• 대한의용생체공학회:의공학회지
• /
• 제6권2호
• /
• pp.1-8
• /
• 1985

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70$\pm$1.32mmHg/min)compared to CF dialyzers(4.32$\pm$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500, 550, 570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500, 550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100, 300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3, 000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.SpO2 with Plethysmograph.

• 한국우주과학회:학술대회논문집(한국우주과학회보)
• /
• 한국우주과학회 1993년도 한국우주과학회보 제2권2호
• /
• pp.17-17
• /
• 1993

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70${\pm}$1.32mmHg/min)compared to CF dialyzers(4.32${\pm}$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500,550,570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500,550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100,300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3,000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.

• Journal of the Korean Wood Science and Technology
• /
• 제2권2호
• /
• pp.8-12
• /
• 1974

한국의 목재 인공 건조법을 개발하기 위하여 필자의 전직 대학인 전북대학교 전 김두헌 총장님, 동농대전 백남혁학장 및 동농대교수 제위의 각별한 협조를 얻어 1956년 고액을 지불하고 미국 More Dry Kiln Co.에서 최신의 목재 인공 건조 장치를 도입하여 전북 농대 임학과에 설치하게된 것이다. 그러나 이 건조 시설을 활용하는데는 많은 지장이 있었으므로 1959년 전기 More Dry Kiln의 온, 습도 조절장치만을 이용한 소형 Dry kiln을 제작하여 본 시험을 실시한 것이다. 공시수종은 소나무, 낙엽송, 은행나무, 전나무, 밤나무 및 감나무등이며, 공시목의 크기는 것이 60cm, 넓이 10cm 및 두께 15-35mm이다. 실험한 건조 조건은 건조 온도를 일정히 ($170^{\circ}F$)하고, 관계습도를 각종으로 변화할때 얻어지는 건조 속도를 측정하는 동시에 각 건조조건에 의하여 유발되는 건조결함을 조사하여 공시목의 초기 함수율과 건조 최경함수율 특히 shell의 함수율과의 비가 이들의 결함 형성 특히 표면경화(casehardening) 형성에 미치는 영향을 구명하였으며 또한 casehardening 계산식을 유도하였다. 1. 목재내부에 형성된 응력 즉 prong이 개주할 때의 응력은 prong이 서로 접합할 때의 응력을 100으로 하는 백분율에 의하여 다음식으로 표시할 수 있다. 단, 응력 측정에 사용한 prong은 그림 1과 같이 작성하여야 한다. $CH=\frac{(A-B') (4W+A) (4W-A)}{2A[(2W+(A-B')][2W-(A-B')]}{\times}100%$ 상식은 다음과 같은 간이식을 사용할 수 있다. $CH=\frac{A-B'}{A}{\times}200%$ 2. 일정 한 건조 조건하에 건조하여 항중에 달하고, 또한 normal casehardening을 형성하는 경우에 는, 그 sample board의 shell 의 함수율은 특히 얇은 sample board에 있어서 US Dep. Agr., Forest Products Laboratory에서 발표한 EMC 보다 낮다. 3. 본 실험에서 측정한 1시간당 목재 건조 표면적 $1cm^2$ 당 증발하는 증발량 즉 건조속도를 비교 검토한 결과 다음과 같은 순위로 되었으며, 비교 검토한 5수 종중 최대치를 유하는 은행나무 MC 20% 에 있어서 최저치를 표시한 밤나무의 3.8배가 된다. (표 1 참조) (1) 은행나무 (2) 감나무 (3) 소나무 (4) 낙엽송 (5) 밤나무 특히 함수율 26% 이하에 있어서 각 함수율에 대한 증발속도치는 다음과 같은 일차식으로 표시 할 수 있으며, 그 회귀계수 유의성 검정에 있어서의 T치는 다음과 같이 각각 고율의 유의성을 표시하였다. (표2 참조) 상기중 Y는 증발속도($g/cm^2hr$.), X는 함수율을 각각표시한다. 이들 회귀직선을 도시하면 그림 2와 같다. 4. 초기함수율과 건조 최종기에 있어서의 목재의 표층 함수율 즉 shell의 함수율과의 비(SR)가 casehar dening 형성에 미치는 영향은 다음과 같다. 어떤 SR 값에 관하여 그 SR 값 이하를 유하는 총개제수(N) 중 CH 제4급이 출현하는 수(D)의 확율 즉 N에 대한 D의 출현확율 P%는 표 3과 같다. (D의 출현확율 P%를 위험확율이라고 가칭한다.) 표 4에 있어서 종란의 1,2,3의 숫자는 각각 다음과 같은 사항을 표시한다. (1) CH 값 제 4급이 출현하지 아니 하는 안전한 최소 SF 값 (2) 위험을 30%를 허용하는 경우에 있어서의 SF 값의 한계 (3) CH 값 제 4급 이하가 발생하지 아니하는 위험율 100%의 값의 범위 상기한 실측 결과에 의하여 밤나무, 낙엽송등은 내부응력 형성이 용이한데 비하여 감나무, 소나무등은 내부응력 형성이 용이하지 아니하여, 특히 전나무, 은행나무등은 타수종과 동일한 건조조건에 있어서 reverse casehardening을 초래함에 비추워 타수종에 비하여 현저히 내부응력 특히 normal casehardening이 잘 형성되지 아니한다는 것을 알 수 있다. 5. casehardening을 제외한 각종의 drying defects는 long time loading에 있어서 그 내부응력이 ultimate stress를 초과할 때 나타나는 것인데 건조조건 온도 $170^{\circ}F$에 대하여 습도를 낮게하여도 그렇게 심하지 아니하나, 온도 $200^{\circ}CF$의 저습에 있어서 end coating을 하지 아니하는 경우에는 용이하게 발생한다. 특히 밤나무는 실험한 타수종에 비하여 casehardening 및 활열성 defects가 강한 것을 지적할 수 있다.

• 한국작물학회지
• /
• 제26권1호
• /
• pp.1-31
• /
• 1981

수도품종들의 저온에 대한 생리생태적 반응특성을 구명하여 내냉성 품종육성과 냉해를 경감 수 있는 재배법개선기술을 확립하고저 1975년부터 1980년에 걸처서, 유일형과 일본형 및 인도형 품종들을 공시하여 그들의 생육시기별 시비조건별 저온반응의 특성을 검토하기 위하여 저온처리를 작물시험장 인공기상실에서 그러고 저수온처리에 관한 시험을 작물시험장 춘천출장소 냉수시험지에서 수행한 바 그 결과를 요약하면 다음과 같다. 1. 15\circ_C 저온하에서 70% 이상의 실용적 발아율 얻을 수 있는 기간은 일본형품종들은 15\circ_C에서 10 일간, 통일형품종들은 15 일간이었다. 통일형품종들의 저온발아성 검정은 저온에서 장기간 실시하는 것 보다 16\circ_C에서 6일간 치상하는 것이 적당하였다. 2. 유묘의 저온저항성은 3.0～3.5 엽기묘가 가장 낮고 묘영이 진전됨에 따라 점차 높아켰으며 3엽기와 6엽기의 저온저항성간에 는 고도의 정상관을 보였다. 3. 주ㆍ야 15～10\circ_C온도에서는 일본형 및 통일형 품종 모두 42일 처리정도에서 식물체가 고사하고 20～15\circ_C에서는 일본형 품종은 분벽이 잘 이루어지나 통일형품종은 약관 억제되며 25～15\circ_C에서는 양품종군 모두 분벽이 촉진되었다. 그러나 초장신장 속도는 저온일 수록 저하되었다. 4. 이삭의 지경 및 영화분화는 출수전 30일부터 출수기까지 주ㆍ야 25～20\circ_C처리와 30～25\circ_C 처리시에는 모든 품종에서 잘 이루어졌으나 20～15\circ_C 처리구에서는 통일형품종은 지경 및 영화 분화수화수가 전자에 비하여 감소하였고 일본형품종은 큰 차이가 없었으나 이삭의 추출은 억제되었다. 5. 저기온에 의한 출종지연은 감수분열기에 저온처리한 것이 분얼최성기에 저온처리한 것 보다도 1～3일 이 지연되였으며 같은 시기에서는 저온처리 일수가 길수록 출수지연도가 컸다. 6. 벼 생육기간별로 17\circ_C냉수를 10일간 처리한 경우에 출수지연도는 분얼기 > 감수분열기 > 수잉기의 순이였고 품종별로는 수원26004 > 수원23005 > Lengkwang의 순이있다 냉수처리에 의한 출수지연도는 간장단축률 및 불임율과 유의한 정의 상관을 보였다. 7. 감수분열기의 저기온(15\circ_C)과 고기온(25\circ_C)처리는 고기온(25\circ_C)과 저기온(17\circ_C) 처리보다 간장단축율이 켰으며 이삭 추출도도 낮았고 장간종인 Lengkwang은 단간종인 수원26004에 비하여 저기온에서의 간장단축율이 낮은 경향이었다 이삭 추출도는 출수기에 저온처리를 하였을 때 가장 낮았으며 통일형품종은 일본형품종보다 이삭 추출도가 현저히 낮았고 저온에 의하여 간장단축도 심한 품종은 이삭 추출도도 매우 낮았으며 이들 간에는 고도의 유의한 정의 상관이 있었다. 8. 분벽기의 냉수처리는 수수를 증대시키고 감수분열기의 냉수처리는 수수를 감소시켰다. 생육시기별로 냉수처리시기가 빠를수록 간장단축율이 크고 이삭 추출도도 낮아졌다. 9. 감수분열기의 17\circ_C 저온처리에 의한 불임유발은 3일간 처리로서는 크게 나타나지 않으나 9 일간처리에서는 심하게 나타났으며 수원26004와 밀양4002가 저온처리에서 불임율이 가장 낮았다. 저온처리가 임실장해를 가장 크게 유발한 것은 출수전 15일부터 출수전 5일까지 사이의 처리였으며 일본형인 진흥은 통일형인 통일, 수원26004보다 임실장해가 현저히 적었다. 그러나 감수분열기의 저온처리에 의한 임실장해정도와 출수기의 저온처리에 의한 임실장해정도간에는 유의한 정의 상관을 보였으며 또한 저온에 의하여 이삭 추출도가 낮거나 간장단축율이 큰 품종은 임실율도 떨어지는 경향이었다. 10. 냉수처리에 의한 임실장해는 감수분열기처리(엽이간장-15～10cm)에서 가장 크고 품종별로는 수원26004, 조생통일 > 농백, Towada > 저온저항성이 강한 Lengkwang순이었다. 냉수처리시의 수심과 유수의 위치는 임실비율과 매우 밀접한 관계가 있으며 수심이 20～40cm로서 유수의 위치가 물속에 있면 수원26004는 불임율이 높았고 유수의 위치가 물위에 있었던 Lengkwang은 불임율이 낮았다. 11. 수전기에 3 일간 15\circ_C의 저온처리를 한 경우 등숙에 큰 영향이 없었으나 6 일간 처리한 경우에는 수원287호와 수원 26004만이 60% 이하의 임실율을 보였으며 9 일간 처리한 경우에는 모든 품종에서 임실율이 60^ 이하로 떨어겼다. 그러나 출수 10일 후부터 17\circ_C로 20일간 처리한 경우에는 등숙장해가 크지 않았다. 12. 질소, 인산, 가리, 칼슘, 마그네지움 및 아연등의 양분흡수는 19$^{\circ}C$ $\pm$ 5보다 $25^{\circ}C$ $\pm$ 5에서 흡수가 증대되었으나 망간은 반대로 평균 25\circ_C보다 19$^{\circ}C$에서 흡수가 더욱 많았다. 13. 냉수답에서 질소, 인산, 규산 및 퇴비시용은 분벽 및 수수를 증가시키고 임실율을 향상시키며 수량을 증대시켰다.

• 미술자료
• /
• 제96권
• /
• pp.123-154
• /
• 2019

국립중앙박물관 소장 <인왕선영도(仁旺先塋圖)>(덕수5520)는 그림과 발문(跋文) 열 폭으로 이루어진 병풍으로, 작가는 조중묵(趙重黙)(1820~1894 이후), 주문자는 박경빈(朴景彬)(생몰년 미상), 발문을 쓴 사람은 홍선주(洪善疇)(생몰년 미상), 제작연대는 1868년이다. 국립중앙박물관은 낱장으로 보관되어 온 <인왕선영도>를 병풍으로 복원하고 특별전 '우리 강산을 그리다: 화가의 시선, 조선시대 실경산수화'에서 최초로 공개하였다. <인왕선영도>에는 오늘날 서울특별시 서대문구 홍제동과 홍은동을 아우르는 인왕산 서쪽 실경이 묘사되어있고 원경에는 북한산 연봉이 그려져 있다. 화면 속에는 인왕산(仁旺山), 추모현(追慕峴), 홍재원(弘濟院), 삼각산(三角山), 대남문(大南門), 미륵당(彌勒堂)이라는 지명이 표기되어있다. 이 지역을 나타낸 조선후기 지도와 비교해보면 지형 표현과 지명 표기에 유사성이 있다. 조중묵은 넓은 공간을 포착하기 위해 지도의 지리정보를 숙지하였을 것으로 추정된다. 실경의 현장을 답사한 결과, 조중묵은 각각의 경물을 과장하거나 생략하였고 수평의 화면에 나열식으로 조합하였음을 알 수 있었다. 조중묵은 남종화풍 정형산수에 뛰어났던 화가로, <인왕선영도>의 세부 표현에서 사왕파(四王派) 화풍의 영향을 찾을 수 있다. 19세기 도화서 화원들이 화보를 활용하여 가옥을 그리거나 토파에 호초점을 찍고 당분법(撞粉法)으로 꽃을 나타내는 등 장식적인 화풍을 구사한 경향도 부분적으로 나타난다. <인왕선영도>에는 바위를 짙은 먹으로 쓸어내리듯 붓질한 기법, 산세의 괴량감, 가로로 붓을 대어 단순하게 그린 소나무 등 18세기 정선(鄭敾)(1676~1759)의 개성적 양식도 가미되어있다. 조중묵은 인왕산 실경산수로 유명한 정선의 양식과 권위를 차용한 것으로 추정된다. 그러나 <인왕선영도>는 유기적 공간감과 현장의 인상이 잘 드러나지 않으며, 연폭 화면이라는 매체도 조중묵의 개인 양식과 잘 어울리지 않는다. <인왕선영도>는 발문의 텍스트와 화면의 이미지가 잘 조응하는 작품이다. 발문의 내용을 여섯 단락으로 나누어 보면 ①무덤의 주인공과 이장 경위, ②무덤의 입지와 풍수, ③묘제(墓祭)와 신이(神異)한 응답, ④무덤 관리에 대한 마을 사람들의 협력, ⑤병풍 제작의 동기인 박경빈의 효성과 수묘(守墓), ⑥발문을 쓴 의의로 파악된다. 이 가운데 화면에서 시각적으로 구현하기 용이한 ②의 내용은 화면에 충실하게 재현되었다. <인왕선영도> 제작의 직접적 동기인 ⑤를 보면 주문자 박경빈이 "무덤이 마치 새롭게 단장한 것 같이 눈에 완연하다."라 하여 <인왕선영도>에 만족했음을 알 수 있다. 경물 하나하나를 설명하듯 나열한 구도는 회화미는 떨어지더라도 무덤의 풍수지리를 전달하는 데는 더 적합했을 것으로 추정된다. 현존하는 상당수의 산도(山圖)는 18세기 이후 제작된 목판본 선영도로서, 족보와 문집에 수록된 경우가 많다. 16~17세기의 기록에서는 족자 선영도를 첨배(瞻拜)의 대상으로 삼은 사례를 찾을 수 있다. 선영도 첨배는 현실적으로 수묘(守墓)가 곤란할 때 이를 대신할 수 있는 의례로 인정되었다. 한효원(韓效元)(1468~1534), 조실구(曺實久)(1591~1658) 등이 선영도를 제작한 후 당대의 명사에게 서문을 요청하고 효심을 과시한 사례는 <인왕선영도>의 선구가 된 것으로 추정된다. <석정처사유거도(石亭處士幽居圖)>(개인 소장), <화개현구장도(花開縣舊莊圖)>(국립중앙박물관) 등은 선영도는 아니지만 계회도 형식의 족자이고 풍수를 도해했다는 점에서 17세기 선영도의 모습을 유추할 수 있는 자료가 된다. <인왕선영도>는 첨배라는 측면에서 초상화와도 의미가 비슷했다. 발문의 "부친의 기침소리를 직접 접하는 듯하고, 그 태도와 몸가짐을 눈으로 보는 듯하다."는 표현과 부친의 초상에 조석 문안을 올린 서효숙 고사에서 그 단초를 찾을 수 있다. 박경빈이 일반적인 선영도 형식이었던 족자나 목판화 대신 연폭 병풍의 실경산수화를 주문한 의도는 분명히 알기 어렵다. 19세기에는 민간에서도 사례(四禮) 의식에 다수의 병풍을 배설(排設)하였는데, 의례의 성격에 따라 그림의 주제를 반드시 구분하여 사용한 것은 아니었다. <인왕선영도> 또한 여러 의례에 두루 배설하거나 장식 병풍으로도 사용하기 위해서 선영 그림이라는 주제를 실경산수화 이미지 아래에 가렸을 가능성이 있다. 특히 <인왕선영도>의 핵심 소재인 무덤 봉분이 모호하게 처리된 것은 사산금표(四山禁標)의 금제 위반을 숨기기 위함일 가능성이 있다. <인왕선영도>에 묘사된 인왕산 서쪽 산기슭은 분묘 조성 금지구역이었다. 1832년에 금표 내에 몰래 쓴 묘를 적발하여 즉시 파내고 관련자를 엄히 처벌한 사례로 볼 때, 19세기 중엽까지도 사산금표 내의 분묘 금제는 효력을 발휘하고 있었던 것으로 추정된다. <인왕선영도>의 발문에는 장지를 얻기 위해 쏟은 정성이 상세하게 쓰여 있다. 장지조성에 마을사람들의 협조와 묵인이 필요했던 것은 금표 구역 내에 묘지를 조성하는 것이 부담스러운 일이었기 때문으로 볼 수 있다. <인왕선영도>와 비교 가능한 동시대 연폭 병풍의 실경산수화로 이한철(李漢喆)(1808~1880)이 그린 <석파정도(石坡亭圖)>(미국 로스앤젤레스카운티미술관)를 들 수 있다. <석파정도> 제작시기를 전후한 1861년에 이한철과 조중묵은 철종어진도사에 함께 참여하였으므로 조중묵이 이한철의 <석파정도> 제작 과정을 보았을 가능성은 상당히 높다. 조중묵이 몇 년 후 <인왕선영도>를 주문받았을 때 <석파정도>의 인상적인 연폭 실경산수를 본 경험이 반영되었을 가능성이 있다. 두 작품의 화풍 차이는 주문자의 취향과 제작 목적의 차이에서 비롯된 것으로 추정된다. <인왕선영도>는 실경산수화와 선영도의 중층적인 구조를 가지고 있어서 관람자의 지식수준과 주문자와의 친분, 관람에 들이는 시간에 따라 천차만별의 의미로 수용되었을 것이다. <인왕선영도>의 발문에는 무덤 주인의 이름과 자호, 본관이 일체 작성되지 않은 채 '박공(朴公)'이라고만 표기되어 있다. 주문자인 박경빈의 인적 사항도 파악할 수 없었으나 다만 관직에 나아가지 못한 가계를 미루어 볼 때 재력이 있음에도 지배계층으로 올라설 수 없는 신분적 한계를 지니고 있었음은 짐작할 수 있다. 발문을 쓴 홍선주 또한 사대부로 보기 어려우며, 『승정원일기』 기록에 나타나는 경아전 서리일 가능성이 있다. 박경빈은 상류 계층에 진입하고 싶은 욕망으로 보수적인 가치인 효(孝)를 강조하여 부친의 무덤을 명당으로 이전하고 <인왕선영도>를 제작하였을 것으로 추정된다. 그러나 <인왕선영도>는 금제위반 적발에 대한 우려, 병풍의 다목적성 등의 이유로 본래의 제작의도를 뚜렷하게 드러내지 못하고 모순적인 이미지가 되었다. 병풍이 제작된 지 47년 만에 각 폭이 분리된 채 미술상을 통해 이왕가미술관 소장품이 된 상황을 보더라도, 박경빈이 <인왕선영도>에서 꿈꾸었던 명당 발복과 가문의 신분상승은 이루어지지 못했던 것으로 생각된다.