• Tribology and Lubricants
• /
• 제23권4호
• /
• pp.170-174
• /
• 2007

Wear and scuffing tests were conducted using friction and wear measurement of piston rings and cylinder blocks in low friction diesel engine. The frictional forces, wear amounts and cycles to scuffing in boundary lubricated sliding condition were measured using the reciprocating wear tester. The cylinder blocks were used as reciprocating specimens, and the piston rings with several coatings were used as fixed pin. Several coatings were used such as DLC, TiN, Cr-ceramic and TiAlN in order to improve the tribological characteristics. From the tests wear volume of piston ring surfaces applied various coatings were compared. During the tests coefficients of friction were monitored. Test results showed that DLC coatings showed good tribological properties. TiN and Cr-ceramic coated rings showed good wear resistance properties but produced high friction.

• 대한기계학회논문집A
• /
• 제30권10호
• /
• pp.1179-1186
• /
• 2006

This paper was designed to assess the adhesive properties of hard coatings on non-nitrided and nitrided various tool steels. Estimations of adhesion were done to scratch test which is mainly used in hard coating. The critical load$(L_c)$ between coating and substrate is defined through analysis of frictional load vs. normal load curve, signals of acoustic emission and optical observations. Coatings employed in this study are TiN, CrN and TiAlN, tools as substrates are STD11, STD61 and SKH51. It was classified to substrates with/without intermediate nitrided layer and hard coatings on substrate were deposited by arc PVD. Results showed that harder substrates and coatings give higher values of critical loads.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 추계학술대회 논문집
• /
• pp.186-189
• /
• 2005

This paper was designed to assess the adhesive properties of hard coatings on non-nitrided and nitrided various tool steels. Estimations of adhesion were done to scratch test which is mainly used in hard coating. The critical load(Lc) between coating and substrate is defined through analysis of frictional load vs. normal load curve, signals of acoustic emission and optical observations. Coatings employed in this study are TiN, CrN and TiAlN, tools as substrates are STD11, STD61 and SKH51. It was classified to substrates with/without nitrided layer and hard coatings on substrate were deposited by arc PVD. Results showed that harder substrates and coatings give higher values of critical loads.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2006년도 춘계학술발표회 초록집
• /
• pp.153-153
• /
• 2006

• 한국결정성장학회지
• /
• 제22권4호
• /
• pp.183-189
• /
• 2012

고온 열수송용 재료로 이용되는 Hastelloy X의 표면처리에 따른 고온물성 개선에 대한 연구를 수행하였다. Hastelloy X 기판 상에 각각 PVD법인 Arc discharge 및 Sputtering을 이용하여 TiAlN 및 $Al_2O_3$ 박막을 표면 코팅(overlay coating) 하였고, 분위기 분말을 이용하여 Al을 금속표면을 통해 확산시키는 방법인 Pack cementation법을 이용한 Al 확산코팅(diffusion coating: aluminiding)법을 이용한 표면처리를 수행하였다. 이들 표면처리가 Ni-Cr계 합금의 고온열처리에서 생성되는 두꺼운 불균질 산화물($Cr_2O_3$)형성 억제에 미치는 효과와 조성 및 표면미세구조가 물성에 미치는 영향에 대해 알아보기 위해, 표면처리 된 Hastelloy X 샘플들을 공기 및 헬륨가스 분위기에서 $1000^{\circ}C$로 열처리 하였으며, 열처리된 전후 시편들에 대해 상형성, 미세구조 및 고온 물성 변화를 측정하였다. 이러한 실험결과를 통하여 표면코팅법에 의한 TiAlN 및 $Al_2O_3$ 박막에 비해 Al 확산코팅한 경우 두꺼운 불균질 산화물($Cr_2O_3$)형성이 억제되어 보다 균질한 미세구조와 높은 내마모성 등 높은 고온 안정성을 보여주는 것을 확인할 수 있었다.

• 대한금속재료학회지
• /
• 제47권2호
• /
• pp.129-137
• /
• 2009

Corrosion behaviors of TiN coated dental casting alloys have been researched by using various electrochemical methods. Three casting alloys (Alloy 1: 63Co-27Cr-5.5Mo, Alloy 2: 63Ni-16Cr-5Mo, Alloy 3: 63Co-30Cr-5Mo) were prepared for fabricating partial denture frameworks with various casting methods; centrifugal casting(CF), high frequency induction casting(HFI) and vacuum pressure casting(VP). The specimens were coated with TiN film by RF-magnetron sputtering method. The corrosion behaviors were investigated using potentiostat (EG&G Co, 263A. USA) in 0.9% NaCl solution at $36.5{\pm}1^{\circ}C$. The corrosion morphologies were analyzed using FE-SEM and EDX. Alloy 1 and Alloy 2 showed the ${\alpha}-Co$ and ${\varepsilon}-Co$ phase on the matrix, and it was disappeared in case of TiN coated Alloy 1 and 2. In the Alloy 3, $Ni_2Cr$ second phases were appeared at matrix. Corrosion potentials of TiN coated alloy were higher than that of non-coated alloy, but current density at passive region of TiN coated alloy was lower than that of non-coated alloy. Pitting corrosion resistances were increased in the order of centrifugal casting, high frequency induction casting and vacuum pressure casting method from cyclic potentiodynamic polarization test.

• 한국표면공학회지
• /
• 제54권3호
• /
• pp.133-138
• /
• 2021

Ternary Ti-X-N coatings, where X = Al, Si, Cr, O, etc., have been widely used for machining tools and cutting tools such as inserts, end-mills, and etc. Ti-Al-N-O coatings were deposited onto silicon wafer and WC-Co substrates by a cathodic arc evaporation (CAE) technique at various negative substrate bias voltages. In this study, the influence of substrate bias voltages during deposition on the microstructure and mechanical properties of Ti-Al-N-O coatings were systematically investigated to optimize the CAE deposition condition. Based on results from various analyses, the Ti-Al-N-O coatings prepared at substrate bias voltage of -80 V in the process exhibited excellent mechanical properties with a higher compressive residual stress. The Ti-Al-N-O (-80 V) coating exhibited the highest hardness around 30 GPa and elastic modulus around 303 GPa. The improvement of mechanical properties with optimized bias voltage of -80 V can be explained with the diminution of macroparticles, film densification and residual stress induced by ion bombardment effect. However, the increasing bias voltage above -80 V caused reduction in film deposition rate in the Ti-Al-N-O coatings due to re-sputtering and ion bombardment phenomenon.

• 한국정밀공학회지
• /
• 제31권6호
• /
• pp.513-519
• /
• 2014

For depth machining in die and mold, Electrical Discharge Machining (EDM) is used generally. To make deep hole and deep shape efficiently, cemented carbide endmill for depth machining is necessary. For this purpose, cemented carbide endmill was designed using design of experiment (DOE). To improve cutting performance, endmill was coated with multilayer surface treatment, TiAlCrSiN and TiAlCrN, for higher wear resistance. In order to evaluate the endmill, Transverse Rupture Strength (TRS) test was tried for investigating the relationship between surface treatment and strength in endmill body. Scratch test was also used for measuring adhesion force of each surface treatment. To evaluate hardness of surface treatment, Atomic Force Microscope (AFM) analysis was carried out. Wear test was executed for characteristics of each surface treatment in high temperature. Consequently, TiAlCrSiN was superior to the TiAlCrN coating in case of high temperature environment such as cutting.

• 한국진공학회지
• /
• 제15권1호
• /
• pp.110-116
• /
• 2006

본 연구에서는 나노 두께를 갖는 두 층을 반복적으로 증착하여 나노 다층 구조를 갖는 질화 물이 코팅된 절삭공구의 기계적 성능과 절삭성능의 향상에 대해 고찰하였다. 이러한 질화물계 나노 다층막에 대한 재료는 격자상수와 결정구조에 따라 $Ti_{0.54}Al_{0.46}N-CrN$계와 $Ti_{0.84}Al_{0.16}N-NlN$계를 선택하여, UBM sputtering 증착법을 이용하여 초경(WC-Co) 인서트(insert)위에 증착하였다. 공정 변수들인 증착온도, 압력. 기판 바이어스 전압, 기판회전 속도 등을 조절하여 다른 주기 값을 갖는 일정한 두께의 다층막들을 증착 시켰고, 주기에 따른 초격자 형성, 경도 값과 절삭성능을 관찰하였다. 증착된 다층막들은 그 주기 값에 따라 경도 값이 다르게 나타났으며. 경도 값이 상대적으로 높았던 특정 주기의 다층막이 코팅된 절삭 공구의 경우, 기존의 상용화된 제품에 비해 frank wear로 비교한 절삭 성능이 $20\%$이상 향상됨을 관찰하였다

• 소성∙가공
• /
• 제30권1호
• /
• pp.43-48
• /
• 2021

The success of warm forming of Mg alloy sheet is greatly influenced by friction at elevated temperature, depending on the surface treatment of the tool. The tool coating affected the frictional characteristics of AZ31B Mg alloy sheet at elevated and room temperatures. The frictional behavior of the Mg alloy sheet at room temperature was not significantly affected by surface treatment conditions of the tool, but was significantly affected at elevated temperature. When the contact pressure is high, a few surface-treated tools exhibit a higher coefficient of friction than those without surface treatment. It is important to select the surface treatment conditions of the tool in order to ensure appropriate friction during warm forming of Mg alloy sheet.