• 한국세라믹학회지
• /
• 제36권3호
• /
• pp.274-283
• /
• 1999

1.1-nm tobermorite의 수열합성에 SiO2원으로 zeolite광물을 출발물질로하여 소석회와 Ca(Si+Al)의 몰비 0.8~1.0로 150$^{\circ}$~23$0^{\circ}C$,8~48시간 동ㅇㄴ 포화증기압하에서 수열반응을 시킨 결과, 반응초기단계에서 tobermorite가 생성되었고, 고결정성 1.1-nm tobermorite의 최적합성조건은 0.8몰, 23$0^{\circ}C$, 48시간이었다. 출발물질중 Al의 존재로 tobermorite는 Ca/(Si+Al)몰비 0.8이 1.0보다 결정화가 급속히 이루어지고 있으나 Al를 함유치 않은 석영의 경우에는 Ca/Si 몰비 1.0이 0.8에서 보다 결정화가 빠르게 진행되었다 1.1-nm tobermorite는 $700^{\circ}C$에서 일주일간 가열처리하여도 저면간격이 변화하지 않는 열적거동이 이상형임을 보여주었다. 특히 출발물질중 Al의 존재는 1.1-nm tobermorite의 결정화와 안정화를 촉진시켜주며 Al이온이 tobermorite구조중의 Si이온과 동형치환을 한다.

• 한국재료학회지
• /
• 제15권2호
• /
• pp.97-105
• /
• 2005

[ $11\AA$ ] tobermorite$(5CaO{\cdot}6SiO_2{\cdot}5H_2O)$ is synthesized from the mixtures of calcium hydroride and quartz using alumina in a molar ratio $Ca(OH)_2/SiO_2$ of 0.8 at $180^{\circ}C$ for 8 and 24 hrs under saturated steam pressure. The influence of alumina on the formation of $11\AA$ tobermorite was investigated by X-ray diffraction, differential thermal analysis and infrared spectroscopy. $11\AA$ tobermorite containing increasingly larger amounts of aluminum showed a shift of the basal spacing from 11.3 to $11.6\AA$. In general, there was a direct linear relation between the basal spacing and added content of alumina. The differential thermal analysis curves showed that $11\AA$ tobermorite with increasing alumina contents exhibited the exothermic peak at high temperature, namely $11\AA$ tobermorite containing aluminum gave a sharp exothermic peak at temperature around $850\~860^{\circ}C$ in the case of $S_3\~S_5$. The absorption band at $1607\~1620cm^{-1}$ is attributed to the bending vibration of water, and the position of the main O-H stretching and Si-O lattice vibration of $11\AA$ tobermorite at 3500 and $965cm^{-1}$ respectively is not altered. Consequently the existence of alumina accelerates the crystallization of $11\AA$ tobermorite, and that the aluminum ion appears to substitute for the silicon ion in $11\AA$ tobermorite structure. Al-containing tobermorite is distinguished from Al-free tobermorite.

• 한국세라믹학회지
• /
• 제11권4호
• /
• pp.25-30
• /
• 1974

The mixture of quartz powder and slaked lime with plenty water was oscillated in an autoclave and treated hydrothermally under the pressure of 10 kg/$\textrm{cm}^2$ for 8 hours. The main mineral synthesized was confirmed 11$\AA$ tobermorite by the method of X-ray diffraction and selected area electron diffraction. Tobermorite was heat-treated at 40$0^{\circ}C$, 80$0^{\circ}C$ and 100$0^{\circ}C$ for investigation of transformation of morphology and structure. Electron micrographs showed the thin platy structure of synthetic tobermorite with a little of crumpled foil or fibrous semi-crystalline calcium silicate hydrates. No difference in structure was appeared under the temperature of 80$0^{\circ}C$ but tobermorite converted gradually into wollastonite at 800$^{\circ}$~85$0^{\circ}C$. On heating, moulded material from tobermorite hardly shrinks under 80$0^{\circ}C$.

• 공업화학
• /
• 제4권2호
• /
• pp.291-299
• /
• 1993

생석회-규사-수계 및 시멘트 슬러지-규사-수계에서 1.13nm tobermorite를 수열합성하였다. 생석회-규사-수계의 경우 반응온도 $180^{\circ}C$, $CaO/SiO_2$의 몰비 0.4, 0.8에서 공히 양질의 tobermorite($5CaO{\cdot}6SiO_2{\cdot}5H_2O:C_5S_6H_5$)가 형성되었으나 $CaO/SiO_2$의 몰비 0.4일 때는 반응시간 6시간에서, 0.8일 때는 4시간에서 결정전이 현상이 관찰되었다. 그러나 시멘트 슬러지를 생석회 대신 전량 사용한 시멘트 슬러지-규사-수계는 동일한 몰비에서 반응시간 10시간 이내에 결정전이 현상이 나타나지 않았는데 이는 시멘트 슬러지로부터 용출되어 나온 알루미늄 이온의 지연작용으로 판단되며 생석회-규사-수+알루미늄계에서 확인되었다. 알루미늄 분말의 첨가량이 0.8에서 3.0%로 증가함에 따라 결정은 보다 넓고 평평하게 형성되었다. 또한 동일한 반응시간 내에서 재결정화 현상이 관찰되지 않았다.

• 한국세라믹학회지
• /
• 제15권1호
• /
• pp.16-20
• /
• 1978

The solubility of tobermorite was measured, and it was compaired with the resultswhich calculated by thermodynamic data. As the result, 1) The type of silisic acid species in liquid phase were the both type of $H_3SiO_4$-, $H_4SiO_4$. 2) The solubility product of tobermorite represented the maximum value at 18$0^{\circ}C$.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2005년도 춘계 학술기술논문발표대회 논문집
• /
• pp.57-60
• /
• 2005

This is the experimental study on the strength development of the light weight concrete block according to the autoclaving time. The calcareous source used the cement, siliceous material used the bottom ash ground to fine particle, and the PP fiber used to increase toughness. The results of this experiment are as follows. According to the increase of autoclaving time and the fiber content, compressive and flexural strengths are increased. Despite of the changes of the autoclaving time, tobermorite was produced on each of the specimens. However, the phase of tobermorite was changed in accordance with the changes of autoclaving time.

• 한국세라믹학회지
• /
• 제34권5호
• /
• pp.491-499
• /
• 1997

High flexible lightweight composites containing tobermorite as a main mineral is produced using various amorphous silicates, lime, cement and fibers. Here, Mechanical properties of the composites were studied by observing microstructures of hydrates and fibers. Amorphous silicates having better hydraulicity retarded the crystallization of tobermorite due to better formation of C-S-H gel in water bath curing, but, difficult conversion from C-S-H gel to tobermorite in hydrothermal reaction. In the low molar ratio of CaO/SiO2 (0.67), faster crystalization was observed dued to more impurities such as Al2O3 alkali, resulting in improving mechanical properties due to small crystal size and many contact points. It was identified that a lot of calcium silicate hydates formed at surface of pulps increase bonding strength and the crack-resistance of matrix in the composites, but decrease hardness and compressive strength. The choice of amorpous silicates having better hydraulicity, low CaO/SiO2 adding each fibers bellow about 5% in the raw mixs and lower molding pressure should be needed at improve mechanical properties of composites.

• 한국세라믹학회지
• /
• 제35권10호
• /
• pp.1030-1039
• /
• 1998

In fly ash-lime system the effects of reaction condition amounts of gypsum and cement and CaO/SiO2 ratio on the hydrates by hydrothermal reaction were investigated. The tobermorite phases were not observed in hy-drothermal reaction of fly ash lime because of the hydrate rate was very slow. The compressive strength and the hydration rate increased with increasing the amount of gypusm and cement and the optimum amounts of gypsumo and cement were 5wt and 20wt% respectively. The specimen which CaO/SiO2 ratio is 0.85 was shown the maximum compressive strength and the tobermorite phase within reaction time 2 hours.

• 한국세라믹학회지
• /
• 제37권8호
• /
• pp.811-816
• /
• 2000

This paper discussed hydrothermal reactivity of Ca(OH)2 and classified bituminous fly ashes which were collected at an electrostatic precipitator in coal fired power plant at 181$^{\circ}C$. The major products of hydrothermal reaction were tobermorite and hydrogrossularite because bituminous fly ashes contained Al2O3 content greater than 20 wt%. As increasing amount of Al2O3 content greater than 20 wt%. As increasing amount of Al2O3 in glass phases, formation of hydrogrossularite increased. Formation rate of crystalline tobermorite increased with content of finer particles, higher glass content and more Al2O3 in glass phases. There was a positive correlation between residue on 45${\mu}{\textrm}{m}$ sieve and hydrothermal reactivity of fly ash up to 3 hours. The hydrothermal reactivity of fly ash at 181$^{\circ}C$ for 12 hours was more affected by fineness than by glass content of fly ash.

• 한국세라믹학회지
• /
• 제49권6호
• /
• pp.535-541
• /
• 2012

ALC was fabricated using cement, lime, quartzite and a foaming agent via a hydrothermal reaction. ALC has various hydrothermal reaction products and many pores. The properties and colors of ALC surfaces were changed by various factors during ALC fabrication process. This study tested various staying times to analyze these phenomena. It was found that the staying time of green body influenced the properties of hydrothermal products and color of ALC surface. The longer staying time of green body, the lower tobermorite content and cumulative loss weight. An increase in holding time changed color and decreased whiteness of ALC surface. The relationship between whiteness and cumulative loss weight was very high (Coefficient, r = 0.95). It was surmised that tobermorite content was an important factor for enhancement of whiteness However, ettringite and quartzite did not contribute to whiteness.