• 비파괴검사학회지
• /
• 제21권6호
• /
• pp.634-641
• /
• 2001

형상기억복합재료는 복합재료내에 압축잔류응력을 발생시킴으로써 재료의 인장강도를 증가시키는데 사용되어 지고 있다. 본 연구에서는 형상기억복합재료를 제조하기 위하여 TiNi 강화재와 A16061 기지재를 사용하였으며 핫프레스 방법에 의해 TiNi/A16061 형상기억복합재료를 제조하였다. 그러나 핫 프레스 방법에 의해 제조된 형상기억복합재료는 하중을 받을 시 강화재와 기지재 사이에 계면손상현상이 발생하였으며 이를 위하여 내간압연을 실시하였다. 냉간압연을 받은 시험편은 냉간압연을 받지 않은 시험편에 비하여 인장강도가 현저히 증가하였다. 또한 본 연구에서는 고온에서 형상기억복합재료의 미시적 손상을 평가하기 위하여 음향방출기법을 이용하였다.

• 대한기계학회논문집A
• /
• 제33권2호
• /
• pp.99-107
• /
• 2009

This study produced a design curve and fatigue limit for a variation in volume ratio and reduction ratio of TiNi/Al composites. In many cases, stress-life curve does not indicate fatigue limit, so it was presented by probabilistic-stress-life curve. Goodman diagram was used to analyze the fatigue strength of materials with a finite life determined by repeated load and the fatigue strength of endurance limit with an infinite life. The fatigue experiment was conducted using the scenk-type plane bending specimen in same shape. The result of the fatigue test, which had been conducted under consistent stress amplitude, was examined. (i) The optimal condition for TiNi/Al in accordance with hot pressing (ii) Impacts of fatigue limit caused by a variation in reduction ratio and volume ratio of TiNi/Al composites (iii) Probability distribution for fatigue limit of TiNi/Al2024 and TiNi/Al6061.

• 한국재료학회지
• /
• 제7권11호
• /
• pp.951-956
• /
• 1997

Vacuum Hot Pressing을 이용하여 제조한 TiNi형상기억섬유 강화 6061 AI기지 복합재료를 제조하고 미세조직 및 기계적 특성 등을 연구하였다. 제조된 복합재의 항복응력은 예비변형량, 섬유체적율 및 열처리에 따라 증가하였다. 복합재의 지적특성은 예비변형이 가하여진 후 재가열되었을 때 기지 내 TiNi 섬유의 형상기억효과에 의한 압축잔류응력 발생에 기인된다. 미세조직 관찰 섬유와 기지 사이에는 AI$_{3}$Ti및 AI$_{3}$Ni의 금속간화합물층이 관찰되었다. 또한 시험온도 증가와 더불어 TiNi섬유강화된 복합재의 유동강도는 높은 값을 나타내었다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.687-691
• /
• 2001

Al alloy matrix composite with TiNi shape memory fiber as reinforcement has been fabricated by hot pressing to investigate mechanical properties. The stress-strain behavior of the composites was evaluated at temperatures between 363K and room temperature as a function of pre-strain by using experimental and finite element analysis, and both cases showed that the tensile stress at 363K was higher than that of the room temperature. Especially, the tensile stress of this composite increases with increasing the amount of pre-strain, and it also depends on the volume fraction of fiber and heat treatment. The smartness of the composite is given due to the shape memory effect of the TiNi fiber which generates compressive residual stress in the matrix material when heated after being pre-strained.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 추계학술대회 논문집
• /
• pp.243-244
• /
• 2006

• 한국자동차공학회논문집
• /
• 제6권6호
• /
• pp.53-62
• /
• 1998

A simple analytical and finite element(FE) models are used to study the tensile properties of Al matrix composite with continuous TiNi fibers. The effects of residual stresses caused by the shape momory effects have been compared for various mechanical behaviors as a function of fiber volume fraction and degree of pre-strain and fiber configurations. It is found that both the back stress in the Al matrix induced by stiffness of TiNi fibers and the compressive stress in the matrix are caused of the strengthening mechanisms. Both theoretical and analytical results show quite good agreement and are closed to the experimental data except in high volume content.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.692-696
• /
• 2001

Thermo-mechanical behavior and mechanical properties of intelligent polymer matrix composite with SMA fiber are experimentally studied. It is found that increments of compressive thermal strain is observed as the pre-strain and TiNi volume fraction increase. The smartness of the SMA is given due to the shape memory effect of the TiNi fiber which generates compressive residual stress in the matrix material when heated after being prestrained. In the paper, alloy is based on the general purpose commercial code ANSYS. And for the purpose of easy and fast user's analysis, it is developed the Graphical User Interface by using Tcl/Tk language.

• 한국재료학회지
• /
• 제9권4호
• /
• pp.419-427
• /
• 1999

TiNi shape memory alloy was shape memory heat-treated and investigated its mechanical properties with the variation of prestrain. Also 6061 Al matrix composites with TiNi shape memory alloy fiber as reinforcement have been fabricated by Permanent Mold Casting to investigate the microstructures and interface properties. Yield stress of TiNi wire was the most high in the case of before heat-treatment and then decreased as increasing heat-treatment time. In each heat-treatment condition, the yield stress of TiNi wire was not changed with increasing the amount of prestrain. The interface bonding of TiNi/6061Al composite was fine. There was a 2$\mu\textrm{m}$ thickness of diffusion reaction layer at the interface. We could find out that this diffusion reaction layer was made by the mutual diffusion. The diffusion rate from Al base to TiNi wire was faster than that of reverse diffusion and the amount of the diffusion was also a little more than that of reverse.

• 대한기계학회논문집A
• /
• 제28권8호
• /
• pp.1099-1108
• /
• 2004

In this paper, a study on the development of expert system for Al matrix composite with shape memory alloy fiber is performed to evaluate termomechanical behavior and mechanical properties. Expert system is very useful computer-based analysis system designed to make analysis technique and knowledge conveniently available to a lot of fabricable condition. In the developed system, it is possible to predict termomechanical behavior and mechanical properties for other composite with shape memory alloy fiber. The smartness of the shape memory alloy is given due to the shape memory effect of the TiNi fiber which generates compressive residual stress in the matrix material when heated after being prestrained. For finite element analysis, an analytical model is assumed two dimensional axisymmetric model compared of one fiber and the matrix. To evaluate the strength of composite using FEM, the concept of smart composite was simulated on computer Thus, in this paper, the FEA was carried out at two critical temperature conditions; room temperature and high temperature(363k). The finite element analysis result was compared with the test result for the analysis validity.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.465-469
• /
• 1997

In this paper, shape memory compsites are made by powder metallurgy. And then, an self-strengthening effect of the composites by shape memory effect above inverse transformation temperature A/sab f/ of TiNi alloy discussed. Moreover, TiNiCo/Al composite is made by using TiNiCo alloy as fiber. And it is discused aboutaffection of Co in the shape memory composite. The results of the intelligent properties of TiNi/Ai-radical shape memory composite, using SMA, by powder metallurgy are the tensile strength of TiNiCo wire is much higher than that of TiNi wire. and the strength of TiNiCo/Al composite is generally higher than that TiNi/Al composite.