• Journal of Mechanical Science and Technology
• /
• v.17 no.2
• /
• pp.197-206
• /
• 2003

It is intended to retrieve the time history of displacement from measured acceleration signal. In this study, the word retrieving means reconstructing the time history of original displacement signal from already measured acceleration signal not just extracting various information using relevant signal processing techniques. Unlike extracting required information from the signal, there are not many options to apply to retrieve the time history of displacement signal, once the acceleration signal is measured and recorded with given sampling rate. There are two methods, in general, to convert measured acceleration signal into displacement signal. One is directly integrating the acceleration signal in time domain. The other is dividing the Fourier transformed acceleration signal by the scale factor of - $\omega$$^2$and taking the inverse Fourier transform of it. It turned out both the methods produced a significant amount of errors depending on the sampling resolution in time and frequency domain when digitizing the acceleration signals. A simple and effective way to convert the time history of acceleration signal into the time history of displacement signal without significant errors is studied here with the analysis on the errors involved in the conversion process.

• Proceedings of the KOSOMBE Conference
• /
• v.1994 no.12
• /
• pp.113-116
• /
• 1994

Estimation of the evoked potential using the iterated bispectrum and cross-correlation (IBC) has been tried for both simulation and real clinical data. Conventional time average (TA) method suffers from synchronization error when the latency time of the evoked potential is random, which results in poor SNR distortion in the estimation of EP waveform. Instead of EP signal average in time domain, bispectrum is used which is insensitive to time delay. The EP signal is recovered by the inverse transform of the Fourier amplitude and phase obtained from the bispectrum. The distribution of the latency time is calculated using cross-correlation between EP signal estimated by the bispectrum and the acquired signal. For the simulation. EEG noise was added to the known EP signal and the EP signal was estimated by both the conventional technique and bispectrum technique. The proposed bispectrum technique estimates EP signal more accurately than the conventional technique with respect to the maximum amplitude of a signal, full width at half maximum(FWHM). signal-to-noise-ratio, and the position of maximum peak. When applied to the real visual evoked potential(VEP) signal. bispectrum technique was able to estimate EP signal more distinctively. The distribution of the latency time may play an important role in medical diagonosis.

• Journal of Navigation and Port Research
• /
• v.29 no.4
• /
• pp.341-347
• /
• 2005

A unique technique to extract the phase in time domain is proposed in order to measure the time parameters such as speed and depth by transmitting sound and electric waves. In the signal analysis processing, the phase of pulse signal can be transformed and digitalized with local data in real time without the effect of direct current bias and Nyquist limits. This method is sensitive to base frequency of pulse signal with high spacial resolution and is effective to compare two signals which have different forms. It is expected that the phase analysis technique will be applied to the measurement of the speed and depth accurately by ultrasonic pulse signal in water.

• Journal of the Ergonomics Society of Korea
• /
• v.36 no.5
• /
• pp.459-466
• /
• 2017

Objective: This study examined two traffic signals with a countdown indicator in terms of driver's reaction time and subjective satisfaction score and their performance was compared with a standard traffic signal in driving simulation. Background: Dilemma zone is created when a traffic light changes at intersections. It often pushes drivers to rush in urgent and premature decision making whether to go or stop and thus induces unnecessary mental load among drivers, which may lead to sudden conflicts with following vehicles at intersections. Method: Forty college students (male: 20, female: 20) participated in this driving simulation study. Three traffic signals were employed: (1) standard traffic signal; (2) countdown-separated signal; and (3) countdown-overlaid signal. The countdown-separated and countdown-overlaid signals were designed to inform drivers of the remaining time of a green light before tuning to an amber light. Reaction times (sec) and satisfaction scores (7-point scale) for the two signals with a countdown indicator were compared with those for the standard traffic signal. Results: Reaction times of the countdown-separated (0.49 sec) and countdown-overlaid (0.43 sec) signals were significantly shorter than that of the standard signal (0.67 sec). Satisfaction scores of the countdown-separated (5.3 point) and countdown-overlaid (5.6 point) signals were greater than that of the standard signal (3.8 point). Lastly, the countdown-overlaid signal showed better performance than the countdown-separated signal, but their differences in reaction time (0.06 sec) and satisfaction score (0.3 point) were small. Conclusion: Traffic signals with a countdown indicator can improve drivers' reaction time and satisfaction score than the standard traffic signal. Application: Traffic signals with a countdown indicator will be useful for reducing the length of dilemma zone at intersections, by allowing drivers to predict the remaining time of a green light.

• 전기의세계
• /
• v.18 no.1
• /
• pp.15-23
• /
• 1969

A lot of recent researches have shown that a Pseudo Random Binary Signal is a quite effective test signal to measure the impulse response of a plant. Generally speaking, however, such a response itself is not satisfactory to determine the appropriate control parameters or control inputs. Here, the author intends to estimate the unknown parameters of the First Order Plant with Dead Time by means of correlation method using M-sequence signal. The time constant T and the dead time L of the plant are eatimated with one tracking loop by automatically adjusting delay time .tau. of M-sequence signal according to variations of T and L. In this paper, a three level M-sequence signal is used as a test signal in order to avoid troublesome operations to calculate partial derivatives of a given performance index with respect to the parameters which are usually required in the Model Method. Several experiments with analogue computer using low pass filters as averaging circuits showed good results as expected.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.2
• /
• pp.268-275
• /
• 2008

In this paper, we introduce a new method for detecting and estimating faults on a power line using the time-frequency domain reflectometry system. The system rests upon time-frequency signal analysis and uses a chirp signal which is multiplied by Gaussian envelope. The chirp signal is used as a reference signal, and we can get the reflected signal from a fault on a wire. To detect and estimate faults, we analyze the reflected signal by Wigner time-frequency distribution function and normalized time-frequency cross correlation function. In this paper we design an optimal reference signal for power line and implement a system for estimating fault distance on a power line with the TFDR implemented by PXI equipments. This approach is verified by some experiments with HIV 2.25mm power lines.

• International Journal of Fuzzy Logic and Intelligent Systems
• /
• v.5 no.4
• /
• pp.360-366
• /
• 2005

In the past, when there were few vehicles on the road, the T.O.D.(Time of Day) traffic signal worked very well. The T.O.D. signal operates on a preset signal cycling which cycles on the basis of the average number of average passenger cars in the memory device of an electric signal unit. Now days, with increasing many vehicles on restricted roads, the conventional traffic light creates startup-delay time and end-lag-time. The conventional traffic light loses the function of optimal cycle. And so, $30-45\%$ of conventional traffic cycle is not matched to the present traffic cycle. In this paper we proposes electro sensitive traffic light using fuzzy look up table method which will reduce the average vehicle waiting time and improve average vehicle speed. Computer simulation results prove that reducing the average vehicle waiting time which proposed considering passing vehicle length for optimal traffic cycle is better than fixed signal method which doesn't consider vehicle length.

• Journal of Institute of Control, Robotics and Systems
• /
• v.4 no.2
• /
• pp.246-255
• /
• 1998

This paper presents a novel method for real-time malfunction detection of plasma etching process using EPD signal traces. First, many reference EPD signal traces are collected using monochromator and data acquisition system in normal etching processes. Critical points are defined by applying differentiation and zero-crossing method to the collected reference signal traces. Critical parameters such as intensity, slope, time, peak, overshoot, etc., determined by critical points, and frame attributes transformed signal-to symbol of reference signal traces are saved. Also, UCL(Upper Control Limit) and LCL(Lower Control Limit) are obtained by mean and standard deviation of critical parameters. Then, test EPD signal traces are collected in the actual processes, and frame attributes and critical parameters are obtained using the above mentioned method. Process malfunctions are detected in real-time by applying SPC(Statistical Process Control) method to critical parameters. the Real-time malfunction detection method presented in this paper was applied to actual processes and the results indicated that it was proved to be able to supplement disadvantages of existing quality control check inspecting or testing random-selected devices and detect process malfunctions correctly in real-time.

• Proceedings of the KIEE Conference
• /
• 2006.07d
• /
• pp.1803-1804
• /
• 2006

The purpose of this paper is to implement a Labview based TFDR Real Time system through the instruments of Pci eXtensions for Instrumentation(PXI). The proposed load impedance measurement algorithm was verified by experiments via the implemented real time system. The TFDR real time system consisted of the reference signal design, signal generation, signal acquisition, algorithm execution and results display parts. To implement real time system, all of the parts wore programmed by the Labview which is one of graphical programming languages. In the application software implemented by the Labview we were able to design a suitable reference signal according to the length and frequency attenuation characteristics of the target cable and controled the arbitrary waveform generator(ZT500PXI) of the signal generation part and the digital storage oscilloscope(ZT430PXI) of the signal acquisition part. By using the TFDR real time system with the terminal resistor on the target cable, we applied to the load impedance measurements. In the proposed load impedance algorithm a normalized time-frequency cross correlation function and a cross time-frequency distribution function was employed to calculate the reflection coefficient and phase difference between the input and the reflected signals.

• Journal of the Semiconductor & Display Technology
• /
• v.18 no.1
• /
• pp.59-64
• /
• 2019

Recently, time synchronous has become important for satellite launch control facilities, multiple thermal power plants, and power system facilities. Information from time synchronous at each of these industrial sites requires time synchronization to control or monitor the system with correlation. In this paper, IRIG-B codes, which can be used for time synchronous, are used as specifications in IRIG standard 200-16. Signals from IRIG-B120 (Analog), IRIG-B000 (Digital), and one PPS are output from GPS receiver. Using the signal from IRIG-B120 (Analog), it passes through the signal from the analog amplifier and generates one PPS signal using the field-programmable gate array. The FPGA is used cyclone EPM570T100I5N. According to IEEE regulations, the error of one PPS is specified within 1us, but in this paper, the error is within 100ns. The output of the one PPS signal was then compared and tested against the one PPS signal on the GPS receiver to verify accuracy and reliability. In addition, the proposed time synchronous is simple to construct and structure, easy to implement, and provides high time precision compared to typical time synchronous. The output of the one PPS signals and IRIG-B000 signal will be used in many industry sectors.