• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1990.10a
• /
• pp.39-44
• /
• 1990

Polycrystalline CdS films were grown on glass substrate with conducting indium tin oxide(ITO) by electrodeposition. The average size of the plate-shape grains o the CdS films was from 0.3um to 0.05um, and the adhesion to ITO was excellent. The optical band gap of the electrodeposited CdS films was in the range from 2.51eV to 2.68 eV. The optical transmittance was 80% and the electrical resistivity varied from 10$^3$ to 10$\^$5/$\Omega$-cm depending on the deposition condition.

• Restorative Dentistry and Endodontics
• /
• v.18 no.2
• /
• pp.431-445
• /
• 1993

The purpose of this study was to observe corrosion characteristics of six dental amalgams and was to analyse corrosion products electrochemically. After each amalgam alloy and Hg was triturated as the direction of the manufacturer by using mechanical amalgamator, the triturated mass was inserted into the cylinderical metal mold ($12{\times}10mm$) and was condensed with 160kg/$cm^2$ by using the hydrolic press. The specimen was removed from the mold and was stored at room temperature for 1 week, and was polished with amalgam polishing kit. The anodic and cathodic polarization curve was obtained by using cyclic voltammetric method with 3-electrode potentiostat in saline for each amalgam and Ag, Sn, Cu plate specimen at $37{\pm}0.5^{\circ}C$. The potential sweep range was -1.7V~0. 4V(vs SCE) in working electrode and scan rate was 50mV/s and the exposed surface area of each specimen to the electrolytic solution was $0.79cm^2$. The results were as follows. 1. In anodic-cathodic polarization curve of amalgam specimens, two anodic current rising areas and two cathodic current peaks were obtained at the low Cu amalgam(CF, CS) specimen and three anodic current rising areas and three cathodic current peaks were obtained at the high Cu amalgam (TY, DS, HV) specimen. 2. As this compared with the anodic and cathodic current peak potentials of Sn, Cu and Ag specimen, the first cathodic current peak I c was caused by the reduction of divalent tin salt, second cathodic current peak IIIc results from the reduction of quadravalent tin salt, and third cathodic current peak me results from the reduction of copper salt. 3. As reverse potential sweeping was done repeatedly, anodic current was decreased slightly in all amalgam specimens.

• Korean Journal of Heritage: History & Science
• /
• v.47 no.4
• /
• pp.224-243
• /
• 2014

This study examined the materials and casting technology(cast, alloy, etc.) used in the manufacturing of bronze artifacts based on old literature such as Yongjae Chonghwa, Cheongong Geamul, and The Korea Review. In the casting experiment for restoration of Sangpyong Tongbo, a bronze and brass mother coin mold was made using the sand mold casting method described in The Korea Review. The cast was comprised of the original mold plate frame, wooden frame, and molding sand. Depending on the material of the outer frame, which contains the molding sand, the original mold plate frame can be either a wooden frame or steel frame. For the molding sand, light yellow-colored sand of the Jeonbuk Iri region was used. Next, the composition of the mother alloy used in the restoration of Sangpyong Tongbo was studied. In consideration of the evaporation of tin and lead during actual restoration, the composition of Cu 60%, Zn 30%, and Pb 10% for brass as stated in The Korea Review was modified to Cu 60%, Zn 35%, and Pb 15%. For bronze, based on the composition of Cu 80%, Sn 6%, and Pb 14% used for Haedong Tongbo, the composition was set as Cu 80%, Sn 11%, and Pb 19%. The mother coin mold was restored by first creating a wooden father coin, making a cast from the wooden frame and basic steel frame, alloying, casting, and making a mother coin. Component analysis was conducted on the mother alloy of the restored Sangpyong Tongbo, and its primary and secondary casts. The bronze mother alloy saw a 5% increase in copper and 4% reduction in lead. The brass parent alloy had a 5% increase in copper, but a 4% and 12% decrease in lead and tin respectively. Analysis of the primary and secondary mother coin molds using an energy dispersive spectrometer showed that the bronze mother coin mold had a reduced amount of lead, while the brass mother coin mold had less tin. This can be explained by the evaporation of lead and tin in the melting of the primary mother coin mold. In addition, the ${\alpha}$-phase and lead particles were found in the mother alloy of bronze and brass, as well as the microstructure of the primary and secondary coin molds. Impurities such as Al and Si were observed only in the brass mother coin mold.

• Journal of Broadcast Engineering
• /
• v.9 no.4 s.25
• /
• pp.424-433
• /
• 2004

Jing(gong) is one of the most well known Korean traditional Samulnori instruments to the general public. Samulnori is consisted of four instruments, them being : the jingo the janggu (hour-glass drum). the kkwaenggwari, and the buk(drum). Of the four instruments, the jing with its deep, and yet soft and beautiful long lingering sound embraces the sounds of the other three. The jing is a brassware instrument, a compound of $70{\%}\;copper\;and\;22{\%}\;tin.$\;A high quality brassware is used when the jing is made. The jing is shaped with a 39-40cm circular plate and a rim that gives 7.0-7.5cm of depth to the instrument. Even with its most simple structure, when the circular plate is hit during performance, the rim which supports the circular plate gives resonance to the sound making low-frequency sounds. Therefore the range of the representative frequency of the full rim jing is between $118.4{\~}366.0[Hz],$\;the lingering sound lasts for more than 20 seconds afterwards. When the jing with half of its rim cut off is hit the basic frequency is $139.9{\~}387.5[Hz].$\;And the sound lasted for ten more seconds. The jing of its rimless frequencies are distributed between $990.5{\~}1,372[Hz].$\;And the lingering sound lasts for 5seconds afterwards. Therefore, different thickness and depth of the rim may give new resonance frequencies and alter the longing time of the sound. This thesis paper will try to reveal the relationship between the thickness or depth of the rim (which holds the bending circular plate) and the frequency or the lasting time of the sound.

• Journal of the Korean Applied Science and Technology
• /
• v.19 no.1
• /
• pp.43-48
• /
• 2002

We carried out this subject to observe photoisomerization using 1,2-dioleoyl-sn- glycero-3-phosphocholine(DOPC) mixed with fatty acid containing azobenzene group which has reversible to cis-trans by light irradiation. Spreading solutions for the LB films were prepared in chloroform($5.0{\times}10^{-5}$mol/L).We investigated the photoisomerization and property of the organic ultra thin film of fatty acid containing azobenzene was prepared on the hydrophilic ITO(idium tin oxide) glass plate by LB method. As a result, the absorption spectra of 8A5H and DOPC of mixture LB films was induced to photoisomerization by alternating irradiation of ultraviolet and visible light, because the condensation of pure azobenzene monolayers was loosened by the introduction of phospholipid into the monolayers, and the molecular high aggregation in pure azobenzene monolayers is also weakened by the introduction of phospholipid. We found that it was reversibly induced to cis-trans photoisomerization in several solvents and mixture LB films.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.61.1-61.1
• /
• 2011

본 연구에서는 Zinc Tin Oxide (ZTO)/Ag/ZTO 다층 투명 전극을 제작하고 이를 비정질 ZTO (a-ZTO) 채널을 기반으로 한 TFT에 적용하여 투명 TFT의 전기적 특성을 확인하였다. 15${\times}$15 mm 크기의 ITO (gate)/Glass 기판상에 ALD법으로 투명 $Al_2O_3$절연층을 형성하고, RF sputtering법으로 50nm 두께의 a-ZTO 채널층을 형성하였다. 열처리를 위하여 Hot plate를 이용해 대기 중에서 $300^{\circ}C$의 온도로 20분간 열처리하여 채널 특성을 최적화 하였다. 이후 투명 Source/Drain으로 ZTO/Ag/ZTO 다층 투명 전극을 DC/RF sputtering법으로 패터닝하여 투명 TFT를 완성하였고, 평가를 위해 금속 (Mo)을 Source/Drain으로 사용한 TFT를 제작하여 그 성능을 비교하였다. ZTO/Ag/ZTO 다층 투명 전극은 Ag의 삽입으로 인하여 3.96ohm/square의 매우 낮은 면저항과 $3.24{\times}10-5ohm-cm$의 비저항을 나타내었으며, Antireflection 효과에 의해 가시광선 영역 (400~600 nm)에서 86.29%의 투과율을 나타내었다. ZTO/Ag/ZTO 다층 투명 전극 기반 투명 TFT는 $6.80cm^2/V-s$의 이동도와 $8.2{\times}10^6$의 $I_{ON}/I_{OFF}$비를 나타내어 금속 Source/Drain 전극에 준하는 특성을 나타내었다. 뿐만 아니라 전체 소자의 투과도 또한 ~73.26% 수준을 나타내어 투명 TFT용 Source/Drain 전극으로서 ZTO/Ag/ZTO 다층 투명 전극의 가능성을 확인하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.874-877
• /
• 2004

We carried out this subject to observe electrochemical properties of 1,2-dioleoyl-sn- glycero-3-phosphocholine(DOPC) mixed with fatty acid containing azobenzene group by using cyclic voltammetry with a three-electrode system, An Ag/AgCl reference electrode, a platinum wire counter electrode and LB film-coated ITO working electrode in $NaClO_4$ solution. We investigated the photoisomerization and electrochemical property of the organic ultra thin film of fatty acid containing azobenzene was prepared on the hydrophilic ITO(idium tin oxide) glass plate by LB method. As a result, the absorption spectra of BASH and DOPC of mixture LB films was induced to photoisomerization by alternating irradiation of ultraviolet and visible light. A measuring range was reduced from initial potential to -1350mV, continuously oxidized to 1650 mV and measured to the initial point. The scan rate were 50, 100, 150 and 200 mV/s. As a results, LB films of BASH-DMPC appeared reversible process caused by the reduction-oxidation current from the cyclic voltammogram.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.5
• /
• pp.541-544
• /
• 2004

Multi- wall carbon nanotubes(MWNTs) were synthesized by thermal chemical vapor deposition. The paste for screen printing was composed of MWNTs, organic vehicle and glass frit. Carton nanotube paste was screen-printed on ITO(indium tin oxide) deposited soda lim을 glass, and then heat treatment was performed. Before the surface treatment, turn on field of derive was 2.6 V/$\mu\textrm{m}$. After the surface treatment, the value was changed into 1.8 V/$\mu\textrm{m}$. The anode current of the derive with 2.83 V/$\mu\textrm{m}$(turn on field) was changed 4 $\mu\textrm{A}$ into 390 $\mu\textrm{A}$ at 1,700 V. Adsorption effect of MWNTs onto phosphor of anode plate was observed by the field emission measurement and resulted in bad effects on properties of devices lifetime and emission lighting.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.05a
• /
• pp.31.1-31.1
• /
• 2009

Carbon nanotubes (CNTs) are attractive material because of their superior electrical, mechanical, and chemical properties. Furthermore, their geometric features such as a large aspect ratio and a small radius of curvature at tip make them ideal for low-voltage field emission devices including backlight units of liquid crystal display, lighting lamps, X-ray source, microwave amplifiers, electron microscopes, etc. In field emission devices for display applications, the phosphor anode is positioned against the CNT emitters. In most case, light generated from the phosphor by electron bombardment passes through the anode front plate to reach observers. However, light is produced in a narrow depth of the surface of the phosphor layer because phosphor particles are big as much as several micrometers, which means that it is necessary to transmit through the phosphor layer. Hence, a drop of light intensity is unavoidable during this process. In this study, we fabricated a transparent cathode back plate by depositing an ultra-thin film of single walled CNTs (SWCNTs) on an indium tin oxide (ITO)-coated glass substrate. Two types of phosphor anode plates were employed to our transparent cathode back plate: One is an ITO glass substrate with a phosphor layer and the other is a Cr-coated glass substrate with phosphor layer. For the former case, light was radiated from both the front and the back sides, where luminance on the back was ~30% higher than that on the front in our experiments. For the other case, however, light was emitted only from the cathode back side as the Cr layer on the anode glass rolled as a reflecting mirror, improving the light luminance as much as ~60% compared with that on the front of one. This study seems to be discussed about the morphologies and field emission characteristics of CNT emitters according to the experimental parameters in fabricating the lamps emitting light on the both sides or only on the cathode back side. The experimental procedures are as follows. First, a CNT aqueous solution was prepared by ultrasonically dispersing purified SWCNTs in deionized water with sodium dodecyl sulfate (SDS). A milliliter or even several tens of micro-liters of CNT solution was deposited onto a porous alumina membrane through vacuum filtration. Thereafter, the alumina membrane was solvated with the 3 M NaOH solution and the floating CNT film was easily transferred to an ITO glass substrate. It is required for CNT film to make standing CNTs up to serve as electron emitter through an adhesive roller activation.

• Journal of Adhesion and Interface
• /
• v.10 no.2
• /
• pp.77-83
• /
• 2009

PDMS was selected for a coating material of implantable biosensors and the cytotoxicity of extracts released from a polymer was evaluated using ISO 10993-5, Biological evaluation of medical devices-Part 5: Tests for in vitro cytotoxicity. Organo-tin was used as a positive control and a medium without serum was used as a negative control. Materials extract were prepared by incubating specimens in RPMI medium without serum ($125{\mu}L/cm^2$) for 24 h, 1 week and 6 weeks at $38^{\circ}C$. The evaluation of cytotoxicity was performed by two different methods : 1) seeding cells with extracts at the beginning 2) incubating extracts with cell sheets already formed on the plate. Both cell morphology and MTT numerical data were shown for the confirmation of cytotoxicity and cell spreading on the surface of PDMS.