• Journal of the Korean institute of surface engineering
• /
• v.31 no.6
• /
• pp.317-324
• /
• 1998

TiN and TiCN films were deposited on the high speed steel by Cathode Arc Ion Plating(CAIP) Process to investigate the tool life extension effect. The experiment variables were bias voltage and deposit time for the TiN coating and reactive gas flow rate ($CH_4:N_2$) under fixing deposit pressure, are current, bias voltage for the TiCN coating respectively. The micro structure and mechanical properties were investigated and compared for among the coating conditions using various methods and machining practice.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.11
• /
• pp.32-37
• /
• 1996

Using the are ion plating(AIP) process, TiN coating was deposited onto high speed steel substrates. The effects of coating thickness, titanisum interlayer and shield on wear resisting capability of the coated tools were investigated. In order to promote good adhesion between the substrate and the TiN coating a thin Ti interlayer was deposited. A shield was set up also between Ti target and high speed steel substrates to prevent molten droplets from reaching the substrate. Three series of varying thickness of TiN coated layer were prepared with or without the Ti interlayer, and with or without the shield. The tools with the Ti layer and the shield showed longer tool lifes than those of other series of tools and the commercially available TiN coated HSS tools, by up to 70%.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.21 no.5
• /
• pp.848-854
• /
• 2012

SCM420 steel cutting gear to improve the durability is quenched. When quenching, increases surface hardness, a change of the physical properties and machinability or fall. This study, using a solid carbide hobs skiving hobbing gear cutting finishing. And cutting tool solid carbide TiAlN coating hove when TiAlN coating on the surface of multi-con polishing hob conducted aero lap nano polishing for each cutting. Experimental results conducted aero lap nano coating on the surface polishing tool machinability was excellent. And aero lap nano polishing tool results were reduced 2.5 times the tool wear compared to TiAlN coated tools. Excellent results were 1.42 times longer tool life.

• Journal of the Korean institute of surface engineering
• /
• v.31 no.6
• /
• pp.400-406
• /
• 1998

Tool life characteristics were investigated for the TiN coated (PVD) tungsten carbide cutting tools to improve the tool life Experimental variables for Tin coating were coating time and cathode bias voltage and cuting variables were cutting speed and feel rate. As a experiment result, TiN coated tool was extended about from 2.14 to 2.7 times than that of not coated tungsten carbide tools. Also, coating thinkness is much affected to tool life.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.1
• /
• pp.47-52
• /
• 2005

In this paper, the effect of TiN-coating on product quality such as dimensional accuracy and surface roughness is experimentally investigated. A punch of SKD11 material in cold forging an automotive bearing shaft and its related process found in a cold forging company are selected as the test example. The effect of TiN-coating is revealed in a quantitative manner. It is to be noted that TiN-coating is effective in controlling the dimensional accuracy and surface roughness as well as in increasing tool lift.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2003.10a
• /
• pp.89-94
• /
• 2003

Hard coatings are known to improve the performance of cutting tools in aggressive machining applications, such as high speed machining. New superhard Ti-Al-Si-W films, characterized by a nanocomposite nano-sized (Ti,Al,Si)N crystallites embedded in amorphous $Si_3 N_4$ matrix, could be successfully synthesized on WC-Co substrates by a hybrid coating system of arc ion plating(AIP) and sputtering method. The hardness of Ti-Al-Si-N film increased with incorporation of Si, and had the maximum value ~50 GPa at the Si content of 9 at.%, respectively. And the X-ray diffraction patterns of Ti-Al-Si-N films with various Si content is investigated. In this study, Ti-Al-Si-N coatings were applied to end-mill tools made of WC-Co material by a hybrid coating system. Cutting tests fir the high-hardened material (STD11,$H_R$)C62 and their performances in high speed cutting conditions were studied. Also, the tool wear and tool lift of Ti-Al-Si-N with various si(6, 9, 19) contents were measured.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.3
• /
• pp.705-712
• /
• 1995

The wear characteristics and wear mechanisms in TiN coating deposited on high speed steel and alloy tool steel by ion plating were investigated. Pin on V-block wear tester was used for a wear test method. The specimen was composed of three kinds of high speed steel and alloy tool steel which had different hardness by changing the heat treating condition. Three kinds of coating thickness were also applied to each specimen. Microscopic observation of worn surfaces was made by SEM. The scratch test of coating surface by the ion plating showed that critical load to break the coating interface was greater than 50N. The critical load increased with both substrate hardness and coating thickness. The wear resistance of TiN coated high speed steel became 10 times greater than that of non-coated ones. SEM observation showed that leading edge of contact was compressive and trailing edge was under maximum tensile stress and then surface cracking broke out perpendicular to sliding direction.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.18 no.7
• /
• pp.42-47
• /
• 2019

In this research, we try to study the change of squareness in the cutting process while changing cutting conditions such as feed rate and spindle rotational speed with chromium molybdenum steel (SCM415) material and TiCN, TiAlN coated end mill tool. The TiCN coating tool had the best straightness at 4,000 rpm at a feed rate of 200 mm/min. The TiAlN coating tool was best measured at 3,000 rpm at a feed rate of 200 mm/min. TiAlN coated tools had excellent dimensional tolerance when comparing the coating tool specifics.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.14 no.2
• /
• pp.1-7
• /
• 2005

In order to determine the wear Properties of PECVD ceramic coatings, wear process was evaluated using the coated pin of Falex Tribosystem. Coating materials deposited wear the TiC, TiN and Ti(CN). An experimental process was established to determine the tribological characteristics of friction and wear behavior under the variation of applied load, temperature and sliding distance by the Falex test machine. The experimental results indicate that TiN coating compared with TiC coating on e materials have e excellent friction and wear characteristics. However TiC coating compared i친 TiN coatings have a low friction coefficient with steel and good thermal stability, and Ti(CN) has the excellent anti-wear properly as well as the superiority of extreme pressure property. Compound coating compared wi simple coatings show improved tribological characteristics.

• Journal of the Korean institute of surface engineering
• /
• v.33 no.4
• /
• pp.222-228
• /
• 2000

The life time of cutting tool was studied in the relation with the properties of TiN coating tools. The purpose of this study is to compare the cutting conditions of the TiN coated tools with those of the non-coated tools and to find out the optimal cutting condition of the TiN coated tool. The coated tools were prepared by the sputtering process at $4$\times$10^{-3}$Torr. When the cutting speed is increased 22.2% from 90m/min, the limited life of coating bite was decreased by 60.61%, but non-coating bite was decreased by 64.05%. In the tool lifetime equation of the coated tools "a"(exponent of feed rate) was not much changed in comparison with that of the non-coated tools but "n" (exponent of tool′s life) was increased by 9.3% and "b" (exponent of cutting depth) was increased by 2.4%. It was thought to be that TiN coated tools was used for higher cutting speed than non-coated tools to improve the lifetime of the coated tools.