• Journal of the Korean Ceramic Society
• /
• v.30 no.7
• /
• pp.578-588
• /
• 1993

Highly c-axis oriented ferroelectric PbTiO3 thin films were deposited on MgO single crystal substrates by RF magnetron sputtering. We have studied the effects of substrate temperature, RF input power, gas comosition, gas pressure and deposition rate on the chemical and structural characteristics of PbTiO3 thin films. The epitaxy relationship of c-axis oriented films was found to be PbTiO3{100}//MgO(100) and their microstructures were highly mosaic. It was found that the most important parameter to achieve epitaxial PbTiO3 films was the substrate temperature. The activation energy for the epitaxy formation was about 0.92eV. Lower gas pressure and RF input power were favorable for the formation of epitaxial c-axis orientation. It was also found that the optimum oxygen content in Ar gas was 10% to obtain the stoichiometric PbTiO3 composition.

• The Korean Journal of Ceramics
• /
• v.4 no.3
• /
• pp.199-203
• /
• 1998

$Pb(Zr, Ti)O_3$ (Pb:Zr:Ti=1:0.52:0.48) thin films were prepared on single crystal MgO(100) substrates by dipping-pyrolysis process using a solution of constituent metal naphthenates as starting materials. The solution was spin-coated onto substrate and the precursor films were pyrolyzed at $200^{\circ}C$ in air or at $200^{\circ}C$ in argon for 1, 2, 5 and 24h, followed by final heat treatment at $750^{\circ}C$. For all the films, highly (h00)/(00l)-oriented Pb$Pb(Zr, Ti)O_3$ thin films with smooth surfaces and crack-free were obtained, whereas thin film pyrolyzed in air for 24 h exhibited polycrystalline character. According to the pole-figure analysis, epitaxy of the product films was found to depend on pyrolysis atmosphere.

• Journal of the Korean institute of surface engineering
• /
• v.39 no.2
• /
• pp.70-75
• /
• 2006

As technology advances, there is a demand for development of hard, solid lubricant coating. (Ti,Cr)N-$MoS_2$, films were deposited on SKD 11 tool steel substrate by co-deposition of $MoS_2$, with (Ti,Cr)N using a D.C. magnetron sputtering process. The influence of the $N_2/Ar$ gas ratio, the deposition temperature, the amount of $MoS_2$ in the films, and the bias voltage on the mechanical and the structural properties of the films were investigated. Wear tests were performed on the films deposited in various conditions.

• Journal of the Korean institute of surface engineering
• /
• v.30 no.1
• /
• pp.33-43
• /
• 1997

The effects of process parameters substrate such as substrate current and substrate temperature on the corrosion resistance of ion plated TiN film were investigated. TiN fims were deposited on speed steel on which Ti or Ni hed been previously evaporated. Dense TiN films could be obtained under higher substrate current(1A) and substrate temperature($500^{\circ}C$), whereas TiN films deposited with lower substances current(0.5A) and substrate temperature($300^{\circ}C$) showed porous structure. The corrosion resistances of high speed steel was considerably increased when dense TiN films had been formed on it. The effect of Ti and Ni interlayer on the increase of the corrosion resistance was also significant with dense TiN films, while there was little effect of interlayer on the corrosion resistance when TiN films were porous. the effect of interlayer on the corrosion resistance was more outstanding with Ti then with Ni, because Ti reacts more easily with oxygen to form an oxide layer, and it also shows higher resistance against chlorine containing corrosion media.

• Journal of the Korean Society for Heat Treatment
• /
• v.28 no.3
• /
• pp.134-138
• /
• 2015

Ag intermediated $TiO_2$ films were deposited by RF and DC magnetron sputtering and then vacuum annealed at 100, 200 and $300^{\circ}C$ for 30 minutes to investigate the effect of annealing temperature on the structural and optical properties of the films. For all depositions, the thickness of the $TiO_2$ and Ag films were kept constant at 24 and 15 nm by controlling the deposition time. As-deposited $TiO_2/Ag/TiO_2$ trilayer films have a weak crystalline and an optical reflectance in a near infrared wavelength region of 77.8%, while the films annealed at $300^{\circ}C$ show the polycrystalline structure and an increased mean optical reflectance of 80.4%. From the experimental results, it can be concluded that increasing the annealing temperature enhanced the structural and optical properties of the $TiO_2/Ag/TiO_2$ films.

• Journal of the Korean Ceramic Society
• /
• v.30 no.6
• /
• pp.441-448
• /
• 1993

The Ba1-xSrxTiO3 thin films deposited on ITO-coated glass substrate at 55$0^{\circ}C$ by rf magnetron sputtering method have individual preferential orientations as a function of composition (X=0, 0.25, 0.5, 0.75, 1) due to the stress relief interactions among the intrinsic compressive stress, thermal tensile stress adn extrinsic compressive stress (compressive stress in case of BaTiO3(Tc=12$0^{\circ}C$) and Ba0.75Sr0.25TiO3(Tc=57$^{\circ}C$)). This behavior also appears on the (BaSr)TiO3 thin films (X=0.5) deposited on ITO-coated glass substrate at deposition temperature between 35$0^{\circ}C$ and 55$0^{\circ}C$. The composition of Ba1-xSrxTiO3 thin films deposited on ITO-coated glass substrate at 55$0^{\circ}C$ is close to stoichiometry (1.009~1.089 in A/B ratio), but the compositional deviation from a stoichiometry is larger as SrTiO3 is added. The morphology of Ba1-xSrxTiO3 thin films is very similar for over all substrate temperatures, and the roughness due to the differences of cluster size is the smallest at X=0.25.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.8
• /
• pp.706-710
• /
• 2007

Ti-containing amorphous carbon (a-C:Ti) films shows attractive mechanical properties such as low friction coefficient, good adhesion to various substrate and high wear resistance. The incorporation of titanium in a-C films is able to improve the electrical conductivity, friction coefficient and adhesion to various substrates. In this study, a-C:Ti films were depositied on Si wafer by closed-field unbalanced magnetron (CFUBM) sputtering system composed two targets of carbon and titanium. The tribological properties of a-C:Ti films were investigated with the increase of DC bias voltage from 0 V to - 200 V. The hardness and elastic modulus of films increase with the increase of DC bias voltage and the maximum hardness shows 21 GPa. Also, the coefficient of friction exhibites as low as 0.07 in the ambient. In the result, the a-C:Ti film obtained by CFUBM sputtering method improved the tribological properties with the increase of DC bias volatage.

• Proceedings of the KIEE Conference
• /
• 2005.11a
• /
• pp.189-190
• /
• 2005

Ploycrystalline $Pb(Zr_{0.5},Ti_{0.5))O_3$ and $BaTiO_3$ powder were prepared by sol-gel process. The alumina substrate were sintered at $1400^{\circ}C$ with bottom electrode of Pt for 2 hours. The Pb(Zr0.5,Ti0.5)O3 / BaTiO3 multilayered thick films with laminating times were fabricated on alumina substrate by screening printing method. The obtained thick films were sintered at $800^{\circ}C$ with upper electrode of Ag paste for 1 hour. Structural properties of Pb(Zr0.5,Ti0.5)O3 / BaTiO3 multilayered thick films were investigated. As a result of the Differential Thermal Analysis(DTA) of Pb(Zr0.5,Ti0.5)O3, exothermic peak was observed at around 650 $^{\circ}C$. The X-ray diffraction (XRD) patterns indicated that BaTiO3 and Pb(Zr0.5,Ti0.5)O3 phases and porosities were formed in the interface of Pb(Zr0.5,Ti0.5)O3 / BaTiO3multilayered thick films.

• Proceedings of the KIEE Conference
• /
• 2005.07c
• /
• pp.1960-1961
• /
• 2005

Ploycrystalline $Pb(Zr_{0.5},Ti_{0.5})O_3$ and $BaTiO_3$ powder were prepared by sol-gel process. The alumina substrate were sintered at $1400^{\circ}C$ with bottom electrode of Pt for 2 hours. The Pb(Zr0.5, Ti0.5)O3/BaTiO3 multilayered thick films with laminating times were fabricated on alumina substrate by screening printing method. The obtained thick films were sintered at $800^{\circ}C$ with upper electrode of Ag paste for 1 hour, Structural properties of Pb(Zr0.5,Ti0.5)O3/BaTiO3 multilayered thick films were investigated. As a result of the Differential Thermal Analysis(DTA) of Pb(Zr0.5,Ti0.5)O3, exothermic peak was observed at around $650^{\circ}C$. The X-ray diffraction (XRD) patterns indicated that BaTiO3 and Pb(Zr0.5,Ti0.5)O3 phases and porosities were formed in the interface of Pb(Zr0.5,Ti0.5)O3 / EaTiO3 multilayered thick films.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.05b
• /
• pp.135-139
• /
• 2005

Thin films of $BaTiO_3$ system were prepared by radio frequency(rf)/dc magnetron sputtering method. We have investigated crystal structure, surface morphology and PTCR(positive-temperature coefficient of resistance) characteristics of the specimen depending on second heat-treatment temperatures. Second heat treatments of the specimen were performed in the temperature range of 400 to $1350^{\circ}C$. X-ray diffraction patterns of $BaTiO_3$ thin films show that the specimen heat treated below $600^{\circ}C$ is an amorphous phase and the one heat treated above $1100^{\circ}C$ forms a poly-crystallization. In the specimen heat-treated at $1300^{\circ}C$, a lattice constant ratio (c/a) was 1.188. Scanning electron microscope(SEM) image of $BaTiO_3$ thin films of the specimen heat treated in between 900 and $1100^{\circ}C}$ shows a grain growth. At $1100^{\circ}C$, the specimen stops grain-growing and becomes a poly-crystallization.