• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.32 no.5
• /
• pp.406-415
• /
• 2010

Purpose: The secondary correction of cleft lip nasal deformity still presents a difficult surgical problems. The present study was aimed to investigate the usefulness of Bardach's technique for secondary correction of cleft lip nasal deformity. Materials and Methods: The subjects were eight patients with unilateral and bilateral cleft lip nasal deformity, who had secondary correction by using Bardach's rhinoplasty technique. Age range was from 2 to 21 years and mean age was 10.6 years. There were 3 boys and 5 girls. Six patients had bilateral and two patients had unilateral cleft lip. Facial photographs were taken before and twenty days after the operation. By using Adobe photoshop, the columella height and the nostril width were measured from the facial frontal photograph and Worm's eye view. The degree of improvement was calculated and statistically analyzed. Results: The degree of improvement of the columella length and the nostril width after Bardach's technique was $70.39{\pm}50.14%$ and $-22.93{\pm}0.15%$ respectively. Bardach's technique resulted in projecting the nasal tip, lengthening the columella, medially advancing the alar bases, restructuring the lower lateral cartilages, and changing orientation of the nostrils from horizontal to oblique. The profile view shows projection of the nasal tip, lengthening of the columella, and the change in the nasolabial angle. The scars remained at the philtrum were matter little in compared with improvement of the nasal appearance. Conclusion: These results indicate that Bardach's technique is an useful surgical technique for secondary correction of cleft lip nasal deformity.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.7 no.1
• /
• pp.75-82
• /
• 1987

It is the objective of this study to estimate J-integral by numerical analysis, in which J-integral as aparameters in fracture mechanics can be used to evaluate unstable ductile fracture which is a important problem with respect to structural stability when the scope is beyond small scale yielding criteria. For this, 8-node isoparametric singular element as crack tip element of a cracked material was used to solve plastic blunting phenomenon at crack tip, and crack opening was forced to start when J-value was exceeding fracture toughness $J_{IC}$ of the material. And crack propagation behaviour was treated by using crack opening angle. From this study, it was shown that crack opening, stable propagation and unstable opening point of the cracked material found by using J-value obtained from this study were accord with the other study, so think, J-value obtained from this study can be directly used as a parameter in fracture mechanics to deal with the problem of stable propagation of crack and unstable ductile fracture.

• Journal of Sensor Science and Technology
• /
• v.15 no.3
• /
• pp.186-191
• /
• 2006

In general, Cerenkov light is produced by a charged particle that passes through a medium with a velocity greater than that of visible light. Although the wavelength of Cerenkov light is very broad, the peak is in the almost visible range from 400 to 480 nm. Therefore, it always causes a problem to detect a real light signal that is generated in the scintillator on the fiber-optic sensor tip for dose measurements of high-energy electron beam. The objectives of this study are to measure, characterize and remove Cerenkov light generated in a fiber-optic radiation sensor tip to detect a real light signal from the scintillator. In this study, the intensity of Cerenkov light is measured and characterized as a function of incident angle of electron beam from a LINAC, and as a function of the energy of electron beam. As a measuring device, a photodiode-amplifier system is used, and a subtraction method using a background optical fiber is investigated to remove Cerenkov light.

• Journal of Korean Neurosurgical Society
• /
• v.29 no.11
• /
• pp.1538-1541
• /
• 2000

Apenetrating head injury by an arrow is extremely rare being only two cases reported in the literature. We report a case of 12-year-old boy who presented with an arrow lodged at the posterior fossa through nasal nostril. He was slightly drowsy, but neurologically intact except a sixth nerve palsy in the left eye. Brain CT showed no intracerebral hemorrhage. The arrow was entered through the right nostril and the tip was stucked in the left cere-bello-pontine angle through the sphenoid sinus. We removed the arrow without craniotomy since the tip was verified smooth and no cerebral arteries were in contact with the arrow. The patient recovered well without any significant complications. The sixth nerve palsy resolved completely after six months. The verification of the shape of the offending material, a retrograde removal of the arrow in the direction of its line of trajectory, and an identification of adjacent cerebral arteries seem to be important in the management of this type of injury.

• Journal of ILASS-Korea
• /
• v.13 no.4
• /
• pp.212-219
• /
• 2008

To develop the twin-fluid atomizer having the excellent performance of painting, the spray characteristics of how a wide area can be painted efficiently by one time spraying were studied in this paper. Spray phenomena are affected by the many factors determining the spray field such as the spraying pressure of gas, the spraying pressure and viscosity of liquid paints, the opening duration of needle valve, the design dimension of nozzle, and so on. As the results of experiments, these factors affecting on spray characteristics were suggested as followings; 1) The optimum spraying pressure of gas was $0.015{\sim}0.02\;kPa$, and the appropriate spraying pressure of liquid paint was 0.01kPa, In these situations, the setting up pressures must be compensated as much as the losing amount of pressure because a decompression occurred when operating valves. 2) The duration of opening the needle valve must be sustained for $1{\sim}2$ seconds to inject gas after spraying the liquid paint. This operating of the needle valve was necessary to avoid the affect on the changing of liquid column length, and to prevent the droplet deposit at the initial time of spraying. 3) The spray tip penetration was gained form the experimental equation, and the effective spraying angle was $85^{\circ}{\pm}5^{\circ}$ just at he appropriate spraying pressure of gas. The distribution of the area sprayed had the variation in $350{\pm}50\;mm$ because of the spraying pressure of gas, the its distance from the spray tip, and the lift of the needle valve.

• International Journal of Fluid Machinery and Systems
• /
• v.5 no.2
• /
• pp.65-71
• /
• 2012

The objective of the present investigation is to explore the possibility of improving the performance of a centrifugal fan at low Reynolds numbers using a simple passive means, namely Gurney flap (GF). GFs of 1/$8^{th}$ inch brass angle (3.175 mm) corresponding to 15.9% of blade exit height or 5.1% of blade spacing at the impeller tip are attached to the impeller blade tip on the pressure surface. Performance tests are carried out on the centrifugal fan with vaneless diffuser at five Reynolds numbers (viz., 0.30, 0.41, 0.55, 0.69, $0.82{\times}10^5$, i.e., at five speeds respectively at 1,100, 1,500, 2,000, 2,500 and 3,000 rpm) without and with GF. Static pressures on the vaneless diffuser hub and shroud are also measured for each speed at four flow coefficients [${\phi}$=0.23 (below design flow coefficient), ${\phi}$=0.34 (design flow coefficient), ${\phi}$=0.45 (above design flow coefficient) and ${\phi}$=0.60 (above design flow coefficient)] with and without GF. From the performance curves it is found that the performance of the fan improves considerably with GFs at lower Reynolds numbers and improves marginally at higher Reynolds number. Similar improvements are observed for the static pressures on the diffuser hub and shroud. The effect of Reynolds number on the performance and static pressures is considerable. However the effect is reduced with GFs.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.2
• /
• pp.331-341
• /
• 1993

The propagating crack problems under dynamic antiplane mode in orthotropic material is studied in this paper. To analyze the dynamic fracture problems by theoretical method or experimental method in orthotropic material, it is important to know the dynamic stress intensity factor in the vicinity of crack tip. Therefore the dynamic stress field and dynamic displacement field with dynamic stress intensity factor of orthotropic material in mode III were derived. When the crack propagation speed approachs to zero, the dynamic stress components and dynamic displacement components derived in this paper are identical to the those of static state. In addition, the relationships between dynamic stress intensity factor and dynamic energy release rate are determined by using the concept of crack closure energy with the dynamic stresses and dynamic displacements derived in this paper. Finally, the characteristics of crack propagation are studied with the properties of orthotropic material and crack speed. The variation of angle .alpha. between fiber direction and crack propagating direction and crack propagation speed fairly effect on stress component and displacement component in crack tip. The influence of crack propagation speed on the speed on the stress and displacement is greater in the case of .alpha.=90.deg. than in the case of .alpha.=0.deg. and the faster the crack propagation speed, the greater the stress value and displacement value.

• Journal of Advanced Marine Engineering and Technology
• /
• v.30 no.3
• /
• pp.351-358
• /
• 2006

The capability of high pressure injection with small fuel quantify at all engine operating conditions is one of the main feature in common rail fuel injection system, which is used in small and light-duty Diesel engine. The key parameter for the better atomized fuel sprays and multiple injections of this common rail fuel injection control, that can be freely selected irrespective of the engine speed and load is the mechanism controlling the needle energizing and movement in high pressure Diesel injector. In the electro-hydraulic injector, the injection nozzle is being opened and closed by movement of the injector's needle which is balanced by pressure between the nozzle seat and the needle control chamber. This study describes the macroscopic spray structure characteristics of the common rail Diesel injectors with different electric driving method i.e. the solenoid-driven and piezo-driven type. The macroscopic spray characteristics such as spray tip speed. spray tip penetration and spray cone angle were investigated by the high speed spray, which is measured by the back diffusion light illumination method with optical system for the high speed temporal photography in a constant volume chamber pressurized by nitrogen gas. As the results, the prototype piezo-driven injector system was designed and fabricated for the first time in domestic case and the effect of injector's needle response driven by different drive type was compared between the solenoid and piezo-driven injector It was found therefore. that the piezo-driven injector showed faster needle response and had better needle control capability by altering the electric input value than the solenoid-driven injector.

• Archives of Plastic Surgery
• /
• v.32 no.3
• /
• pp.287-292
• /
• 2005

The definitive correction of secondary lip nasal deformities is a great challenge for plastic surgeons. To rectify the secondary lip nasal deformities, various procedures and its modifications have been reported in many centers. However, no universal agreement exist to correct the various components of secondary nasal deformities. The secondary nasal deformity of the unilateral cleft lip has its own characteristic abnormalities including the retroplaced dome of the ipsilateral nasal tip, hooding of the alar rim, a secondary alar-columellar web, short columella, depressed alar base and so forth. Among these components of secondary nasal deformity, maxillary hypoplasia, especially in the area of piriform aperture, and alveolar bone defect can make the alar base depressed, which in turn, leads to wide and flat nasal profile, obtuse nasolabial angle coupled with subnormal nasal tip projection in aspect of aesthetic consideration. Moreover, the maxillary hypoplasia contributes to reduced size of the nasal airway in combination with other component of external nasal deformity and therefore the nasal obstruction may be developed functionally. Therefore, the current authors have performed corrective rhinoplasty with the augmentation of alar base with various methods which include rearrangement of soft tissue, vertical scar tissue flap and use of allogenic or autologous materials in 42 patients between 1998 and 2003. The symmetric alar base could be achieved, which provides the more accurate evaluation and more appropriate management of the various component of any coexisting secondary nasal deformity. In conclusion, the augmentation of alar base, as a single procedure, is a basic and essential to correct the secondary lip nasal deformities.

• The korean journal of orthodontics
• /
• v.44 no.2
• /
• pp.77-87
• /
• 2014

Objectives: This study was designed to define the Korean norm values for the Ricketts analysis. Methods: In this longitudinal study, lateral cephalograms of 31 subjects with normal occlusion were taken biennially from ages 9-19 years. Cephalometric measurements were performed. Parameters for which the 10-year change did not exceed one standard deviation were defined as unchanged. The means and standard deviations for the measured parameters were determined for each age group. Results: No significant changes in growth were observed in the molar relationship, incisor overjet, incisor overbite, mandibular incisor extrusion, interincisor angle, lower incisor tip (B1) to A point-Pogonion (A-PO) plane, upper incisor tip (A1) to A-PO plane, B1 inclination to A-PO, A1 inclination to A-PO, B1 inclination to Frankfurt plane (FH), convexity, lower facial height, facial axis, maxillary depth, maxillary height, palatal plane to FH, cranial deflection, ramus Xi position, or porion location. Continual changes over the 10 years of growth were observed in the maxillary first molar distal position to pterygoid true vertical plane, facial depth, mandibular plane to FH, anterior cranial length, mandibular arc, and corpus length. Conclusions: Clinicians can apply the Korean norms at age 9 as determined in this study when using the Ricketts analysis. The patient's age at the beginning of treatment and their sex should be taken into consideration when drawing visual treatment objectives.