• 열처리공학회지
• /
• 제8권2호
• /
• pp.120-126
• /
• 1995

The effects of heating rate on the combustion temperature, the ignition temperature, the microstrurcture and the shape memory ability of products formed by combustion were investigated. The ignition temperature decreased with increasing heating rate. Combustion temperature and ${\Delta}T$(difference temperature between the ignition temperature and the combustion temperature) increased with increasing heating rate. The grain size of the product increased with increasing heating rate. Combustion synthesis did not completely occur below the heating rate of $10^{\circ}C/min$. NiTi intermetallic compound was completely formed at the heating rate of $600^{\circ}C/min$ and the product by combustion method had a good shape memory effect.

• 한국재료학회지
• /
• 제6권12호
• /
• pp.1199-1212
• /
• 1996

본 연구는 주조성, 내압성, 내열성 등이 우수하여 군용 및 민수용 기계소재로 이용되고 있는 AI-Si-Mg계 AC4C 합금에 세라믹(AI2O3, AI2O3-TiC)을 강화시키는 복합재료제조에 관한 기초연구의 일환으로 수행하였다. 연구내용은 세라믹 강화재의 젖음성을 높이기 위하여 수소환원법에 의한 AI2O3입자의 Ni 피복과 기존의 프리폰 제조방법보다 간단하고 경제적인 자전연소합성법에 의해 AI2O3-TiC 다공성 pellet을 제조하여, 이들 강화재와 AC4C 기지금속을 이용하여 고대-compocasting 및 squeeze casting법으로 복합재료를 제조하고 미세조직, 계면생성물, 기계적 성질, 내마멸성 등의 특성을 조사하였다. 고대-compocasting법에 의해 제조된 AI2O3Ni 입자 강화 복합재료에서 강화재들은 응집체로 존재하지 않고 비교적 균일하게 분산되었고 AI2O3-TiC 강화재를 이용하여 squeeze casting으로 가압주조 하므로써 기지금속과 강화재의 젖음성이 향상되었다.

• Journal of Industrial and Engineering Chemistry
• /
• 제68권
• /
• pp.124-128
• /
• 2018

Titanium doping is employed to enhance the structural strength of a high-Ni layered cathode material in lithium ion batteries during high temperature cycling. After Ti-doping, the external morphology remains similar, but the lattice parameters of the layered structure are slightly shifted toward larger values. With application of the prepared materials as cathodes in lithium-ion batteries, the initial capacities are similar but the cycling performance at $25^{\circ}C$ is enhanced by Ti-doping. During high temperature cycling at $60^{\circ}C$, furthermore, highly improved capacity retention is achieved with the Ti-doped material (95% of initial capacity at 50th cycles), while cycle fading is accelerated with the bare electrode. This enhancement is attributed to better retention of the compressive strength of the particles and retarded crack formation within the particles. In addition, impedance increase is reduced in the Ti-doped electrode, which is attributed to an improvement in the structural strength of the high-Ni cathode material with Ti-doping.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2003년도 춘계학술발표대회 개요집
• /
• pp.204-206
• /
• 2003

Ti/Steel 클래드 판재를 제조하기 위하여 티타늄과 강판을 직접 접합하는 경우 접합 계면에 취성이 강한 금속간화합물 및 TiC 탄화물이 발생하여 계면접합강도를 저하시키는 단점이 있다. 이러한 단점을 보완하기 위하여 본 연구에서는 티타늄과 강판 사이에 니켈 박판을 삽입한 후 1223-1323K 온도구간에서 접합 실험하였다. 특히, 온도의 변화에 따라 티타늄과 강판의 계면에 발생되는 금속간화합물의 종류 및 반응층의 크기 변화에 따른 기계적 특성을 조사하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 추계학술대회 논문집 Vol.18
• /
• pp.169-170
• /
• 2005

본 연구에서는 초음파 센서에 응용 가능한 $0.4Pb(Ni_{1/3}Nb_{2/3})O_3-0.6Pb(Zr_xTi_{1-x})O_3+0.5Wt%$ $MnO_2$ 세라믹스에 Zr/(Ti+Zr)비를 0.37에서 0.41로 변화시킨 조성을 1175 $\sim$ 1200$^{\circ}C$ 온도에서 소결하여 이의 결정구조 및 미세조직을 분석하였고, 압전, 유전 특성을 고찰하였다. 본조성에서 x=0.385 조성에서 최대 유전상수 값 3490 이 나타났으며, 그 이상의 첨가에서는 감소하였다. 상경계 영역인 x=0.385 조성에서 $\varepsilon$r, $K_p$, $d_{33}$ 값이 최대값을 나타내었다. $0.4Pb(Ni_{1/3}Nb_{2/3})O_3-0.6Pb(Zr_xTi_{1-x})O_3+0.5Wt%$ $MnO_2$, 세라믹스에서는 kp 와 $d_{33}$ 는 Zr/(Ti+Zr)비 0.385조성까지 증가하였다가 그 이상 조성에서 감소하였다. $1175^{\circ}C$에서 2시간 소결한 x=0.385조성에서 $\varepsilon$r=3490, kp=0.71, Qm=476의 우수한 압전 특성을 나타내었다.

• E2M - 전기 전자와 첨단 소재
• /
• 제10권2호
• /
• pp.134-140
• /
• 1997

PbTiO$_{3}$-PbZrO$_{3}$-Pb(Ni$_{1}$3/Nb $_{2}$3/O$_{3}$)(PZT-PNN) thin films were prepared from corresponding metal organics partially stabilized with diethanolamine by the sol-gel spin coating method. Each mol rates of PT:PZ:PNN solutions were #1(50:40:10), #2(50:30:20), #3(45:35:20) and #4(40:40:20), respectively. The spin-coated PZT-PNN films were sintered at the temperature from 500.deg. C to 600.deg. C for crystallization. The P-E hysteresis curve was drawn by Sawyer-Tower circuit with PZT-PNN film. The coercive field and the remanent polarization of #4(40:40:20 mol%) PZT-PNN film were 28.8 kV/cm and 18.3 .mu.C/cm$^{2}$, respectively. Their dielectric constants were shown between 128 and 1120, and became maximum value in MPB(40:40:20 mol%). The leakage currents of PZT-PNN films were about 9.4x 10$^{-8}$ A/cm$^{2}$, and the breakdown voltages were about 0.14 and 1.1 MV/cm. The Curie point of #3(45:35:20 mol%, sintered at 600.deg. C) film was 330.deg. C.

• 열처리공학회지
• /
• 제27권1호
• /
• pp.1-9
• /
• 2014

For connector material applications, the influence alloying elements of Mn, Cr, Fe, and Ti and cold rolling reduction on the mechanical property, electrical conductivity and bendiability of Cu-Ni-Si-P alloy was investigated. The hot rolled plates were solution treated at $980^{\circ}C$ for 1.5 h, quenched into water, cold rolled by 10% and 30% reduction in thickness, and then aged at $440{\sim}500^{\circ}C$ for 3, 4, 5 times. respectively. Cu-Ni-Si-P-x alloys cold rolled by 10 reduction before heat treatment have a good bendability compare to cold rolled by 30 reduction. Cu-3.4Ni-0.8Si-0.03P-0.1Ti shows the peak strength value of 759 MPa, an electrical conductivity of 39%IACS, an elongation of 10% and a hardness of 256 Hv aged at $440^{\circ}C$ for 6 hrs. Thus it is suitable for lead frame and connector.

• 공업화학
• /
• 제3권1호
• /
• pp.88-99
• /
• 1992

광 전기분해시 양극으로 사용되는 산화티타늄 반도체 전극의 안정성을 증대시키고 효율향상을 위해서 순수한 티타늄 전극을 양극 산화법, 전기로 산화법, 불꽃 산화법으로 산화 피막을 제조하였으며 In을 Ti와 $TiO_2$소지에 전기도금을 한 후 전기로 산화법으로 혼합 산화물을 제조하였다. 또한 $Al_2O_3$ 와 NiO는 진공증착 방법을 이용하여 Ti 소지위에 증착시킨 후 전기로 산화법을 이용하여 혼합 산화물을 제조하였다. 에너지변환 효율(${\eta}$)은 인가전위에 따라서 다른 값을 갖는데 0.6V로 계산하여 보면 $1200^{\circ}C$의 불꽃으로 2분간 산화시킨 전극이 0.98%로 가장 큰 값을 가졌으며 양극 산화법으로 제조한 전극의 ${\eta}$는 0.14%로 작은 값을 보여 주었다. 한편 $800^{\circ}C$ 전기로에서 10분간 산화시킨 전극의 ${\eta}$는 0.57%로 띠간 에너지는 2.9eV로 나타났다. 한편 In을 Ti 및 $TiO_2$ 소지위에 전기도금시킨 전극의 ${\eta}$는 0.8%였으며 인가전위가 증가함에 따라서 ${\eta}$는 증가하였다. 그러나 $Al_2O_3$와 NiO를 Ti소지위에 진공증착시킨 전극의 ${\eta}$는 다른 전극들에 비해서 가장 낮은 값을 나타내었다.

• 한국전기전자재료학회논문지
• /
• 제22권10호
• /
• pp.890-896
• /
• 2009

Li(Ni, Co, Mn)$O_2$ has been known as one of the most promising cathode materials for lithium secondary batteries. However, it has some problems to overcome for commercialization such as inferior rate capability and unstable thermal stability. In order to address these problems, surface modification of cathode materials by coating has been investigated. In the coating techniques, selection of coating material is a key factor of obtaining enhanced properties of cathode materials. In this work, we introduced solid electrolyte (Li-La-Ti-O) as a coating material on the surface of $Li[Ni_{0.3}Co_{0.4}Mn_{0.3}]O_2$ cathode. Specially, we focused on a rate performance of Li-La-Ti-O coated $Li[Ni_{0.3}Co_{0.4}Mn_{0.3}]O_2$ cathode. Both bare and Li-La-Ti-O 2 wt.% coated sample showed similar discharge capacity at 0.5C rate. However, as the increase of charge-discharge rate to 3C, the coated samples displayed better discharge capacity and cyclic performance than those of bare sample.

• 한국분말재료학회지
• /
• 제20권6호
• /
• pp.405-410
• /
• 2013

During sintering of Ni-electrode multi-layer ceramic capacitors (MLCCs), the Ni electrode often becomes discontinuous because of its lower sintering temperature relative to that of $BaTiO_3$. In an attempt to retard the sintering of Ni, we introduced passivation of the Ni powder. To find the optimal passivation conditions, a thermogravimetric analysis (TGA) was conducted in air. After passivation at $250^{\circ}C$ for 11 h in air, a nickel oxide shell with a thickness of 4-5 nm was formed on nickel nanoparticles of 180 nm size. As anticipated, densification of the compacts of the passivated Ni/NiO core-shell powder was retarded: the starting temperature of densification increased from ${\sim}400^{\circ}C$ to ${\sim}600^{\circ}C$ in a $97N_2-3H_2$ (vol %) atmosphere. Grain growth was also retarded during sintering at temperatures of 750 and $1000^{\circ}C$. When the sintering atmosphere was changed from wet $99.93N_2-0.07H_2$ to wet $99.98N_2-0.02H_2$, the average grain size decreased at the same sintering temperature. The conductivity of the passivated powder sample sintered at $1150^{\circ}C$ for 8 h in wet $99.93N_2-0.07H_2$ was measured to be $3.9{\times}10^4S/cm$, which is comparable with that, $4.6{\times}10^4S/cm$, of the Ni powder compact without passivation. These results demonstrate that passivation of Ni is a viable means of retarding sintering of a Ni electrode and hence improving its continuity in the fabrication of $BaTiO_3$-based multi-layer ceramic capacitors.