• 한국CDE학회논문집
• /
• 제20권2호
• /
• pp.104-113
• /
• 2015

In developing a tire, many CAE analyses are performed to make a better tire. But its meshing work is not easy, and it takes much time. One of the reasons of taking much time is that there are many overlapped geometric entities in CAD data that are modeled in CAD system by CAD engineers. In this study, we studied about the features of the overlapped geometric entities, and the method to find out and delete them. I developed a program using the proposed algorithm, and applied it in meshing tire pattern and tire case. I proved that the time in meshing a tire reduced dramatically by removing overlapped geometric entities by using the developed program.

• 한국기계가공학회지
• /
• 제8권2호
• /
• pp.40-45
• /
• 2009

This study is analyzed by stress contour of automotive tire at contact on road surface. Maximum equivalent stress as 61200Pa is shown on the lower mid part in case of tire contacted on road surface. As the air pressure of tire increases, maximum total deformation as 5mm is shown on the side part of tire. It can be shown that the side part of tire is unstabilized. There is no load effect on tire at its upper and lower directions. When the moment applied on the side of tire is increased 1.4 times as its value, the value of maximum principal stress is increased 1.4 times. The stress at the tire is in proportion to the moment applied on the its side. The tire tends to incline toward its side by this moment.

• 한국도로학회논문집
• /
• 제15권4호
• /
• pp.75-83
• /
• 2013

PURPOSES: The purpose of study is to understand the characteristic of driving noise from the front and rear tire for effective active noise cancellation application. METHODS : As literature review, noise measurement methods were reviewed. Noise measurement conducted at three kind of section by road slope using CPX(Close Proximity Method). Noise data was compared by total sound pressure level and 1/3 octave band frequency sound pressure level. Also, each section was compared by T-test using SPSS. RESULTS : In the case of the uphill section, it was shown that the sound pressure level of the front tire at Sugwang-Ri and Sinchon-RI sections was higher than that of the rear tire in low and high frequency band. In the case of high slope section of Sangsaek-Ri, the sound pressure level of the front tire was higher than that of the rear tire in high frequency. Also, in the case of the downhill section, it was shown that the sound pressure level of the front tire at Sugwang-Ri and Sinchon-RI sections was higher than that of the rear tire in low frequency band. However, the sound pressure levels of both the front and rear tires were approximately the same in the high slope section of Sangsaek-Ri. The result of T-test showed that total sound pressures of the front and rear tires were not different from each other in the case of high slope and high speed. CONCLUSIONS: Road slope was not an important variable for effective active noise cancellation.

• International Journal of Automotive Technology
• /
• 제7권1호
• /
• pp.101-107
• /
• 2006

The force and moment simulation of a steady-state rolling tire taking the effect of tread pattern into account is described using a steady-state transport method with ABAQUS. Tread meshes can not fully consider a tread pattern because detailed tread meshes are not allowed in the steady-state transport method. Therefore, the tread elements are modeled to have orthotropic property instead of isotropic property. The force and moment simulation has been carried out for the cases of both isotropic and orthotropic properties of tread elements. Both cases of simulation results are then compared with the experimental results. It is verified that the orthotropic case is in a better agreement with the experimental result than the isotropic case. Angle effects of tread pattern have been studied by changing the orientation angle of orthotropic property of tread. It is shown that the groove angle in the tread shoulder region has a more effect on force and moment of a tire than that in the tread center region.

• Tribology and Lubricants
• /
• 제23권5호
• /
• pp.228-233
• /
• 2007

This paper presents the case studies on the friction related wears of an automotive tire, which is strongly connected to the safety and comfort of a driver during a running of a car. Wear scars of a tire tread are affected by various causes such as an air pressure, a wheel alignment, a driving speed, road conditions, starting and braking habits of a driver. The data were collected from used tires for a replacement at the car service center. Most of the wear problems came from the improper repair and adjustment of revolving components, which cause an unbalanced wear of a tread part of a tire. Thus, the regular checking of a tire radically reduces the wear scars of a tire and may increase a driving safety and a fuel economy of a car and a wear life of a tire.

• Geomechanics and Engineering
• /
• 제6권3호
• /
• pp.249-262
• /
• 2014

Tire chips and tire chips-soil mixtures can be used as alternative fill material in many civil engineering applications. In this study, the potential benefits of using tire chips as lightweight material to improve the bearing capacity and the settlement behavior of sand slope was investigated experimentally. For this aim, a series of direct shear and model loading tests were conducted. In direct shear tests, the effect of contents of the tire chips on the shear strength parameters of sand was investigated. Different mixing ratios of 0, 5, 10, 15 and 20% by volume were used and the optimum mixing ratio was obtained. Then, laboratory model tests were performed on a model strip footing on sand slope reinforced with randomly distributed tire chips. The loading tests were carried out on sand slope with relative density of 65% and the slope angle of $30^{\circ}C$. In the loading tests the percentage of tire chips to sand was taken as same as in direct shear tests. The results indicated that at the same loading level the settlement of strip footing on sand-tire chips mixture was about 30% less than in the case of pure sand. Addition of tire chips to sand increases BCR (bearing capacity ratio) from 1.17 to 1.88 with respect to tire chips content. The maximum BCR is attained at tire chips content of 10%.

• 제어로봇시스템학회논문지
• /
• 제21권10호
• /
• pp.903-909
• /
• 2015

This article presents an integrated chassis control with electronic stability control (ESC) and active front steering (AFS) under saturation of front lateral tire force. Regardless of the use of AFS, the front lateral tire forces can be easily saturated. Under the saturated front lateral tire force, AFS cannot be effective to generate a control yaw moment needed for the integrated chassis control. In this paper, new integrated chassis control is proposed in order to limit the use of AFS in case the front lateral tire force is saturated. Weighed pseudo-inverse control allocation (WPCA) with variable weight is adopted to adaptively use the AFS. To check the effectiveness of the proposed scheme, simulation is performed on a vehicle simulation package, CarSim. From simulation, the proposed integrated chassis control is effective for vehicle stability control under saturated front lateral tire force.

• Journal of Biosystems Engineering
• /
• 제35권1호
• /
• pp.21-30
• /
• 2010

This study was performed to develop an active tire pressure control system that can adjust tire pressure to the optimum level according to traveling and working condition of agricultural tractor. For the development of active tire pressure control system, pneumatic supplier, solenoid valve block including pneumatic supply line, infinite rotation type pneumatic supplier with rotary joint unit, tire pressure transceiver module and control algorithm were developed. Also, tire simulator was developed. Using this tire simulator, the feasibility of each part constructing actual system was tested by checking the performance. The average communication success ratio was 98.3% between tire pressure transmitter and receiver module according to the various tire rotational speed and data receipt position of receiver module. The communication performance of the developed transmitter and receiver module was very stable in any condition. The tire pressure control system was accomplished by using the proportional control algorithm in this study. Also tire pressure control performance of developed control system was analyzed by using the tire simulator. As a result of control performance analysis to the developed system, the developed control system took 307 seconds to inflate agricultural tractor's tire from 50 kPa to 180 kPa. In opposite case, it took 210 seconds. Also it was able to control the tire pressure accurately under ${\pm}0.9%$ (FS) in any condition.

• 타이어
• /
• 통권101호
• /
• pp.22-24
• /
• 1982

본고는 Polymer Friends지에 게재된 "현장의 트러블 대책"=고무공장의 사례연구(Case Study)에서 밝혀진 오랜 동안의 여러 가지의 현장경험을 토대로 한 고무공장에서의 트러블의 구체적인 예를 종합 정리하여 분석 해 본 것이다. 공장에서의 트러블은 몇 가지의 모델 케이스로 분류할 수 있는 것이 아닌가 하는 점에서 발단되었다.

• 한국인터넷방송통신학회논문지
• /
• 제15권6호
• /
• pp.291-296
• /
• 2015

주행 중인 차량의 타이어와 노면 사이에서 발생하는 랜덤성 초음파신호의 주기성을 검출하여 타이어의 손상을 분별하는 방법에 대하여 연구하였다. 잡음으로부터 타이어손상에 의한 유효한 펄스를 검출하기 위해 적응 임계치를 설정하는 방법을 제안하였고, 이를 위한 전처리로서 신호의 랜덤성을 감소시키는 저역통과필터를 사용하였다. 자동차의 속도에 따라 검출된 펄스의 시간간격을 밀도함수화하고 피크점의 시간을 측정하여 타이어 손상물질을 검출하는 방법을 제안하였다. 손상물질이 한 개이고, 주행속도가 50km/h, 80km/h, 100km/h 일 때, 시간밀도함수의 제 1 피크시간 측정결과는 각각 169.8ms, 97.9ms, 81.8ms로 주행속도에 따라 계산한 타이어 회전주기의 오차범위내로 측정되었으며, 한개 이상의 손상물질의 경우에는 각 피크시간의 합이 타이어 회전주기의 오차범위내로 측정되는 결과를 얻을 수 있었다.