• 한국자기학회지
• /
• 제15권6호
• /
• pp.311-314
• /
• 2005

본 연구에서는 Al-Oxide(AIOx) 에 Ti를 첨가하여. Ti 함량에 따라 자기터널접합의 자기터널링 현상 변화 및 TiA l합금박막의 미세구조, 표면거칠기 변화를 관찰하였다. Ti를 첨가한 TiAlOx 절연층을 사용하여 기존 AlOx를 사용한 경우 보다 높은 터널링 자기저항(Tunneling Magnetoresistance, TMR) 비를 가지는 자기터널접합을 제작하였다. TMR 비의 증가 요인은 Ti를 첨가함에 따라, TiAl 합금박막의 입계가 작아지고, 치밀한 구조를 가져, 우수한 계면평활도를 가지는 균일한 TiAlOx 절연층이 형성되어, 소자의 구조적 안정성이 향상되었기 때문으로 분석하였다. 또한 향상된 구조적 안정성으로 인해 소자의 열적, 전기적 안정성도 크게 증가하였다.

• 한국자기공명학회논문지
• /
• 제4권1호
• /
• pp.1-11
• /
• 2000

Supported vanadium oxides are being used extensively as catalysts for a variety of reactions, including partial oxidations and ammoxidations. A series of vanadium oxide supported on TiO2-ZrO2 was obtained by impregnating ammonium metavanadate slowly into a mixed precipitateof Ti(OH)4-Zr(OH)4, followed by calcining in air at high temperatures. The prepared catalysts were characterized by 51V solid-state NMR. In the calcined catalysts 51V NMR studies indicated the peaks corresponding to distorted tetrahedral vanadia species at low V2O5 contents and octahedral vanadia species at high vanadia loadings. These results illustrate the suitability of 51V NMR as a unique quantitative spectroscopic tool in the structural analysis of vanadium(V) oxide catalytic materials.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 하계학술대회 논문집 Vol.8
• /
• pp.372-372
• /
• 2007

Titanium oxide nanotube arrays were fabricated by the anodization of pure titanium thin film deposited at $500^{\circ}C$ on silicon substrates. The titania nanotubes were grown by anodization in nonaqueous-base electrolytes at different potentials between 5 V and 30 V. $TiO_2$ nanotube array with a small pore diameter of 40 nm and long titanium oxide layer of $4\;{\mu}m$ was obtained. The $TiO_2$ nanotube array was used as a porous electrode for quartz crystal microbalance (QCM). Nanoporous morphology of electrode will increase the sensitivity of microbalance.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 하계학술대회 논문집 Vol.6
• /
• pp.409-411
• /
• 2005

A series of inorganic-organic hybrid membranes were prepared with a systematic variation of titanium dioxidenanoparticles content. Their water uptake, methanol permeability and proton conductivity as a function of inorganic oxide content were investigated. The results obtained show that the inorganic oxide network decreases the proton conductivity and water swelling. It is also found that increase in inorganic oxide content leads to decrease of methanol permeability. In terms of the morphology, membranes are homogeneous and exhibit a good adhesion between inorganic domains and the polymer matrix. The properties of the composite membranes are compared with the standard nation membrane.

• 한국전기전자재료학회논문지
• /
• 제14권1호
• /
• pp.1-5
• /
• 2001

STI(shallow trench isolation)-CMP(chemical mechanical polishing) process have been substituted for LOCOS(local oxidation of silicon) process to obtain global planarization in the below sub-0.5㎛ technology. However TI-CMP process, especially TI-CMP with RIE(reactive ion etching) etch back process, has some kinds of defect like nitride residue, torn oxide defect, etc. In this paper, we studied how to reduced torn oxide defects after STI-CMP with RIE etch back processed. Although torn oxide defects which can occur on trench area is not deep and not severe, torn oxide defects on moat area is not deep and not severe, torn oxide defects on moat area is sometimes very deep and makes the yield loss. Thus, we did test on pattern wafers which go through trench process, APECVD process, and RIE etch back process by using an IPEC 472 polisher, IC1000/SUVA4 PAD and KOH base slurry to reduce the number of torn defects and to study what is the origin of torn oxide defects.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.126-126
• /
• 2016

Understanding adsorption behavior organic molecules at oxide surfaces is very important for the application of organic-inorganic hybrid materials. Recently, monoethanolamine (MEA) adsorbed on $TiO_2$ surface has received great interests because it can lower the work function of $TiO_2$ in photo-electronic devices such as OLED and solar cells. In this study, we investigated the role of surface defects in adsorption behaviors of MEA at the rutile $TiO_2$ (110) surface by combined study of scanning tunneling microscopy and density functional theory calculations. Our results revealed that oxygen vacancy is the most stable adsorption site for MEA on $TiO_2$ (110) surface at low coverage. As coverage increases, the oxygen vacancies are occupied with the molecules and MEA molecules start to adsorb at Ti rows at higher coverages. Our results show that the defects at oxide surfaces and the intermolecular interactions are important factors for determining stable adsorption structure of MEA at $TiO_2$ (110) surfaces.

• 한국세라믹학회지
• /
• 제47권6호
• /
• pp.633-637
• /
• 2010

In this study, lithium manganese oxide spinel ($LiMn_{1.9}Fe_{0.1}Nb_{0.0005}O_4$) as a cathode material of lithium ion secondary batteries is synthesized with spray drying, and in order to increase its crystallinity and electrochemical properties, the granulated $LiMn_{1.9}Fe_{0.1}Nb_{0.0005}O_4$ particle surface is coated with lithium titanium oxide spinel ($Li_4Ti_5O_{12}$) through a sol-gel method. The granulated particles present a higher tap density and lower specific surface area. The crystallinity and discharge capacity of the $Li_4Ti_5O_{12}$ coated material is relatively higher than uncoated material. With the coating layer, the discharge capacity and cycling stability are increased and the capacity fading is suppressed successfully.

• 한국진공학회지
• /
• 제4권S2호
• /
• pp.156-162
• /
• 1995

For a stimulating neural electrode, the charge density should be as large as possible to provide adequate stimulation of the nervous system while allowing for miniaturization of the electrode. Since iridium oxide is able to produce high charge densities while preventing undesirable reactions due to charge storage, it has become a promising material for neural prostheses. Successful production of stable Ir and Ir oxide films on various substrates now limits the use of this material. Ir was deposited on two differently prepared surface of (mirror finish, passivation) surgical Ti-6AI-4V with several methods. Ion beam mixing of sputter deposited Ir films on passivated Ti-6AI-4V produced stable and good adherent Ir films. It was found that the increase in charge density of pure Ir on continuous cyclingis due to the accumulation of the oxide phase ( associated with a large surface area) in which the valence state of iridium changes and the double-layer capacitance increases. This study also showed that the double layer capacitance is equally or even more responsible for the high charge density of anodically formed Ir oxide.

• 대한금속재료학회지
• /
• 제47권9호
• /
• pp.573-579
• /
• 2009

Titanium/aluminum/stainless steel(Ti/Al/STS) clad materials have received much attention due to their high specific strength and corrosion-resisting properties. However, it is difficult to fabricate these materials, because titanium oxide is easily formed on the titanium surface during heat treatment. The aim of the present study is to derive optimized cladding conditions and thereupon obtain the stable quality of Ti/Al/STS clad materials. Ti sheets were prepared with and without pre-heat treatment and Ti/Al/STS clad materials were then fabricated by cold rolling and a post-heat treatment process. Microstructure of the Ti/Al and STS/Al interfaces was observed using a Scanning Electron Microscope(SEM) and an Energy Dispersed X-ray Analyser(EDX) in order to investigate the effects of Ti pre-heat treatment on the bond properties of Ti/Al/STS clad materials. Diffusion bonding was observed at both the Ti/Al and STS/Al interfaces. The bonding force of the clad material with non-heat treated Ti was higher than that with pre-heat treated Ti before the cladding process. The bonding force decreased rapidly beyond $400^{\circ}C$, because the formed Ti oxide inhibited the joining process between Ti and Al. Bonding forces of STS/Al were lower than those of Ti/Al, because brittle $Fe_3Al$, $Al_3Fe$ intermetallic compounds were formed at the interface of STS/Al during the cladding process. In addition, delamination of the clad material with pre-heat treated Ti was observed at the Ti/Al interface after a cupping test.

• 한국세라믹학회지
• /
• 제40권9호
• /
• pp.902-908
• /
• 2003

Au/TiO$_2$ core-shell 구조 나노 미립자가 졸-겔법에 의해서 제조되었고, TiO$_2$ shell의 형상과 결정성이 TEM과 UV-Vis. absorption spectrometer에 의해서 조사되었다. Au/TiO$_2$ core-shell 나노 미립자는 Au 콜로이드 에탄올 수용액 중에서 TOAA(Titanium Oxide Acethylacetonate)의 가수분해에 의해 합성될 수 있었다. Au 나노 미립자의 표면에 형성된 TiO$_2$ shell의 두께는 약 1 nm이었다. TiO$_2$ shell의 결정성을 조사하기 위하여. TiO$_2$가 피복된 Au 콜로이드 에탄올 용액에 254 nm의 자외선과 $^{60}$Co의 방사선을 조사하였다. Au 나노 미립자의 surface plasmon 현상은 방사선이 조사되었을 때만 나타났고, 이 결과로부터 TiO$_2$ shell은 비정질 상태임을 알 수 있었으며, Au의 분산성 향상을 위해 표면에 처리된 MUA(Mercaptoundecanoic Acid)층은 전자의 이동을 방해하는 장애물로 작용하지 않음을 확인할 수 있었다.