• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.05a
• /
• pp.731-736
• /
• 2001

In this thesis, the study on controlling of cracks of concrete box culvert in early ages is presented. The optimum construction method and economical analysis were proposed also through the experiment of the material and field test. As a result of the experiment of the material, using fly ash, CSA expansive agent and BELITE cement(type IV) showed good result in the control of cracks induced by heat of hydration and shrinkage. As a result of construction test analysis, the maintenance time of form system did not show a big difference in controlling of cracks. Control of distribution of reinforcement, spacing of expansion joint and use of BELITE cement showed big differences in the control of cracks in early ages. As a result of economical analysis, control of construction variables before construction can make it possible to reduce the repair expense.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.04a
• /
• pp.57-58
• /
• 2008

Microcrystalline (${\mu}c$) silicon thin films were prepared on glass by plasma-enhanced-chemical-vapor-deposition (PECVD) at various substrate temperature, and dilution ratio of $H_2$ with $SiH_4$. The structural and optical properties of. the ${\mu}c-Si$ thin films were investigated using XRD and UV-VIS spectrophotometer. The ${\mu}c-Si$ thin film with 42 nm grain size was grown at optimal condition of 2.5 Torr, spacing between electrodes of 3cm, deposition time of 3000s, RF power of 200W, substrate temperature of $350^{\circ}C$, $SiH_4$ ($20%SiH_4$+80%He) of 50sccm, and $H_2$ of 100sccm.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2000.10a
• /
• pp.568-572
• /
• 2000

This paper describes the experimental results of a transient impedance characteristics of grounding rods to a square pulse and standard lightning impulse current. The test were performed on single grounding rod($\phi$ 10mm, 1m) and triple-grounding rods( $\phi$ 10mm, 1m) of equilateral triangles with 5m spacing. For measurements of transient impedance, a pulse generator which can produce square wave of 30ns rise time and 20U Pulse duration was designed and fabricated. In the experiment, transient impedance of the grounding systems have been investigated from the recorded potential and current waveforms. The results showed that the value of the transient impedance is quite higher than the stationary resistance, and provide useful information for the value of a grounding system considered transient characteristics under a high frequency condition such as lightning stokes and ground-fault.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.05a
• /
• pp.330-333
• /
• 2006

In this paper experimental tests were performed to evaluate velocities of the acoustic waves through prestressed concrete beam and source locations using AE technique. Seven AE sensors are mounted on the surface of 5m length test beam with equal spacing and using Schmidt Hammer AE events are made 18 locations. The velocities of AE signals are evaluated using the time differences of arrival times and the distances between the AE source loactions and the AE sensor locations. In addition, using the Least Square Method, the AE source locations are re-evaluated reversely using both of the arrival times and the velocities of AE signals. Test results show the average velocity of the AE signals is about 4,000m/sec and the velocity decreased with the increase of the trevalling times due to the effect of attenuation. Based on the estimation of the source locations, it is observed that the accuracy of source location is increased when the velocity of each AE sensor used rather than the average velocity.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.05b
• /
• pp.21-24
• /
• 2006

An experimental investigation was earned out to evaluate the fire performance of high strength concrete column made with different section size. Two different high strength concrete columns measuring 3,428mm in height and with the same tie spacing of 150mm were prepared to evaluate the effect of section size of $305{\times}305mm$ and $500{\times}500mm$ on the fire resistance. Compressive strength was 138MPa at the time of fire resistance fire testing. Based on the test result, fire resistance of column with the larger section of $500{\times}500mm$ exhibited the better performance than that of the smaller section of $305{\times}305mm$. The former withstood against the very high temperature over 240minutes, while the latter resisted during 176minutes.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.5
• /
• pp.61-66
• /
• 1997

In this paper we report the fabrication of an InGaAs metal-semiconductor-metal (MSM) photodiode(PD) which an InAlAs barrier enhancement layer that has very low dark current and high speed chracteristics. The detector using Cr/Au schottky metal fingers with 4um spacing on a large active area of 300*300um$^{2}$ offers a low dark current of 38nA at 10V, a low capacitance of 0.8pF, and a high 3-dB bandwidth of 2.4 GHz. To our knowledge, these characteristics are better than any previously published results obtained from large area InGaAs MSM PD's. The RC equivalent model and frequency domain current response model considering transit time were also used to analyze the frequency characteristic of the fabricated device.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2006.03a
• /
• pp.1148-1154
• /
• 2006

Composite discharge capacity tests and smear effect tests are carried out to estimate the parameters for the reliability-based design of vertical drain method. Also the probabilistic and deterministic solutions of radial consolidation theory are presented. It compared to the result of reliability-based design and that of deterministic design using the tested and estimated parameters. The results indicated that the drain spacing is larger the deterministic method than the probabilistic method because the former is not considered the uncertainties in the properties of soil. The divergence of methods is dependent on the probability of achieving target degree of consolidation by a given time and the coefficient of variation(COV) of the coefficient of horizontal consolidation$(c_h)$.

• 유체기계공업학회:학술대회논문집
• /
• 2000.12a
• /
• pp.65-74
• /
• 2000

A five path ultrasonic and/or magnetic flowmeter were installed after valve. Five path ultrasonic flowmeter were tested to obtain it's performance in a water flow standard system and magnetic flowmeter. It's varied with straight pipe length(nD), install direction and valve position. All the results are summerized. The multi-path flowmeters(MUF) showed up to $\pm0.5{\%}$ at a 2, 4, 8, 15D spacing : the MUF was significantly better than magnetic flowmeter at disturbed flow conditions.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.29A no.2
• /
• pp.77-79
• /
• 1992

We propose a self-aligned and double recessed technique for GaAs power MESFETs application. The gate length and the wide recess width are defined by a selective removal of the SiN layer using reactive ion etching(RIE) while the depth of the channel is defined by chemical etching of GaAs layers. The threshold voltages and the saturation drain voltage could be sucessfully controlled using this technique. The lateral-etched distance increases with the dry etching time and the source-drain breakdown voltage of MESFET increases up to about 30V at a pinch-off condition. The electrical characteristics of a MESFET with a gate length of 2 x10S0-6Tm and a source-gate spacing of 33 x10S0-6Tm show maximum transconductance of 120 mS/mm and saturation drain current density of 170-190mA/mm at a gate voltage of 0.8V.

• ETRI Journal
• /
• v.24 no.5
• /
• pp.341-348
• /
• 2002

We propose an asymmetric sampled grating laser and a multi-wavelength laser array associated with it. Asymmetric sampling periods combined with an index shifter make it possible to use first order reflection for lasing operations. With the structure of our design, we achieved a simple fabrication procedure as well as a high yield without using complex and time-consuming e-beam lithography for multi-period gratings. We analyzed the effect of mirror coating by numerical analysis to improve single mode and power extraction performance. By using high reflection-antireflection coatings, we obtained high power extraction efficiency without degradation of the single mode property. For the multi-wavelength laser array, to gain wavelength control, we varied the sampling periods from one laser to an adjacent laser across the array. With this approach, we showed the feasibility of an array of up to 30 channels with 100 GHz wavelength spacing.