• 2016

PURPOSE. The storage conditions of impressions affect the dimensional accuracy of the impression materials. The aim of the study was to assess the effects of storage time on dimensional accuracy of five different impression materials by cone beam computed tomography (CBCT). MATERIALS AND METHODS. Polyether (Impregum), hydrocolloid (Hydrogum and Alginoplast), and silicone (Zetaflow and Honigum) impression materials were used for impressions taken from an acrylic master model. The impressions were poured and subjected to four different storage times: immediate use, and 1, 3, and 5 days of storage. Line 1 (between right and left first molar mesiobuccal cusp tips) and Line 2 (between right and left canine tips) were measured on a CBCT scanned model, and time dependent mean differences were analyzed by two-way univariate and Duncan's test (${\alpha}=.05$). RESULTS. For Line 1, the total mean difference of Impregum and Hydrogum were statistically different from Alginoplast (P<.05), while Zetaflow and Honigum had smaller discrepancies. Alginoplast resulted in more difference than the other impressions (P<.05). For Line 2, the total mean difference of Impregum was statistically different from the other impressions. Significant differences were observed in Line 1 and Line 2 for the different storage periods (P<.05). CONCLUSION. The dimensional accuracy of impression material is clinically acceptable if the impression material is stored in suitable conditions.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.16 no.7 s.112
• /
• pp.697-703
• /
• 2006

This article proposes a new technique for the reduction of vibration and noise in the geared system by adjusting the distance between gear shafts. The vibration and noise may be produced by the abnormal force applied to the tooth face. And the force may be the cause of ununiform velocity in the driven shaft. If the velocity is obtained to be uniform by adjusting the distance between shafts. the vibration and noise may be reduced to some extent. In order to review, a dynamic analysis model for the gear train used in a mill turret and a test rig are developed. The velocities in the driven shaft are calculated by dynamic simulations for the model and noises in the test rig are measured with varying of the distance between shafts. The comparison of simulation and test data shows that the distance between shafts at the most uniform velocity has the lowest level of noise.

• The Journal of Korean Academy of Prosthodontics
• /
• v.31 no.2
• /
• pp.207-218
• /
• 1993

The purpose of this study was to evaluate the reproducing accuracy of stone casts made from complete arch impressions using different impression materials. The impression materials studied were 1) polyether, 2) polysulfide, 3) polyvinyl siloxane, and 4) irreversible hydrocolloid. Impressions were made from a partially edentulous acrylic resin model with metal inserts in canine, first molar region bilaterally and mid palatal vault region. Each distance between 2 out of 5 meauring points was measured by using 3dimensional measuring machine. Impressions were poured at once with a type IV dental stone. Data were analyzed using t-test with a sample size of six. The results were as follow : 1. Polysulfide and polyether were significantly superior to polyvinyl siloxane and irreversible hydrocolloid in reproducing full arch model(p<0.05), but there were no statistical differences in amount of dimensional reproducing accuracy for full arch impression between polysulfide and polyether(p>0.05). 2. There were statistical differences in amount of dimensional reproducing accuracy between edentulous area and tooth bound area for polysulfide and polyether(p<0.05). but no statistical differences were observed for polyvinyl siloxane and irreversible hydrocolloid(p>0.05).

• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.4
• /
• pp.474-481
• /
• 2011

The purpose of this study was to investigate the effect of rigidity of post core systems on stress distribution by the finite element stress analysis method. Three-dimensional finite element models simulating an endodontically treated maxillary central incisor restored with a zirconia crown were prepared. Each model contained cortical bone, trabecular bone, periodontal ligament, 4mm apical root canal filling, and post-and-core. A 50N static occlusal load was applied to the palatal surface of the crown with a $60^{\circ}$ angle to the long axis of the tooth. And three parallel type post (zirconia, glass fiber and stainless steel) and two core (Paracore and Tetric ceram) materials were evaluated, respectively. The differences in stress transfer characteristics of the models were analyzed. von Mises stresses were chosen for presentation of results and maximum displacement and hydrostatic pressure were also calculated. For the Result of the research, the model applied glass fiber to post material has lowest von Mises stress and it is suitable for material of post core systems.

• Journal of Fashion Business
• /
• v.4 no.4
• /
• pp.41-54
• /
• 2000

The purpose of this study was to investigate various expressions in textile design using CAD and present print design of '01/02 A/W. Four steps were taken in order to achieve this purpose. The first step was to investigate prior research and to analyze textile design methods using CAD. The second step was to study '01/02 A/W fashion trend, especially textile trend. The third step was to design the print design according to textile trend and apply the designed print pattern to real model. The research results are as follows: 1. Textile design is a very important field to help making fashion industry more informative and valuable. 2. Using CAD system in textile design will be very useful and urgent in saving working time and exercising design works. 3. In '01/02 A/W hound's tooth, zigzag, herringbone will be prevalent bold geometric patterns while tartan checks, multi color stripes will be popular too. 4. Textile designs using flower, stripe, checks, dot, abstract pattern were applied to real model, the images of patterns design are as follow, flower pattern-romantic stripe-avantgarde check-cute dotclassic abstract motive-intelligent.