• 대한의용생체공학회:의공학회지
• /
• 제6권2호
• /
• pp.1-8
• /
• 1985

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70$\pm$1.32mmHg/min)compared to CF dialyzers(4.32$\pm$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500, 550, 570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500, 550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100, 300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3, 000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.SpO2 with Plethysmograph.

• 한국우주과학회:학술대회논문집(한국우주과학회보)
• /
• 한국우주과학회 1993년도 한국우주과학회보 제2권2호
• /
• pp.17-17
• /
• 1993

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70${\pm}$1.32mmHg/min)compared to CF dialyzers(4.32${\pm}$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500,550,570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500,550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100,300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3,000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.

• 마케팅과학연구
• /
• 제19권4호
• /
• pp.1-10
• /
• 2009

本研究的目的是对咖啡店的 "重要性"（顾客在光顾咖啡店以前的感知）和积极或消极的 "满意度"（顾客在光顾咖啡店以后的感受）之间的差距进行分类, 并分析这些差距对对购买行为的影响. 为此, 我使用重要性和满意度之间的差距作为选择咖啡店的解释变量, 并通过使用有序Probit模型（OPM）来实证分析差距对购买行为（整体满意度和愿意到再次光顾）的影响方向和大小. 先前使用IPA的研究评估了差距影响的方向和大小的象限, 但是在分析差距对顾客的影响方面却失败了. 在本研究中, 我评估了积极和消极的差距对顾客满意度和愿意去再光顾的影响. 通过使用OPM,我量化了积极和消极的差距对顾客整体满意度和愿意去再光顾的影响. 每个人的支出, 光顾的频率和购买咖啡的地方对顾客整体满意度有最积极的影响. 光顾的频率, 在每人的支出之后, 然后是购买咖啡的地方对顾客整体满意度有最积极的影响. 因此每个人的支出和光顾的频率对顾客整体满意度有最积极的影响. 这一发现意味着一个在咖啡店每次或每周花费5000韩元的顾客的实际的满意度越高（差距), 其整体满意度和愿意去再光顾就越高. 虽然经济效益对总体满意度和愿意去再光顾有显著影响, 但是大专和大学的学生仍然愿意去咖啡馆并愿意消费5000韩元, 因为他们不只是购买咖啡本身而且将咖啡店作为其他活动的场所, 例如工作, 和朋友见面或是放松的地方. 学院和大学的学生还可以在咖啡店通过个人电脑上网, 看电影, 学习, 因此, 咖啡馆应对顾客提供适当的设施和服务. 咖啡店品牌的积极差距对愿意去再光顾有积极的影响表明顾客满意度越高, 顾客越愿意去再光顾. 另一方面, 这一因素的消极差距意味着顾客满意度越低, 顾客再光顾的意愿也越低. 因此, 在本研究中, 与其他评估的因素相比, 品牌因素对满意度有较大的影响. 鉴于国内咖啡文化变得越来越高级, 大专院校的学生对这一趋势也很敏感, 所以学生有很多可选择的品牌. 在韩国最高级的咖啡店, 外墙是玻璃建造的并可以打开, 内部是充满异国情调的开放式厨房. 这些高级咖啡店作为标志的功能复合大专院校学生的品味. 韩国咖啡店已成为一个文化品牌. 从品牌因素来看, 为了让顾客觉得这些咖啡店是高级的, 高质量的设备和提供更好服务的措施应当建立起来. 韩国咖啡馆作为蓬勃发展的行业品牌竞争加剧的结果表明, 提供与竞争对手不同的额外服务是有必要的. 顾客可以免费使用扫描仪. 另一个可以用来提高品牌的战略是提供和经营为集体学习而准备的讨论会议室. 如果咖啡馆采取这些类型的策略, 学院/大学的学生将更有可能认为他们承担的费用是值得的, 随后, 他们将可能更满足这些咖啡馆的品牌, 并更愿意再次光顾. 性别和学习年数对总体满意度和再光顾的意愿有最消极的营销. 女学生比男学生更容易满足和再光顾. 三, 四年级的学生比一, 二年级的学生更容易满足和再光顾. 喝咖啡的学生, 单独在咖啡店看书, 用笔记本电脑是很容易被注意到的. 高年级学生为了有效地利用时间用于自我发展和寻找工作往往独自光顾咖啡店. 从积极的差距来看, 经济效率这一因素对总体满意度和愿意再光顾有最大的影响. 与咖啡价格一起, 学生实际满意度（差距）越高, 总体满意度和再光顾的意愿也越高. 有消极差距的经济效率队再光顾有消极营销的结果表明较小的消极差距可以让再光顾的意愿更高. 在持续恶化的市场环境中, 坐落在大专院校附近的咖啡店采取诸如积分或会员卡, 和信用卡 公司的战略联盟, 发展套餐菜单或季节菜单和免费咖啡服务这些战略来提高竞争力. 就消极差距而言产品功率也有消极的影响, 这表明较高的负差距会导致较低的再光顾的意愿. 因为还有更多的客户比前几十年, 在这十年里更喜欢咖啡, 新一代的客户, 即学院/大学的学生, 希望除了咖啡还有更重菜单项目. 因此, 咖啡店应当增加配菜项目, 如华夫饼, 糕, 蛋糕, 三明治和沙拉. 例如, 星巴克韩国正在努力加强卖草莓糕, 艾草香味, 南瓜产品, 并提供免费的咖啡或奶油. 总而言之, 咖啡馆应注重提高其经济效率, 品牌和产品功率, 以加强大专院校学生的满意度. 由于店铺毗邻学大专院校可享受地缘优势, 就经济效率, 品牌和产品功率而言提供不同的服务, 很可能会提高客户满意度和回访. 咖啡厅的品牌, 因此, 应不断创新和变化, 以满足顾客的愿望. 由于这项研究只是针对在首尔的大专院校的学生, 需要针对不同地区和年龄组的比较研究来概括本研究的结果和建议.

• Asia Marketing Journal
• /
• 제12권4호
• /
• pp.55-78
• /
• 2011

외식업계에서는 충성도제고를 위한 장기적 고객 관리 프로그램으로서 사용금액 대비 일정률의 포인트를 적립해주는 고객보상(로열티)프로그램을 시행해왔으며, 단기적인 매출 증대를 목적으로 신용카드사나 이동통신사와의 전략적 제휴를 통해 소비자에게 할인혜택을 제공하는 제휴할인카드를 경쟁적으로 도입하고 있다. 포인트 적립과 제휴카드할인 프로그램은 추구하는 목적은 서로 다르나 소비자에게는 동일한 구매시점에 둘 중에서 하나를 선택해야하는 경합적인 대안이 된다. 일반적으로 소비자는 손실에 대해 더 민감하게 반응하는 위험회피 성향을 보이며, 실용적 동기에 의한 취득 및 거래효용의 관점에서 할인이 강력한 구매 동기가 되므로, 분리된 이익으로서의 포인트 적립 보다 할인 혜택을 제공함으로써 손실의 감소로 인식되는 제휴카드할인이 더 선호될 것으로 예상할 수 있다. 기업의 입장에서도 제휴기업간의 비용분담을 통해 보다 적은 비용으로 큰 소비자 할인혜택을 제공할 수 있다는 비용효율의 장점 및 경쟁 대응 필요성 때문에 제휴카드할인을 도입하게 된다. 그러나 할인판촉은 실제적인 비용이 투입되므로 매출의 증가를 통해 비용 보다 큰 수익이 보장될 때만 의미를 가지는 촉진 수단이다. 외식업의 경우 방문객수가 증가해야 매출의 증대를 이룰 수 있으며 운영효율이 향상된다. 테이블당 고객수 증가는 공간효율을 높여주어 이익개선에 기여가 크다. 따라서 제휴카드할인이 실제적인 기업성과향상을 가져오려면 할인이 객수의 증가 특히 테이블당 객수의 증가에 기여를 해야 한다. 제휴카드할인이 객수증가 및 이익률의 향상에 도움이 되는지의 여부를 알아보기 위하여 패밀리 레스토랑업체의 실제 매출 데이터를 사용하여 검증해 본 결과 포인트 적립제도는 객수 증가와 유의적 관계를 보이지 않은 반면 제휴할인은 객수 증가에 실제적인 영향이 있음이 밝혀졌으며, 할인율이 증가하면 테이블당 고객수도 증가하며 약 25%의 할인이 제공되면 추가로 한 명의 고객이 유인되는 효과가 있었다. 또한 수익성의 측면에서는 1인당 지불금액 즉 객단가는 할인율의 증가에 따라 하락하는 경향을 보였지만 객수의 증가로 인한 추가이익이 추가비용을 상쇄하고 있어서 제휴할인카드의 도입이 비용 대비 효과의 측면에서 적극적으로 고려할 수 있는 촉진 수단임이 입증되었다. 본 연구는 기업의 실측 데이터를 활용하고 있다는 점에서 소비자 태도나 의도의 변화를 기준으로 기업의 의사 결정 정보를 제공하고자한 기존연구보다 현실적인 접근을 하고 있다. 즉, 기업의 실제 데이터로 제휴카드할인 프로그램의 효과를 측정하였고, 포인트 적립 및 차감제도를 직접 비교함으로써 기업에게 향후 마케팅 전략 수립에 관한 현실적인 시사점을 제공하였다는 점에서 연구의 의의를 찾을 수 있을 것이다.

• 한국유통학회지:유통연구
• /
• 제15권3호
• /
• pp.71-110
• /
• 2010

본 연구에서는 항공권 예약 발권 웹사이트의 서비스 품질을 측정 뿐만 아니라 서비스 회복도 측정하고자 하였다. 또한 서비스 품질과 서비스 회복이 고객만족 및 충성의도에 미치는 영향관계를 실증하고자 하였다. 온라인 서비스 품질과 온라인 서비스 회복의 측정을 위해 Parasuraman, Zeithaml, & Malhotra(2005)가 개발한 E-S-QUAL과 E-RecS-QUAL을 사용했으며, 했다. E-S-QUAL은 온라인 서비스 품질을 측정하는 도구로써, 효율성, 시스템 이용가능성, 이행성, 프라이버시의 4개 차원 22개 항목으로 구성된다. E-RecS-QUAL은 온라인 서비스 회복을 측정하는 도구로써, 반응, 보상, 접촉의 3개 차원 11개 항목으로 구성된다. 실증분석을 위한 설문조사는 항공사나 여행사의 웹사이트를 통해 국내 외 항공권을 구입해 본 경험이 있는 소비자를 대상으로 실시하였는데, 총 400부가 회수되었고, 이 중 342부를 최종분석에 사용하였다. 실증분석을 위해 AMOS 7.0과 SPSS 15.0을 사용하였다. 먼저, SPSS 15.0을 사용하여, 요인점수를 이용한 회귀분석으로 가설검증을 한 결과, <가설 I-1, 2, 3, 4, II-1, 2, 3, III-1, IV-1>이 전부 채택되었다. 온라인 서비스 품질과 온라인 서비스 회복의 각 차원은 모두 전반적인 서비스 품질에 유의한 영향을 보였고, 전반적인 서비스 품질은 고객만족에 유의한 영향을 미쳤다. 마지막으로 고객만족 역시 충성의도에 유의한 영향을 미치는 것으로 확인되었다. 한편 AMOS 7.0을 사용하여 모형 분석을 하였는데, 모형의 적합도는 가설검증을 하기에 합당한 수치가 나왔다. 이를 토대로 가설검증을 한 결과, <가설 I-1, 3, II-1, 3, III-1, IV-1>은 채택되었고, <가설 I-2, 4, II-2>는 기각되었다. 이 결과는 Parasuraman et al.(2005)이 주장한 것처럼 E-S-QUAL을 나타내는 데는 요인점수를 이용한 회귀분석이 더 적합하다는 것을 보여주는 것이라고 판단된다. 이를 토대로 본 연구의 시사점을 정리하였다.

• Asia pacific journal of information systems
• /
• 제19권3호
• /
• pp.69-98
• /
• 2009

We investigated what factors motivate gamers to participate in a guild and why they continue to be engaged as members of the guild. We find that, based on the result of focus group interviews with MMORPG gamers, social support and self-esteem factors play important roles. Considering both prior research and the focus group interviews we have conducted, we define social support and character control as independent variables. Character identity, guild identity, and self-esteem are proposed as mediating variables while guild flow and game loyalty as dependent variables. Accordingly, we develop the research model and hypotheses, and verify them empirically. Based on our experiences of playing the WoW game, we proposed a research model and conducted focus-group interviews (FGIs). FGIs involve formulating a hypothesis and then collecting some relevant data. FGIs were conducted face-to-face with students of C University in Korea. We formulated structured interview schedules, and the questions were based on our research variables and personal experiences. The questions for the interviews encompassed the following areas: (a) the demographic characteristics of the focus group; (b) the number of years for which respondents had played online games; (c) the motive for starting a game; (d) the number of game-characters assumed by each gamer; (e) the type of game played; and (f) other issues such as the reasons for involvement in the play, the willingness to reuse the game in case new versions were released, etc. On average, it took two hours to interview each of three groups. A primary set of FGIs was conducted with three groups on the premise that there would be some differences caused by character race (Horde vs. Alliance) or by playable server (Normal vs. Combat). With respect to the manner of playing, we found that guild members shared information, felt a sense of belonging, and played computer games for quite a long time through the guild; however, they did not undergo these experiences when playing alone. Gamers who belonged to a specific guild helped other players without expecting compensation for that, freely shared information about the game, gave away items for free, and more generous with other members who made mistakes. The guild members were aware of the existence other members and experienced a sense of belonging through interactions with, and evaluations from, other players. It was clear that social support was shown within the guild and that it played an important role as a major research variable. Based on the results of the first FGIs, a second set of in-depth FGIs was carried out with a focus on the psychology of the individual within the guild and the social community of the guild. The second set of FGIs also focused on the guild's offline meetings. Gamers, over all, recognize the necessity of joining a community, not only off-line but also online world of the guild. They admit that the guild is important for them to easily and conveniently enjoy playing online computer games. The active behavior and positive attitudes of existing guild members can motivate new members of the guild to adapt themselves to the guild environment. They then adopt the same behaviors and attitudes of established guild members. In this manner, the new members of the guild strengthen the bonds with other gamers while feeling a sense of belonging, and developing social identity, thereby. It was discovered that the interaction among guild members and the social support encouraged new gamers to quickly develop a sense of social identity and increase their self-esteem. The guild seemed to play the role of socializing gamers. Sometimes, even in the real world, the guild members helped one another; therefore, the features of the guild also spilled over to the offline environment. We intend to use self-esteem, which was found through the second set of FGIs, as an important research variable. To collect data, an online survey was designed with a questionnaire to be completed by WoW gamers, who belong to a guild. The survey was registered on the best three domestic game-sites: 'WoW playforum,' 'WoW gamemeca,' and 'Wow invent.' The selected items to be measured in the questionnaire were decided based on prior research and data from FGIs. To verify the content of the questionnaire, we carried out a pilot test with the same participants to point out ambiguous questions as a way to ensure maximum accuracy of the survey result. A total of 244 responses were analyzed from the 250 completed questionnaires. The SEM analysis was used to test goodness-of-fit of the model. As a result, we found important results as follows: First, according to the statistics, social support had statistically significant impacts on character control, character identity, guild identity and self-esteem. Second, character control had significant effects on character identity, guild identity and self-esteem. Third, character identity shows its clear impact on self-esteem and game loyalty. Fourth, guild identity affected self-esteem, guild flow and game loyalty. Fifth, self-esteem had a positive influence on the guild flow. These days, the number of virtual community is rising along with its significance largely because of the nature of the online games. Accordingly, this study is designed to clarify the psychological relationship between gamers within the guild that has been generally established by gamers to play online games together. This study focuses on the relationships in which social support influences guild flow or game loyalty through character control, character identity, guild identity, and self-esteem, which are present within a guild in the MMORPG game environment. The study results are as follows. First, the effects of social support on character control, character identity, guild identity and self-esteem are proven to be statistically significant. It was found that character control improves character identity, guild identity and self-esteem. Among the seven variables, social support, which is derived from FGIs, plays an important role in this study. With the active support of other guild members, gamers can improve their ability to develop good characters and to control them. Second, character identity has a positive effect on self-esteem and game loyalty, while guild identity has a significant effect on self-esteem, guild flow and game loyalty. Self-esteem affects guild flow. It was found that the higher the character and guild identities become, the greater the self-esteem is established. Contrary to the findings of prior research, our study results indicate that the relationship between character identity and guild flow is not significant. Rather, it was found that character identity directly affects game players' loyalty. Even though the character identity had no direct effect on increasing guild flow, it has indirectly affected guild flow through self-esteem. The significant relationship between self-esteem and guild flow indicates that gamers achieve flow, i.e., a feeling of pleasure and excitement through social support. Several important implications of this study should be noted. First, both qualitative and quantitative methods were used to conduct this study. Through FGIs, it was observed that both social support and self-esteem are important variables. Second, because guilds had been rarely studied, this research is expected to play an important role in the online community. Third, according to the result, six hypotheses (H1, H5, H6, H7, H8, and H11) setup based on FGIs, were statistically significant; thus, we can suggest the corresponding relationships among the variables as a guideline for follow-up research. Our research is significant as it has following implications: first, the social support of the guild members is important when establishing character control, character identity, guildidentity and self-esteem. It is also a major variable that affects guild flow and game loyalty. Second, character control when improved by social support shows notable influence on the development of character identity, guild identity and self-esteem. Third, character identity and guild identity are major factors to help establish gamers' own self-esteem. Fourth, character identity affects guild flow through self-esteem and game loyalty. The gamers usually express themselves through characters; the higher character identity is, the more loyalty a gamer has. Fifth, guild identity, established within the guild, has clear effects on self-esteem, guild flow and game loyalty. Sixth, qualitative and quantitative methods are employed to conduct this study. Based on the results of focus group interviews and SEM analysis, we find that the social support by guild members and psychological factors are significant in strengthening the flow of guild and loyalty to the game. As such, game developers should provide some extra functions for guild community, through which gamers can play online games in collaboration with one another. Also, we suggest that positive self-esteem which is built up through social support can help gamers achieve higher level of flow and satisfaction, which will consequently contribute to minimizing the possibility for the players to develop negative attitude toward the guild they belong to.

• 마케팅과학연구
• /
• 제17권4호
• /
• pp.141-173
• /
• 2007

본 연구는 점포를 방문하는 동안 노출되는 매장의 물리적 환경 특성이 서비스 브랜드 개성과 재구매의도에 미치는 영향력을 규명하기 위해 시도되었다. 이를 위해 연구모형을 개발하여, 특정 서비스 브랜드의 이용객을 대상으로 설문조사를 실시하고 구조방정식을 이용하여 분석하였다. 연구 결과는 우선, 서비스의 물리적 환경은 주변요인, 디자인요인, 사회요인으로, 그리고 서비스브랜드 개성은 유능함, 성실함, 흥분됨, 세련됨, 강인함 차원으로 분류되었다. 둘째, 물리적 환경의 모든 차원들이 모든 서비스 브랜드 개성차원에 정(+)의 영향을 주었으며, 물리적 환경의 서비스 브랜드 개성에 대한 영향력은 각 차원별로 상이하였다. 셋째, 서비스 브랜드 개성은 모두 재구매의도에 정(+)의 영향을 주었으며, 특히 세련됨 차원에 미치는 영향이 가장 켰다. 넷째, 서비스의 물리적 환경은 재구매의도에 정(+)의 영향을 주었으며, 특히 물리적 환경 중 사회요인이 재구매의도에 가장 큰 영향을 주는 것으로 나타났다. 이와 같은 결과들은 물리적 환경 연출은 브랜드 개성 형성의 결정요인으로 서비스 브랜드 차별화의 핵심요인으로 작용하므로, 호의적인 브랜드 개성 창출을 위해서는 우선적으로 물리적 환경에 대한 효율적 관리 방안이 강구되어야 함을 보여준다.

• Clinical and Experimental Reproductive Medicine
• /
• 제2권2호
• /
• pp.27-36
• /
• 1975

The success of the family planning program in Korea is reflected in the decrease in the growth rate from 3.0% in 1962 to 2.0% in 1971, and in the decrease in the fertility rate from 43/1,000 in 1960 to 29/1,000 in 1970. However, it would be erroneous to attribute these reductions entirely to the family planning program. Other socio-economic factors, such as the increasing age at marriage and the increasing use of induced abortions, definitely had an impact on the lowered growth and fertility rate. Despite the relative success of the program to data in meeting its goals, there is no room for complacency. Meeting the goal of a further reduction in the population growth rate to 1.3% by 1981 is a much more difficult task than any one faced in the past. Not only must fertility be lowered further, but the size of the target population itself will expand tremendously in the late seventies; due to the post-war baby boom of the 1950's reaching reproductive ages. Furthermore, it is doubtful that the age at marriage will continue to rise as in the past or that the incidence of induced abortion will continue to increase. Consequently, future reductions in fertility will be more dependent on the performance of the national family planning program, with less assistance from these non-program factors. This paper will describe various approaches to help to the solution of these current problems. 1. PRACTICE RATE IN FAMILY PLANNING In 1973, the attitude (approval) and knowledge rates were quite high; 94% and 98% respectively. But a large gap exists between that and the actual practice rate, which is only 3695. Two factors must be considered in attempting to close the KAP-gap. The first is to change social norms, which still favor a larger family, increasing the practice rate cannot be done very quickly. The second point to consider is that the family planning program has not yet reached all the eligible women. A 1973 study determineded that a large portion, 3096 in fact, of all eligible women do not want more children, but are not practicing family planning. Thus, future efforts to help close the KAP-gap must focus attention and services on this important large group of potential acceptors. 2. CONTINUATION RATES Dissatisfaction with the loop and pill has resulted in high discontinuation rates. For example, a 1973 survey revealed that within the first six months initial loop acceptance. nearly 50% were dropouts, and that within the first four months of inital pill acceptance. nearly 50% were dropouts. These discontinuation rates have risen over the past few years. The high rate of discontinuance obviously decreases the contraceptive effectiveness. and has resulted in many unwanted births which is directly related to the increase of induced abortions. In the future, the family planning program must emphasize the improved quality of initial and follow-up services. rather than more quantity, in order to insure higher continuation rates and thus more effective contraceptive protection. 3. INDUCED ABORTION As noted earlier. the use of induced abortions has been increase yearly. For example, in 1960, the average number of abortions was 0.6 abortions per women in the 15-44 age range. By 1970. that had increased to 2 abortions per women. In 1966. 13% of all women between 15-44 had experienced at least one abortion. By 1971, that figure jumped to 28%. In 1973 alone, the total number of abortions was 400,000. Besides the ever incre.sing number of induced abortions, another change has that those who use abortions have shifted since 1965 to include- not. only the middle class, but also rural and low-income women. In the future. in response to the demand for abortion services among rural and low-income w~men, the government must provide and support abortion services for these women as a part of the national family planning program. 4. TARGET SYSTIi:M Since 1962, the nationwide target system has been used to set a target for each method, and the target number of acceptors is then apportioned out to various sub-areas according to the number of eligible couples in each area. Because these targets are set without consideration for demographic factors, particular tastes, prejudices, and previous patterns of acceptance in the area, a high discontinuation rate for all methods and a high wastage rate for the oral pill and condom results. In the future. to alleviate these problems of the methodbased target system. an alternative. such as the weighted-credit system, should be adopted on a nation wide basis. In this system. each contraceptive method is. assigned a specific number of points based upon the couple-years of protection (CYP) provided by the method. and no specific targets for each method are given. 5. INCREASE OF STERILIZA.TION TARGET Two special projects. the hospital-based family planning program and the armed forces program, has greatly contributed to the increasing acceptance in female and male sterilization respectively. From January-September 1974, 28,773 sterilizations were performed. During the same time in 1975, 46,894 were performed; a 63% increase. If this trend continues, by the end of 1975. approximately 70,000 sterilizations will have been performed. Sterilization is a much better method than both the loop and pill, in terms of more effective contraceptive protection and the almost zero dropout rate. In the future, the. family planning program should continue to stress the special programs which make more sterilizations possible. In particular, it should seek to add the laparoscope techniques to facilitate female sterilization acceptance rates. 6. INCREASE NUMBER OF PRIVATE ACCEPTORS Among the current family planning users, approximately 1/3 are in the private sector and thus do not- require government subsidy. The number of private acceptors increases with increasing urbanization and economic growth. To speed this process, the government initiated the special hospital based family planning program which is utilized mostly by the private sector. However, in the future, to further hasten the increase of private acceptors, the government should encourage doctors in private practice to provide family planning services, and provide the contraceptive supplies. This way, those do utilize the private medical system will also be able to receive family planning services and pay for it. Another means of increasing the number of private acceptors, IS to greatly expand the commercial outlets for pills and condoms beyond the existing service points of drugstores, hospitals, and health centers. 7. IE&C PROGRAM The current preferred family size is nearly twice as high as needed to achieve a stable poplation. Also, a strong boy preference hinders a small family size as nearly all couples fuel they must have at least one or more sons. The IE&C program must, in the future, strive to emphasize the values of the small family and equality of the sexes. A second problem for the IE&C program to work. with in the: future is the large group of people who approves family planning, want no more children, but do not practice. The IE&C program must work to motivate these people to accept family planning And finally, for those who already practice, an IE&C program in the future must stress continuation of use. The IE&C campaign, to insure highest effectiveness, should be based on a detailed factor analysis of contraceptive discontinuance. In conclusion, Korea faces a serious unfavorable sociodemographic situation- in the future unless the population growth rate can be curtailed. And in the future, the decrease in fertility will depend solely on the family planning program, as the effect of other socio-economic factors has already been maximumally felt. A second serious factor to consider is the increasing number of eligible women due to the 1950's baby boom. Thus, to meet these challenges, the program target must be increased and the program must improve the effectiveness of its current activities and develop new programs.