• Journal of the Korean Society for Marine Environment & Energy
• /
• v.2 no.2
• /
• pp.70-77
• /
• 1999

The disturbance of oil-water interface confined between tandem fences caused by a sequence of traveling vortices below the interface is investigated. The traveling vortices are assumed to be those detached from the tip of the fore fence. The potential flow is assumed and the density interface is replaced as a sheet of vortex. The shape of the interface is predicted by tracing a finite number of marker particles placed at the interface. The velocity of the marker particles is determined by the Biot-Savart integral along the vortex sheet plus the contribution from the traveling point vortices. The rate of change of vortex-sheet strength is predicted by using an evolution equation for vorticity. The calculated results obtained for various conditions demonstrate that the large amplitude of interfacial wave following the moving vortek can be generated by the vortices.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.3
• /
• pp.414-421
• /
• 2001

The present study is conducted to investigate the local heat/mass transfer characteristics on the shroud with blade tip clearances. The relative motion between blade and shroud has little influence on the overall heat transfer characteristics, except some local effects. Therefore, the relative motion between the blade and shroud is neglected in this study. A naphthalene sublimation method is employed to determine the detailed local heat/mass transfer coefficients on the surface of the shroud. The tip clearance is changed from 0.66% to 2.85% of the blade chord length. The flow enters the gap between the blade tip and shroud at the pressure side due to the pressure difference. Therefore, the heat/mass transfer characteristics on the shroud are changed significantly from those with endwall. At first, high heat/mass transfer occurs along the profile of blade at the pressure side due to the entrance effect and acceleration of the gap flow. Then, the heat/mass transfer coefficients on the shroud increase along the suction side of the blade because tip leakage vortices are generated and interact with the main flow. The results show that the heat/mass transfer characteristics are changed largely with the gap distance between the tip of turbine blade and the shroud.

• Journal of computational fluids engineering
• /
• v.12 no.1
• /
• pp.1-8
• /
• 2007

A code is developed using the hybrid Cartesian/immersed boundary method and it is applied to simulate flows around a three-dimensional deforming body. A new criterion is suggested to distribute the immersed boundary nodes based on edges crossing a body boundary. Velocities are reconstructed at the immersed boundary nodes using the interpolation along a local normal line to the boundary. Reconstruction of the pressure at the immersed boundary node is avoided using the hybrid staggered/non-staggered grid method. The developed code is validated through comparisons with other experimental and numerical results for the velocity profiles around a circular cylinder under the forced in-line oscillation and the pressure coefficient distribution on a sphere. The code is applied to simulate the flow fields around a plate whose tail is periodically flapping under a translation. The effects of the velocity and acceleration due to the deformation on the periodic shedding of pairs of tip vortices are investigated.

• Journal of the Korean Society of Visualization
• /
• v.5 no.2
• /
• pp.20-25
• /
• 2007

The geometry of a commercial passenger airplane is realized based on a Boeing 747-400 model through the photographic scanning and reverse engineering. The each element consisting of the plane such as fuselage, wing, vertical fin, stabilizer and engines, is individually generated and then the whole body is assembled by the photomodeler. The maximum error in the realized airplane is about 1.4% comparing with the real one. The three-dimensional inviscid steady compressible governing equations are solved in the unstructured tetrahedron grid system, and in a finite volume method using STAR-CD when the airplane flies at the cruise condition. The pressure distribution on the surface and the wing-tip vortices are visualized, and in addition to the aerodynamics coefficients, lift and drag are estimated.

• Solar Energy
• /
• v.7 no.2
• /
• pp.74-85
• /
• 1987

Performances of 3 different aerodynamic analytical models, single multiple and double multiple stream tube, for vertical axis Darrieus turbine were analyzed comparatively. From the study it has been found that the models derived from stream tube assumptions can be useful for simple prediction of basic design characteristics of Darrieus turbine. But, for a large tip speed and solidity ratios, the models has shown a certain limit in its applicability according to the formulation scheme applied. The results have shown that for the case having large tip speed and solidity ratios the consideration due to stream conditions, such as trailing vortices or wakes, should be included for accurate prediction of the aerodynamic performances of Darrieus turbine.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.11
• /
• pp.849-854
• /
• 2013

Experimental study was conducted to investigate aerodynamic interference effect of wing tip vortex in formation flight of high speed aircraft. In formation flight, wing tip vortex produced by leading aircraft can affect on the aerodynamic characteristics of trailing aircraft. The interference effect of flow is varied with distances between wing tips of leading and trailing aircraft. It is confirmed, in this study, that the interference of wing tip vortex generated from the leading aircraft makes the aerodynamic forces and moments of the trailing aircraft with the vertical or horizontal positions of the trailing aircraft. Especially, the lift coefficients of trailing aircraft were highly increased at y/b=-0.125, z/b=0.0 or deeply decreased at y/b=-0.5, z/b=0.38. The interfering pattern of wing tip vortices from two aircraft is precisely observed.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.1806-1813
• /
• 2003

The stirred tank reactor is one of the most commonly used devices in industry for achieving mixing and reaction. Here we report on results obtained from the large eddy simulations of flow inside the tank performed using a spectral multi-domain technique. The computations were driven by specifying the impeller-induced flow at the blade tip radius. Stereoscopic PIV measurements (Hill et $al.^{(1)}$) along with the theoretical model of the impeller-induced flow (Yoon et $al.^{(2)}$) were used in defining the impeller-induced flow as superposition of circumferential, jet and tip vortex pair components. Large eddy simulation of flow in a stirred tank was carried out for the three different Reynolds numbers of 4000, 16000 and 64000. The effect of different Reynolds numbers is well observed in both instantaneous and time averaged flow fields. The instantaneous and mean vortex structures are identified by plotting an isosurfaces of swirling strength for all Reynolds numbers. The Reynolds number dependency of the nondimeansional eddy viscosity, resolve scale and subgrid scale dissipations is clearly shown in this study.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.9
• /
• pp.1290-1298
• /
• 2003

The stirred tank reactor is one of the most commonly used devices in industry for achieving mixing and reaction. Here we report on results obtained from the large eddy simulations of flow inside the tank performed using a spectral multi-domain technique. The computations were driven by specifying the impeller-induced flow at the blade tip radius. Stereoscopic PlY measurements (Hill et al. $^{(1)}$) along with the theoretical model of the impeller-induced flow (Yoon et al. $^{(2)}$) were used in defining the impeller-induced flow as superposition of circumferential, jet and tip vortex pair components. Large eddy simulation of flow in a stirred tank was carried out for the three different Reynolds numbers of 4000, 16000 and 64000. The effect of different Reynolds numbers is well observed in both instantaneous and time averaged flow fields. The instantaneous and mean vortex structures are identified by plotting an isosurfaces of swirling strength for all Reynolds numbers. The Reynolds number dependency of the non-dimensional eddy viscosity, resolved scale and subgrid scale dissipations is clearly shown in this study.

• International Journal of Aeronautical and Space Sciences
• /
• v.4 no.1
• /
• pp.88-98
• /
• 2003

Compared to the noise limits (CAN7) specified in ICAO Annex 16 for civil helicopters, the Lynx helicopter equipped with BERP blades has only 0.2 EPNdB margin in the approach case although it has more than 4 EPNdB margin in fly-over and take-off conditions. The objectives of the study described in this paper were to devise a low noise main rotor blade for the Lynx using UEAF combined with the high resolution airload model ACROT. A design requirement is that the new blade, KBERP (Korean BERP) blade should achieve a significant reduction in noise during approach(at least 6EPNdB margin) without any noise penalty in fly-over and take-off conditions and minimal performance penalty. It was decided to investigate a tip modification to the BERP blade, employing the twin vortex concept to reduce the BVI noise and to retain the excellent high speed performance characteristics of BERP. Through the parametric study, the KBERP blade with optimized twin vortices has at least a 9 EPNdB noise margin in approach flight condition with only a small penalty in fly-over and take-off conditions. The KBERP tip is thus a very cost effective wav to reduce BVI noise during approach.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.7
• /
• pp.69-74
• /
• 2003

By employing vane tip concept, a new rotor blade (NRSB-I) has been designed to enhance the noise characteristics of BERP blade. Numerical analyses have been performed for hovering rotor and the results are compared with respect to those of original BERP blade. Although the thrust of designed rotor decreases by 6-7% due to cutout at the tip region, the results indicate that the actual performance loss is negligible because power reduction is greater than thrust loss. It is also found that aerodynamic fence is required at the outboard kink to obtain clearly separated twin-vortices because the vortex generated at kink is diffused during the convection over the blade surface.