• Journal of the Korean Chemical Society
• /
• v.32 no.6
• /
• pp.543-548
• /
• 1988

The metal-support interaction was studied in 1∼5wt% copper supported on $\gamma-alumina$ and titania systems by temperature programmed reduction (TPR) and EPR. When the samples were treated with oxygen at $500^{\circ}C$, the relative area of H2-TPR peak at higher temperature increased with copper content for titania system whereas that of lower temperature increased for ${\gamma}$-alumina system. After oxygen treatment at $500^{\circ}C,\;{\gamma}$-alumina system showed a TPR peak at $300^{\circ}C$ while two peaks at 120 and $180^{\circ}C$ were found in titania system. A typical $Cu^{2+}$ EPR signal was observed on ${\gamma}$-alumina but very broad and small one on titania. From the results, it was suggested that the metal-support interaction increases in the order of silica < titania < ${\gamma}$-alumina and copper oxide has different loading characteristics depending on the supports.

• Clean Technology
• /
• v.17 no.3
• /
• pp.225-230
• /
• 2011

Characteristics of hydrocarbon selective catalytic reduction of NOx using various noble metal catalysts were investigated. The best active metal is Pt, supports are $CeO_2$ and $TiO_2$ by strong interactions between active metals, and 55% of conversion rate of NOx is shown. Pd, Rh and Ag catalysts presented a conversion of less than 20% as active metals, and supports also showed the poor activity compared to $SiO_2$ and $ZrO_2$. Experiments were performed with different types of reducing agents, amount, concentration of oxygen and space velocity in order to investigate the performance of catalysts according to operating conditions. The results confirm that the methane is better than propane as a reducing agent, and as the ratio of methane/nitrogen oxide increases, the catalytic activity increased, as the concentration of oxygen increases and space velocity decreases, the performance of catalysts increased.

• Korean Journal of Materials Research
• /
• v.11 no.9
• /
• pp.769-775
• /
• 2001

High quality PZT piezoelectric thin films were sputter- deposited on$ RuO_2$/$SiO_2$/Si substrates by using 2-step deposition method. As the first step, PZT seed layers were fabricated at a low temperature($475^{\circ}C$ ) to form a pure perovskite phase by reducing the volatility of Pb oxide. and then, as the second step, the PZT films were deposited at high temperatures ($530^{\circ}C$~$570^{\circ}C$) to reduce the defect density in the films. By this method, the pure perovskite phase was obtained at high deposition temperature range ($530^{\circ}C$~$570^{\circ}C$) and the superior electrical properties of PZT films were obtained on $RuO_2$substrate : 2Pr : 60$\mu$C/$\textrm{cm}^2$, $E_c: 60kV/cm, \;J_t: 10^{-6}A/cm^2\; at\; 250kV/cm$. The residual stress of PZT films fabricated by the 2-step deposition method was tensile and below 150MPa. It was attempted to control the residual stress in the PZT films by applying a negative bias to the substrate. As the amplitude of the substrate bias was increased, the residual tensile stress was slightly decreased, however, the ferroelectric properties of PZT films were degraded by ion bombardment.

• ETRI Journal
• /
• v.24 no.3
• /
• pp.211-220
• /
• 2002

This study characterizes an oxide etching process in a magnetically enhanced reactive ion etching (MERIE) reactor with a $CHF_3/CF_4$ gas chemistry. We use a statistical $2^{4-1}$ experimental design plus one center point to characterize the relationships between the process factors and etch responses. The factors that we varied in the design include RF power, pressure, and gas composition, and the modeled etch responses were the etch rate, etch selectivity to TiN, and uniformity. The developed models produced 3D response plots. Etching of $SiO_2$ mainly depends on F density and ion bombardment. $SiO_2$ etch selectivity to TiN sensitively depends on the F density in the plasma and the effects of ion bombardment. The process conditions for a high etch selectivity are a 0.3 to 0.5 $CF_4$ flow ratio and a -600 V to -650 V DC bias voltage according to the process pressure in our experiment. Etching uniformity was improved with an increase in the $CF_4$ flow ratio in the gas mixture, an increase in the source power, and a higher pressure. Our characterization of via etching in a $CHF_3/CF_4$ MERIE using neural networks was successful, economical, and effective. The results provide highly valuable information about etching mechanisms and optimum etching conditions.

• Journal of the Korean Electrochemical Society
• /
• v.7 no.4
• /
• pp.206-210
• /
• 2004

All array of carbon paste-based electrodes was prepared by screen printing the carbon paste modified with metal oxides $(TiO_2,\;RuO_2,\;PbO_2,\;Ni(OH)_2)$ and Prussian blue (PB). An electronic tongue system was assembled with the carbon-paste electrode array, and applied to discriminate the tastes of various commercial beverages and foods by measuring the chronoamperometric responses to the samples diluted in 0.1M carbonate buffer (pH 9.6). The results were analyzed with principal component analysis(PCA) method and plotted on two dimensional PCA coordinate; it was apparent that the amperometric electronic tongue system could discriminate the types of various foods and beverages.

• Journal of Electrochemical Science and Technology
• /
• v.7 no.4
• /
• pp.306-315
• /
• 2016

Amorphous vanadium titanates (aVTOs) are examined for use as a negative electrode in lithium-ion batteries. These amorphous mixed oxides are synthesized in nanosized particles (<100 nm) and flocculated to form secondary particles. The $V^{5+}$ ions in aVTO are found to occupy tetrahedral sites, whereas the $Ti^{4+}$ ions show fivefold coordination. Both are uniformly dispersed at the atomic scale in the amorphous oxide matrix, which has abundant structural defects. The first reversible capacity of an aVTO electrode ($295mAhg^{-1}$) is larger than that observed for a physically mixed electrode (1:2 $aV_2O_5$ | $aTiO_2$, $245mAhg^{-1}$). The discrepancy seems to be due to the unique four-coordinated $V^{5+}$ ions in aVTO, which either are more electron-accepting or generate more structural defects that serve as $Li^+$ storage sites. Coin-type Li/aVTO cells show a large irreversible capacity in the first cycle. When they are prepared under nitrogen (aVTO-N), the population of surface hydroxyl groups is greatly reduced. These groups irreversibly produce highly resistive inorganic compounds (LiOH and $Li_2O$), leading to increased irreversible capacity and electrode resistance. As a result, the material prepared under nitrogen shows higher Coulombic efficiency and rate capability.

• Journal of the Korean Magnetics Society
• /
• v.19 no.3
• /
• pp.94-99
• /
• 2009

We have studied the effects of oxygen partial pressure change on the physical properties of the $La_{0.7}Ca_{0.3}MnO_3$ thin films grown by Pulsed laser Deposition. Contrary to the previous reports, thin films of high curie temperature were successfully synthesized at very low oxygen partial pressure ($1.0{\times}10^{-5}$, $1.0{\times}10^{-6}Torr$). These observations indicate that the shape of plasma plume and the kinetic energy of the ablated species in it play an important role in determining the quality of samples. We also fabricated p-n heterojunction of $La_{0.7}Ca_{0.3}MnO_3$ and Nb-doped $SrTiO_3$. The current-voltage curves show rectifying behavior and, furthermore, the current responses to the applied magnetic field, indicating a potential possibility of device applications.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.06a
• /
• pp.179-182
• /
• 2006

The effect of electron beam irradiation on dye sensitized solar cell (DSSC) has been studied to examine degradation of DSSC. The high-energy electron beam irradiation affects on the materials and performance of dye sensitized solar cells. We have checked the effects of electron beam irradiation of $TiO_2$ substrate with and without dye adsorption on the photovoltaic performances of resulting DSSCS and also studied the structural and electrical properties of polymers after irradiation. All solar cells materials were irradiated by electron beams with an energy source of 2MeV at different dose rates of 60 kGy, 120 kGy 240 kGy and 900 kGy and then their photoelectrical parameters were measured at 1 sun $(100 mW/cm^2)$. It was shown that the efficiency of DSSC was decreased as increasing the dose of e-beam irradiation due to lowering in $TiO_2$ crystallinity, decomposition of dye and oxidation of FTO glasses. On the other hand, the performance of solid-state DSSC with polyethylene oxide based electrolyte was improved after irradiation of e-beam due to enhancement of its conductivity and breakage of crosslinking.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.06a
• /
• pp.187-191
• /
• 2006

Sputter deposition followed by surface treatment was studied using reactive RF plasma as a method for preparing titanium oxide $(TiO_2)$ films on the FTO $(SnO_2: F)$ substrate for dye-sensitized solar cells (DSCs). Anatase structure $TiO_2$ films deposited by reactive RF magnetron sputtering under the conditions of $Ar/O_2(5%)$ mixtures, RF power of 600W and substrate temperature of $400^{\circ}C$ were surface-treated by inductive coupled plasma (ICP) with $Ar/O_2$ mixtures at substrate temperature of $400^{\circ}C$, and thus the films were applied to the DSCs. We have chosen a solar cell width as a variable of a large-scaled DSCs and confirmed electric characteristics of an individual cell. As a result, the higher the internal resistance of DSC becomes, the wider the width gets. Internal resistance makes it difficult to collect photoelectron generated from dye. Ultimately up sizing DSC causes the increase of internal resistance and then has a bad effect on the cell characteristics.

• Korean Journal of Materials Research
• /
• v.29 no.8
• /
• pp.469-476
• /
• 2019

A lead-free bulk ceramic having a chemical formula $Ba_{0.8}Ca_{0.2}(Ti_{0.8}Zr_{0.1}Ce_{0.1})O_3$ (further termed as BCTZCO) is synthesized using mixed oxide route. The structural, dielectric, impedance, and conductivity properties, as well as the modulus of the synthesized sample are discussed in the present work. Analysis of X-ray diffraction data obtained at room temperature reveals the existence of some impurity phases. The natural surface morphology shows close packing of grains with few voids. Attempts have been made to study the (a) effect of microstructures containing grains, grain boundaries, and electrodes on impedance and capacitive characteristics, (b) relationship between properties and crystal structure, and (c) nature of the relaxation mechanism of the prepared samples. The relationship between the structure and physical properties is established. The frequency and temperature dependence of the dielectric properties reveal that this complex system has a high dielectric constant and low tangent loss. An analysis of impedance and related parameters illuminates the contributions of grains. The activation energy is determined for only the high temperature region in the temperature dependent AC conductivity graph. Deviation from the Debye behavior is seen in the Nyquist plot at different temperatures. The relaxation mechanism and the electrical transport properties in the sample are investigated with the help of various spectroscopic (i.e., dielectric, modulus, and impedance) techniques. This lead free sample will serve as a base for device engineering.